Bosch 1619EVS Support Question
Bosch 1619EVS Support Question
Find answers below for this question about Bosch 1619EVS - NA 3.25 HP Electronic Plunge Router.Need a Bosch 1619EVS manual? We have 2 online manuals for this item!
Question posted by ray72551 on August 30th, 2014
Depth Stop Turret/keyhole Misaligned With End Of Depth Rod
The person who posted this question about this Bosch product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Bosch 1619EVS Manual Pages
Operating Instructions - Page 2
...section of flammable liquids, gases, or dust. Do not overreach.
Do not force tool.
Power tools create sparks which it still does not fit, contact a qualified electrician to lose ...A wrench or a key that cannot be caught in serious away while operating a power tool.
The correct tool will increase the risk of electric shock.
Personal Safety
Stay alert, watch what you to...
Operating Instructions - Page 3
...: inside and outside cuts will be suitable for Routers
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may result in use only identical replacement parts. ...be violently thrown. Never hold the tool with the bit's cutting edge into existing walls or other adjustment devices are thrown). Check for misalignment or binding of moving parts, ...
Operating Instructions - Page 4
Never lay the tool down the workpiece and keep your router. Some examples of control during use the bit is unstable and tips.
...
After use . Never use and cause serious injury.
Failure to follow all the fasteners required for Router Table
Read and understand the tool manual and these exposures varies, depending on or near the spinning bit. Serious injury could occur if...
Operating Instructions - Page 6
...current
Type or a characteristic of the following symbols may be used on your tool. Higher number means greater speed
0
Infinitely variable selector with off
Speed is listed...PM Page 6
Symbols
IMPORTANT: Some of current
Class II construction
Designates Double Insulated Construction tools. Symbol Name
Designation/Explanation
V
Volts
Voltage (potential)
A
Amperes
Current
Hz
Hertz
...
Operating Instructions - Page 7
... OF BIT ROTATION
FIG. 2
COARSE ADJUSTMENT INDICATOR
COARSE ADJUSTMENT KNOB SPRING DEFEAT BUTTON DEPTH STOP TURRET
BACK VIEW
"LOCK-ON" BUTTON
ON/OFF TRIGGER SWITCH
PLUNGE LOCK OVERRIDE LEVER
PLUNGE LOCK LEVER
COLLET CHUCK
DUST EXTRACTION HOOD
Model number: Voltage rating: Amperage rating:
1619EVS 120 V 50 - 60Hz 15 A
No load speed: Collet capacities:
-7- BM2610995777 10/03...
Operating Instructions - Page 8
...chuck is self-extracting; WARNING
To prevent personal injury, always remove the plug from bottom of router).
4. Next, use the collet wrench to firmly tighten the collet chuck assembly in counter-clockwise... Once the collet chuck assembly is NOT necessary to strike the collet chuck to tool, do not use router bits greater
than 2" in the
armature assembly COLLET shaft with the flat side of...
Operating Instructions - Page 9
... the bottom of special carving. Operating Instructions
Bosch plunge routers are designed for edge forming. FIG. 7
TEMPLET GUIDE ADAPTER
TEMPLET GUIDE RELEASE LEVER
FIG. 6
MOUNTING SCREWS
PLUNGE LOCK LEVER
-9-
PLUNGING ACTION The plunge feature simplifies depth adjustments and will enable you to the left , release pressure on router and the router will connect the hood to lock (Fig...
Operating Instructions - Page 10
... coarse adjustment knob counter-clockwise to be moved independently of an inch.
Rotating the fine adjustment knob clockwise causes the depth rod to the right and press down , producing a deeper cut (in plunge depth or bit height.
1.
After zeroing, when the knob is available separately.)
COARSE ADJUSTMENT
LOCK
COARSE ADJUSTMENT
INDICATOR
REFERENCE MARK
FIG...
Operating Instructions - Page 11
...11
MAKING PROGESSIVELY DEEPER PLUNGE CUTS
When making a single deep cut:
1.
COARSE ADJUSTMENT
LOCK
FIG. 10
BIT COARSE ADJUSTMENT
KNOB
FIG. 11
REFERENCE MARK
COARSE ADJUSTMENT
INDICATOR
DEPTH ROD
DEPTH STOP TURRET
REFERENCE MARK
COARSE ADJUSTMENT
LOCK
DEPTH ROD
DEPTH STOP TURRET
BIT
-11- Loosen the coarse adjustment lock and lower the depth rod until the desired final depth is the...
Operating Instructions - Page 12
...bit life, and higher performance. Your router is continuously being
depressed, the trigger cannot be released.
SOFT START FEATURE Electronic feedback control minimizes torque twist customary in..., counter tops,
6
} 21,000
Smaller dia. The bit manufacturer may be changed while tool is not touching the work . Exact settings are achieved by squeezing or releasing the trigger. ...
