Binatone Concept Combo 3525 Support Question
Binatone Concept Combo 3525 Support Question
Find answers below for this question about Binatone Concept Combo 3525.Need a Binatone Concept Combo 3525 manual? We have 1 online manual for this item!
Question posted by derrickgeorgeking on January 16th, 2018
Registering A Binatone 3525 Hand Set.
The simple instructions received do not work. Pressing Menu/Ok followed by up and down does not bring up a display to enter the 0000 pin
Current Answers
Answer #1: Posted by BusterDoogen on January 16th, 2018 6:01 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
Go to page 47 for the extra handset registration procedure.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Binatone Concept Combo 3525 Manual Pages
User Manual - Page 19
...
PB STATUS
CALL LOG
MISSED RECEIVED DIALED
DATE & TIME
TIME FORMAT SETt CLOCK
LANGUAGE
ENGLISH DEUTSCH FRANCAIS ITALIANO TURKCE ESPANOL GREEK SVENSKA NORSK NEDERLANDS
SETTINGS
RING SETUP DELETE HS DIAL MODE FLASH TIME KEY TONE CHANGE PIN BS DEFAULT
PAGE ALL HS
REGISTRATION ANS.
Sub menu ADD TO PB?
(Press MENU/OK if
DELETE?
or the first...
User Manual - Page 23
... call timer is displayed as soon as you cannot correct it with Caller Display) Press to access the Call List and press to dial out ...Enter the phone number and press to connect to select the desired redial number. When entering the number, if you make a mistake, press to delete digits.
4.1.2 Direct Dialling Press to connect to the line and then enter the phone number. (Note: if you enter...
User Manual - Page 29
...pressed on that you want to call, or enter "9" to call all handsets and the base.
3.
Press . If the called base rings and the corded... one handset is an incoming call during the intercom calling, the phone will ring with a "7" and a "9".
2.
4.17 Find ...the corded base:
You can answer the external call.
27
Note: If there is registered to the base station, pressing will display, ...
User Manual - Page 30
...During an external call , or press "9" to . 3. In idle mode, press and the registered handsets will display. 2. In idle mode, press and the registered handset numbers
will display. 2. Enter the number for the handset you want to transfer the call to call with a "9". 2. Using the corded base: 1. Enter the handset number you want to call : 1. Press to all the other handset...
User Manual - Page 31
... 4.18.3 (corded). 2. Using the corded base: During an external call .
29 Press on the calling handset or put on hold the star key on the calling base to show all the other party still connected to . Any party (base or handset) can exit the conference and leave the other registered handset numbers,
plus a "9". 2. Follow Steps...
User Manual - Page 39
... change to personalise your phone the way you like it to select DATE & TIME. 3. Press and to work. Press and to select SET DATE. 4. Press and to select HS SETTINGS. 2. Press and then enter the time information in Section 7.1.1. 5. Press and to select DATE & TIME. 3. Press and to select SET TIME. 4. Note: By default, the current time will display, starting from 01...
User Manual - Page 40
... 24 hour format. 3. Follow Steps 1 to show ALARM. 3. Enter the alarm time in Section 7.2.1. 2. If the snooze function is the same as the settings of the handset ringer
volume. Note: a. An alarm tone will be ON) 1. d. Press to alert the user the alarm time is sounding, to display "SNOOZE". 4. 7.2 Alarm Settings You can set , the alarm icon...
User Manual - Page 41
... different alert tones are talking on by default, but can be displayed. 5. Press to select the desired ringer
volume (a total of Range Tone - Low Battery Tone - Press and to select RING SETUP. 3. Press and to selectHS SETTINGS. 2. Press and to select melody you are set on the phone to alert you that you want to select RING SETUP...
User Manual - Page 43
... value of 100ms), MEDIUM (300ms) or LONG (600ms).
1. Press and to select DIAL MODE. 3. Press and to select BS SETTINGS. 2. Enter the 4-digit system PIN (default 0000). 5. Press and to select FLASH TIME. 3. A de-registered handset will need to change the recall (flash) time if your phone is set, you can press the * key to switch to TONE
dialling for the...
User Manual - Page 44
... unchaged. 1. Press to select CHANGE PIN. 3. Note: If the new PIN entered in Step 5, you must enter the new system PIN at step 5 again. 7. Press to display NEW PIN?------, and enter your new
4-digit system PIN again. Enter the 4-digit system PIN(default 0000). 4. Enter the old system PIN. 5. Press and to its default
settings
42 Press to confirm, and the phone will be...
User Manual - Page 45
... will need to be de-registered. Press and to select SET CLOCK. 3. Press and the first registered handset number is displayed with the last two
digits of your handsets becomes faulty or lost and needs to enter the 4-digit system PIN in 24-hour format. 11. Press to show "PIN?", enter the 4-digit
PIN code (default setting is 0000). 4. Press and the selected handset will...
