Home » Bernina » Sewing Machines » Bernina 530

Bernina 530 Support Question

Find answers below for this question about Bernina 530.
Need a Bernina 530 manual? We have 1 online manual for this item!

Bernina Overview Questions Manuals Reviews Videos Research

Question posted by rickkramer9132 on April 29th, 2012

350 Pe Makes A Lot Of Noise When Switched On,Brand New Out Of The Box

is this nomal, diddnt expect a loud humming?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by maryayaya on February 25th, 2013 4:43 PM

maryayaya

Member since:
February 25th, 2013

Points: 0

100
points

Mine did that too. All the means is that the bobbin winder lever was pushed in to wind the bobbin (even if there's no bobbin on there). Pull it away from the rod that the bobbin goes on - i.e. pull that switch to the right, away from the rod, and the noise will go away.

Related Bernina 530 Manual Pages

Manual - Page 3

... obligations. 104 The Warranty Certificate is in its raised position. Fritz Gegauf Ltd. BERNINA Sewing Machine Factory Steekborn - Note To prevent damage to presser foot, place a piece of use. In order to avoid thread jamming, make sure after every sewing operation that the take-up lever is sent to them the card supplied with...

Manual - Page 7

... 1 Needle Plate 3 Needle Holder 4 Thread Tension Face Plate 6 Light Switch 7 Take-up lever 0 Thread Guide 9 Ornamental Stitch Selector I' 10 Zigzag/ Ornamental Stitch control Balance wheel 16 Bobbin Winder Shaft 17 Drop Feed Knob 10 Bed Plate Zigzag, Plain Stitch and 12 Buttonhole sewing Control knob 19 Knee Control Lever 10 Free Arm...

Manual - Page 8

... Instructions being marked and identified. 1 Cover Plate 2 Needle Plate 3 Needle Holder 4 Thread Tension 5 Face Plate 6 Light Switch 7 Take-up lever Thread Guide 11 Balance wheel 17 Drop Feed Knob Zigzag, Plain Stitch and 12 Buttonhole sewing Control knob 18 Bed Plate 19 Knee Control Lever 13 Needle Displacement lever 20 Free Arm...

Manual - Page 9

... the machine. The bulb ran be used away from the foot control to the mains voltage. turn it will evenly distribute light over the sewing area. the speed of the motor (Fig. 4). It is switched on... foot control plate is depressed the greater the speed of the machine. Electrical part Fig. 4 12 The drive of the BEIININA-Record Model 530-2 and Model 532-2 is by slight pressure of the foot ...

Manual - Page 11

..., and from the stand below tension spring 28 and allow it is pulled. Now release latch and make sure that it to come out at the base of the bobbin case is possible only when the ... tension discs of the bobbin tensioning device 24 unto the bobbin 26. S When replacing bobbin in case, make sure that bobbin turns in the direction of tension spring 29. Bringing the thread to the rim. Care...

Manual - Page 13

...now slightly pulled, which causes the bobbin thread to rear. Top and bottom threads are in the tension box 31, up to the thread tension between the front or rear tension disc. O 8 8 t2 ... 7 and needle are slightly tightened and placed rearwardly under the presser foot. Make sure that take -op lever is placed on one of the two pins 22...machine. y id ERNIN 4 Thread tension 7 Take-up .

Manual - Page 14

...the table is slid onto the free arm, make sure that cleaning and oiling can be placed .... Fit. 10 Cleaning and Oiling Cleaning the Machine rigs. 11 and 12 Fluff is pointing to... so that the locking lever 3S is collected during sewing particularly around the shuttle. To remove the cover plate... normal adjustment of the right hand. Thread Tension Box Fig. 9 The thread tension is moved to ...

Manual - Page 16

... months if the machine is in daily use so that all other portions of the motor. 3. The motor of every new machine is generally due to...noise. 6. To oil the motor, remove the motor housing. Always make sure that it should be oiled during the first year. 4. The two diagonally opposite nickel-plated screws below the bed plate are removed and 4-5 drops light, odorless sewing machine...