Operating Instructions - Page 13
...depth. Always use piloted or bearing bits. Bearing guide bits have a ball bearing to the tool. This minimizes the possibility of damage from the top of endgrain.
-13- overloads motor.
5. You will minimize router... bit run-out and chatter.
Feeding too slow - Feed the router at a moderate rate. Always be perfectly smooth since any blowout at the end of the router,...
Operating Instructions - Page 14
... dust extraction hood.
Do not reach in area of the screw holes on the router base that will connect the hood to 1-1/4'' and 1-1/2'' vacuum hoses. CAUTION
To avoid entangling hoses, ...use of these instructions and tool
manual for the hood.
FIG. 16
M4 x 16mm SCREW
SUB-BASE
DUST EXTRACTION
HOOD
M4 x 16mm SCREW
-14- using two of the bit while the router is ON or plugged ...
Operating Instructions - Page 15
...line for use depends, of course, on the demands of the router's handles.
Its sub-base is often necessary to guide the tool in this path (Fig. 18). To most precisely re-center the... tighten them until they are over the matching set of cone when inserting into 1/4" collet, wider end of flathead screws (included) and the countersunk screw holes in the base.
2. For routing operations such...
Operating Instructions - Page 16
...SCREW CUT
THUMB SCREW (BEHIND POST)
FINE ADJUSTMENT INDICATOR
DESIRED WIDTH
WORKPIECE
ROUTER GUIDE RODS
-16- Insert the templet guide and release the lever to create circles and arcs.... knob and indicator for cutting repeated patterns, special designs, inlays, and other suitable cutting tool. For complete instructions on the bottom of plywood, hardboard, metal or even plastic, and the...
Operating Instructions - Page 17
... the height of keyhole slot.
g. DEPTH ROD
FIG. 24
SPRING DEFEAT BUTTON
1. Engage plunge lock override lever as shown in the Bosch router table. Release
COARSE ADJUSTMENT
LOCK
coarse adjust lock, and lower depth rod into the large end of the bit when the router is now disengaged. Rotate depth stop turret to the manual that the large end of the depth rod.
Note: This...
Operating Instructions - Page 18
...extension onto the end of the fine adjustment knob. (Fig. 25)
FIG. 25
CONNECT THE ROUTER AND THE ROUTER TABLE SWITCH
To prepare for mounting to the
Bosch router table. FEEDING THE...the depth rod to start and stop turret. (The rod needs to the left.
Reactivate the plunge return spring by turning it comes to the instructions provided with the fine adjustment knob. Plug the router ...
Operating Instructions - Page 19
...
Service Center or Authorized Bosch Service
Station. CARBON BRUSHES The brushes and commutator in Meters 25 50 100 150 15 30 60 120
3-6 6-8 8-10 10-12 12-16
18 ... that all tool
service be
lubricated or coarse adjustment lock will prevent excessive
voltage drop, loss of dependable service. Cleaning
! The tool may result in A.W.G.
CAUTION
The depth rod and coarse adjustment...
Parts Diagram - Page 2
...14 3 600 900 526 Ball Bearing
61
16 1 604 336 008 Brush Holder {2}
25
18 2 610 904 114 Screw {4}
89
19 2 910 611 020 Screw {2}
89...
43 2 610 996 118 Baffle
24
44 2 610 996 119 Lock Rod
88
45 2 610 996 120 Spring
27
47 1 607 233 147 ...62 2 610 996 135 Lock Lever
64
63 2 610 996 136 Depth Stop
87
65 2 610 909 058 Screw
89
66 2 610 996 137... Time Chart 1619EVS PLUNGE ROUTER
Pos.
Similar Questions
Grinder Stopped Working. Off-on Switch Appears To Be Inoperable.
I took the head off to perhaps get at the switch but that only led me to more trouble. Still can't g...
I took the head off to perhaps get at the switch but that only led me to more trouble. Still can't g...
(Posted by autonut61260 2 years ago)
Connecting Rod Replacement Videos
My pin snapped so I bought another broken 1640vs off eBay it has same matching pin. I put the unbrok...
My pin snapped so I bought another broken 1640vs off eBay it has same matching pin. I put the unbrok...
(Posted by Michaemoore 5 years ago)
Bocsh 1250 Devs Stopped Rotating
stopped rotating and makes bussing sound, put new speed control switch in but was not the problem
stopped rotating and makes bussing sound, put new speed control switch in but was not the problem
(Posted by tomaspros 11 years ago)
How To Replace Depth Adjustment Handle
(Posted by tlaskielaskie9 11 years ago)
Why No Rail Pressure. Removed The Cp3 Pump, Changed Crankshaft And #6 Rod.
(Posted by kevinlmiller 11 years ago)