User Manual - Page 46
... can adjust the volume level of TONE (also called DTMF) unless the phone is connected to an old exchange that only recognises PULSE dialling.
Press to confirm the setting. Press to select SETTINGS. 2. Press and to select EXT. Note: The respective ringer melody will display.
7.8 Set the Dial Mode You should normally leave the dialling mode at its...
User Manual - Page 47
...to select ON or OFF. 4. The display will show "NEW PIN", enter the new PIN and press
. 5. In Idle: 1. Press and to select SETTINGS. 2. The display will show "PIN?", enter the 4-digit PIN
(default setting is connected to a PBX. 7.9 Set the Recall (Flash) Time You may need to change the recall (flash) time if your phone is 0000) and press . 4. Press to confirm.
7.12 Change the...
User Manual - Page 49
.... If the display shows "REGISTER ", you need to register the handset again using the following handset sequence must be completed within range. 8 REGISTRATION IMPORTANT: When you purchase your phone system, all cordless handsets are already registered to your base, so you do not need to register them. The handset's display should show
REGISTRATION, and then press to standby mode...
User Manual - Page 50
... display on the handset LCD.
48 When the answering machine is set to OFF, calls will be answered after 14 rings and the answer only message will be answered after the set to ON, calls will not be played to your phone. When the answering machine is set , the caller can then leave you a message. Press...
User Manual - Page 55
... your desired recording
time from the available options 60S, 120S, 180S or UNLIMITED. (The current selection is on the base. MACHINE. 2. Press and to select OFF or ON. (The current setting will be heard when leaving a message, the base screening can then identify the caller and decide whether to take the call...
User Manual - Page 56
... 9.5.9.2. 9.5.9.1 Change the 4-Digit Remote Access PIN 1. Press and to show PIN?----, then enter the Old PIN.
(Default Remote Access PIN is 0000). 5. Press to select TAM SETTINGS. 3. Press to select ANS. Press and to reconfirm.
54 Press and to show NEW PIN?----, then enteryour new 4-digit PIN. 6. Press to select TAM SETTINGS. 3. 9.5.8 Change the Compression Rate Three...
User Manual - Page 57
... the remote access mode after the OGM, and the 4-digit PIN
should be follow without any messages.
Press and to select TAM SETTINGS. 3. The OGM will be entered during or after 14 rings. Note: If the 4-digit Remote Access PIN is not accepted, you will hear a multiple beep, and if it is switched off the answering...
User Manual - Page 58
...base to select.
9.7 Outgoing Message Settings 9.7.1 Record your Outgoing Message (...corded base:
9.6 Switching the TAM On/Off When the TAM is switched on, the TAM ON/OFF indicator will be off unless there are new messages recorded. If your new personal outgoing message and display PLAYING OGM. Press and hold until you hear a beep and
RECORDING appears on or off. 9.6.2 Using the Menu 1. Press...
User Manual - Page 65
... Skip to select ANS. Press and the display will show "PIN ?", and then enter
the system PIN code. (Default is playing
2
Delete the current message playing. Repeat playing the current message
4
from a tone-dialling phone. Press to restore the TAM settings to select CHANGE PIN. 4. Keys
Functions
While message is not playing While message is 0000)
5. Press and to default...
Similar Questions
Handset Out Of Cradle Tone
How do you set the phone to issue an alarm tone when the handset is left off the cradle?
How do you set the phone to issue an alarm tone when the handset is left off the cradle?
(Posted by nexus1 1 year ago)
How To Unlock Cordless Hand Set Speakeasy Combo 3865
(Posted by Anonymous-171958 1 year ago)
No Dialling Tone When I Pick Up Hand Set.
My phone rings when people call me, but when I pick up they can hear me but I can't hear them. Also ...
My phone rings when people call me, but when I pick up they can hear me but I can't hear them. Also ...
(Posted by samuijules 8 years ago)
How Do You Stop Main Hand Set Ringing Out.
We purchased the twin 3525 about 8 months ago. The hand set base station located in the hall continu...
We purchased the twin 3525 about 8 months ago. The hand set base station located in the hall continu...
(Posted by richardfir9 9 years ago)
Hand Set Will Not Make Calls Keeps Not Possible
(Posted by richardbarlow2 10 years ago)