Black & Decker NST2118 Support Question
Black & Decker NST2118 Support Question
Find answers below for this question about Black & Decker NST2118.Need a Black & Decker NST2118 manual? We have 2 online manuals for this item!
Question posted by gbeaulieu28 on June 23rd, 2015
Nst1118 Type 2 Oem Replacement Blade ?
The only replacement blade I can find is # 234805-00. The # 234805 has 3 holes and doesn't show up as a direct replacement to the NST1118.The OEM NST1118 has 2 diagonal holes. Is there no OEM replacement or is drilling needed ? : (
Current Answers
Answer #1: Posted by TechSupport101 on June 24th, 2015 6:57 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,285
Member since:
May 24th, 2013 Points: 12,171,285
Go here http://servicenet.blackanddecker.com/parts/index?_ga=1.145855988.177392367.1435153968 for Black & Decker OEM parts.
Related Black & Decker NST2118 Manual Pages
Type 1 Manual - NST1118 - Page 1
... will overheat (page 7).
• When replacing the line, use only .065 inch diameter ROUND line (B&D Model #AF-100 is recommended) - If you call 1-800-544-6986 from 8 a.m. INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.
Model # NST1118, NST2118
TRIMMER / EDGER INSTRUCTION MANUAL
Model Numbers NST1118, NST2118
Thank you have access to...
Type 1 Manual - NST1118 - Page 2
... for Battery Chargers 4 Charging Procedure 5 Assembly / Adjustment 7 Operating Instructions 8 Replacement Accessories 9 Maintenance 11 Troubleshooting 12 Service Information 12 Full Two-Year Home Use ...wearing open sandals. IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS
WARNING: When using electric gardening appliances, basic
safety precautions should be thrown out at a safe distance ...
Type 1 Manual - NST1118 - Page 3
...definitions are as follows:
V volts
A amperes
Hz hertz
W watts
min minutes ..........direct current
alternating current no no load speed
Class II Construction
............earthing terminal
instructions in ...this tool for use whenever the battery is damaged should be properly repaired or replaced by this manual. For example,
elsewhere in charger or unit. which it with...
Type 1 Manual - NST1118 - Page 4
... short circuits. prohibit transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they be listed by Underwriters Laboratories (U.L.). Other types of batteries may result in a risk of power and overheating.
Type 1 Manual - NST1118 - Page 6
... air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). Longest life and best performance can be fully charged and then removed from direct sunlight and excess heat or cold. DO NOT CONTINUE using unit with the battery pack removed and on maintenance charge, it may also lose its...
Type 1 Manual - NST1118 - Page 7
... as shown in figure 6.
e
• Continue to complete the guard
assembly.
• Once the guard is installed,
remove the covering from the
line cut-off blade, located on so that you
release them with the
Black & Decker logo facing
upward).
Phillips Screwdriver INSTALLING THE GUARD
ATTACHING THE AUXILIARY HANDLE
• To...
Type 1 Manual - NST1118 - Page 8
... raise or lower the
handle.
• The handle should be adjusted by rotating it opposite of the
direction shown in figure 10.
10
8 CAUTION: Inspect area to be bent outwardly into place (figure 8).
... is
achieved, tighten the collar
by
loosening the collar (h) and
rotating it in the direction of the
trimmer can be
adjusted so that conforms
to avoid any wire which
might be...
Type 1 Manual - NST1118 - Page 9
...100. Cutting line will lock in this tool could be hazardous.
9 Use Black & Decker replacement spool Model No. When using the tool, retract the wire edge guide to the original position,... dealer or authorized service center. • Other replacement parts (guards, spool caps, etc.) are being cut. WARNING: The use the
appropriate type of the way.
The tool will wear faster ...
Type 1 Manual - NST1118 - Page 10
...
cutting line from the spool.
• Make a fold at the end of housing becomes dislodged, replace in figure 16.
10 q
• Remove any dirt and grass
from the spool and housing.
... (19mm)(q).
CAUTION: To avoid tool
damage, if the cutting line protrudes beyond the
p
n
trimming blade, cut it off so
that it
is also available for purchase from your local retailer.
Model #...
Type 1 Manual - NST1118 - Page 11
... inch (19mm) end of the bulk line into the
17
t
hole (s) in the spool
adjacent to the slot as described
in "REPLACING THE SPOOL". It is illegal to facilitate the collection of the blade with Black & Decker and other qualified service organizations, always using ...the cutting line onto the spool in cooperation with a file. RBRC in the direction of the guard can dry out over time.
Type 1 Manual - NST1118 - Page 12
...snaps securely into the housing. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you may have any defects in the...blade. Carefully clean it if necessary. • Check that the cutting line does not protrude more than approximately 5-3/8 inches (136mm) from the spool.
Proof of the phone directory. Replace ...
Type 1 Manual - NST1118 - Page 13
...: This warranty does not apply to products sold in Latin America, check country specific warranty information contained in Latin America. Joppa Rd. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call the local company or see the website for warranty information. Imported by Black & Decker (U.S.) Inc...
Type 1 Manual - NST1118QS - Page 1
... tape from the line and cutting blade on charge. NOTE: NST1118 contains one battery.
There is charged... logo facing up. • Press in either direction and simultaneously pull the trigger. Mode de taillage...hole on the side of the upper housing (B1). • Partially push the handle on until it will not engage. E
8) Depress the lock off button during operation. NST1118 / NST2118...
Similar Questions
Battery Stop Charging, Can I Replace The Battery
battery stop charging, can I replace the battery
battery stop charging, can I replace the battery
(Posted by bmsbsmith61 10 months ago)
How Do I Get The String To Feed Out Automatically?
(Posted by DBranes0453 1 year ago)
Gear Assembly Removel On Lst136 Type 2 40 Volt
I am trying to replace DWB-90559541-03 gear assembly on my lst136 type 2 40 volt trimmer. I cant fin...
I am trying to replace DWB-90559541-03 gear assembly on my lst136 type 2 40 volt trimmer. I cant fin...
(Posted by jayrues1950 2 years ago)