Bosch 1199VSR Support Question
Bosch 1199VSR Support Question
Find answers below for this question about Bosch 1199VSR - NA VSR 1/2" Dual Torque Hammer Drill.Need a Bosch 1199VSR manual? We have 1 online manual for this item!
Question posted by Dougje1 on July 14th, 2014
How To Replace The Cord On 1199 Vsr Drill
Cord is damaged and I need instructions on the best way to replace it
Current Answers
Related Bosch 1199VSR Manual Pages
Operating Instructions - Page 2
...tools or pull the plug from moving parts. Do not use any way. Do not overreach. Distractions can cause you are equipped with all instructions listed below, may result in . If operating the power tool...and well lit. Never use common sense when operating a power tool. Replace damaged cords immediately. These cords are in electric shock, fire and/or serious personal injury. Personal...
Operating Instructions - Page 3
....
Follow instructions in the Maintenance section of starting the tool accidentally. Use of the tool "live" and shock the operator. Unstable support can cause hearing loss. Position the cord clear of control and injury.
Maintain tools with a "live" wire will do the job better and safer at the rate for Hammer Drills
Hold tool by poorly maintained tools.
If damaged...
Operating Instructions - Page 4
..."Lock-ON" button. Your risk from the drill before the bit is locked "ON" during the use, be hot after prolonged use dull or damaged bits and accessories.
Be aware of the location ...then immediately releasing it at high velocity striking you do this type of work , the reaction torque of the tool could become bound or jammed in the opposite direction as those dust masks that are :
...
Operating Instructions - Page 5
...or reciprocation per minute
0
Off position
Zero speed, zero torque...
1, 2, 3, ...
This symbol designates that this tool is listed by Underwriters Laboratories, and listed to Canadian Standards ...that this tool is listed by Underwriters Laboratories.
This symbol designates that this tool complies to operate the tool better and safer. Symbols
IMPORTANT: Some of drill bits,...
Operating Instructions - Page 6
Hammer Drill
FIG. 1
DRILL/HAMMER DRILL SELECTION DIAL
REVERSING SWITCH LEVER
COLLAR MOUNT CHUCK
RUBBERIZED GRIP
TRIGGER
DEPTH GAUGE
HAND GRIP
DEPTH GAUGE RELEASE BUTTON
"LOCK-ON" BUTTON
GEAR CHANGE SELECTION DIAL
CHUCK KEY & STORAGE AREA
Model number No load speed 1 No load speed 2 Maximum capacities Chuck capacity Material Concrete Aluminum Steel
1199VSR
n0 0-1,100/min n0...
Operating Instructions - Page 7
...torque required for various drilling/hammer drilling applications. DEPTH GAUGE Your drilling depth can be released. "LOCK-ON" BUTTON The "Lock-ON" button, located above the trigger allows for continuous operation at a complete standstill.
Shifting during
rotation of the tool...gauge in place.
Operating Instructions
TRIGGER CONTROLLED VARIABLE SPEED Your tool is equipped with the ...
Operating Instructions - Page 8
...drill only 2/3 the proper length. Countersink same diameter as you to both tool and bit.
The chuck can be damaging to fasten materials together with your bits and do all of your hammer drill in the drill...driving screws, pilot and clearance holes should be drilled. FIG. 4
Counter Clockwise
Clockwise
Operating Tips
You will eliminate the need for screw sizes No. 6, 8, 10 and ...
Operating Instructions - Page 9
...drill a cleaner hole if you need to apply to keep the bit from spinning.
Use only bits that the bit does not just spin in full contact with brushes requires high speeds. Maintain enough pressure to the tool... POLISHING You will be used. Use of the wire come in such a way that is not exceeded by slowing the drill to the work . Apply the brush to a stop. Then complete the hole...
Operating Instructions - Page 10
...most effectively with compressed air.
wire extension cords that all tool service be replaced at every second brush change . WARNING
...tool may result in misplacing of the motor, we recommend every two to clean by unauthorized
personnel may
be examined. CAUTION
Certain cleaning agents and solvents damage
plastic parts.
NOTE: The smaller the gauge number, the heavier the cord...
Similar Questions
Replacing Tensioner Levers Bosch 1239d Sander
How do nyou replace the tensioner lever on the Bosch 1239D half sheet sander
How do nyou replace the tensioner lever on the Bosch 1239D half sheet sander
(Posted by maxshepherd 1 year ago)
Drill Bit Wobbles
My Hammer drill works but the bit wobbles, it is off center. how can i fix it?
My Hammer drill works but the bit wobbles, it is off center. how can i fix it?
(Posted by hj518 7 years ago)
How To Replace Fan Assembly Bosch 3107dvs.
The threads appear to be stripped in the fan assembly. It looks like I need to purchase the entire a...
The threads appear to be stripped in the fan assembly. It looks like I need to purchase the entire a...
(Posted by mycontractor 9 years ago)
Replace 6' With 5' Pad?
The pad on my 3727DEVS 6" Bosch sander needs replacing. Can I put a new 5" pad on the base (since 5"...
The pad on my 3727DEVS 6" Bosch sander needs replacing. Can I put a new 5" pad on the base (since 5"...
(Posted by teriperkins 11 years ago)
Chuck Key Size For 1199vsr Drill?
What is the correct size of chuck key for the 1199VSR drill, I purchased a 1/2 "X1/4 pilot, ans a 1/...
What is the correct size of chuck key for the 1199VSR drill, I purchased a 1/2 "X1/4 pilot, ans a 1/...
(Posted by aguada2000 13 years ago)