Manual - Page 17

... bar with presser foot is why the BERN1NA Record Model 530-2/532-2 has been equipped with a presser foot holding device...and slide the presser foot into the cloth presser bar cone making sure that it will suffice 42 to release the clamping boss... with Standard and Special Presser Foot Exchanging Presser Foot Different sewing work requires more or less frequent exchange of the presser foot...

Manual - Page 18

... of the stitch length dial is above the line mark on the side, the 31 In this position, the machine will sew forward or backward, making long or short stitches. Forward and Backward Sewing and Adjustment of Stitch lengths According to the left to lower or raise the feed dog. Raise take-up lever...

Manual - Page 19

...thanks to a greater or lesser degree. Lower feed dog by hopper foot. 3. The BERNINA-Record Model 530-2 and Model 532-2 can easily be used for Linen, etc. Set stitch regulator to prevent the ...lever is raised so that the feed dog is below the line mark, the machine will sew forward. In particular, make sure that the work can be removed. Remove presser foot and replace by turning ...

Manual - Page 20

Then cover the parallel rows with new parallel rows at the edge of the area darned. a The first covering rows are sewn a little ...one another as close to the exact area originully damaged (Fig. 17e). It is advantageous to make rows of different lengths in the darning area by sewing stitch rows from left to prevent the material from tearing at right angles running front to obtain a...

Manual - Page 21

... ring 49 of the darning attachment off the outer ring by the stocking (Fig. 19), and make sure that the damaged area rests on the free arm and set the small stud at . the...as far as it is advantageous to slide the darning ring as close to the left to prevent running. Then sew a line of stitches across the direction of different lengths and as far to one -quarter turn and the darning...

Manual - Page 22

... the lap hemmer. 2nd Operation (Fig. 20 b): The two sections are folded over and sewn down. Make sure that the seam formed stands up like a pleat. Lap hems are obtained in two operations, viz.... : 1st Operation (Fig. 20a): Arrange the fabric sections to make Run and Fell seam; Lap Hemmer Tailored effect obtained by having both under the lap hemmer as when...

Manual - Page 24

.... and inserting zips. Then sew a new seam following the direction of the seam is raised from the edger... the arrow obliquely to the right presser foot edge. Then make a seam and shift 4J-4, the material to the right...Left-centre-right Adjustment On top of the' machine is particularly suitable for quilting work as desired. e. When sewing zigzag, this knob may be used for edgestitching,...

Manual - Page 28

... inlay C) the raised buttonhole A. The sewing of the buttonhole with the new buttonhole device is sewn with normal lower thread tension, but with special threading of the bobbin case (see Fig. 27). THREAD CUTTER 1t of Cx 50 The presser foot clamping lever on the BERNINA sewing machine at a convenient spot is provided with...

Manual - Page 38

...stockings is employed to zero, lower foot and fasten with wool is performed in the button and sew button on with wool, use darning cotton. Darning with several stitches. The rows are pulled ...hole buttons, shift the cloth with wool rows. 2. Thread tension is covered with the button and make 6-8 stitches in like manner. Press-studs and hooks are sewn on its shank and place button...

Manual - Page 39

...ran a zigzag stitch will be of the fuut by sewing cut at the left to project over the edges of the cut-out on the right side of the material. Make sure that , the mend remains elastic, and care should... slot of the foot, and the thread end allowed to right and vice-versa, run by run, by sewing a wider (2112), short zigzag line over the rear edge of the same colour as shown in Fig,...

Manual - Page 45

...to produce the largest stitch width. 84 After threading the machine, stitching can be locked and stay in raised position. This plate..., marked by a zigzag line, i.e. placing the lever, make sure that the white line thereon lines up and then release...-hand side of the zigzag lever is effected as ordinary sewing. When switching back to normal zigzag stitches, place control lever in the...

Manual - Page 53

...jammed thread ends and dust from the shuttle race. Make sure that the lock- Shuttle point has become jammed... either furward or in reverse or if an abnormally loud noise is properly engaged. Threads should fail to faulty manipulation... 57 'E VT7i , 4 ...Z.( • It Blocked Shells If the machine should never be kept in heated rooms. Bolton' Thread Breakage Bottom thread ...