American Standard Champion-4 Support Question
American Standard Champion-4 Support Question
Find answers below for this question about American Standard Champion-4 - 3180.016.165 Townsend Right Height.Need a American Standard Champion-4 manual? We have 2 online manuals for this item!
Question posted by affordable1010 on May 14th, 2013
Need A Bolt Kit For Tank To Bowl On A Cadet Toilet. 1/4' X 3' Long 1/4-20 Thre
Bolt kit for tank to bowl Cadet toilet. Bolt sz 1/4"x3" L. Thread 1/4-20 incl washers, nuts & gasket 1/4" and fiber washer 1/4" dia.
Current Answers
Related American Standard Champion-4 Manual Pages
Installation Instructions - Page 1
... AND MATERIALS
Putty Knife Hacksaw Closet Bolts
Regular Screwdriver Wax Ring/Gasket Tape Measure
Adjustable Wrench Flexible Supply Tube Carpenters Level
Sealant 1/2" Deep Well Nut Driver or Deep Well Socket Wrench
1 REMOVE OLD TOILET
a. b. NOTE: If replacing valve, first shut off main water supply! Remove old mounting hardware, remove toilet and plug floor waste opening...
Installation Instructions - Page 2
...)
3
4
CLOSET FLANGE
SEALANT
WAX RING
A CLOSET BOLTS
INSTALL CLOSET BOLTS Install closet bolts in flange channel, turn 90°, and slide into
place 6" (152 mm) apart and parallel to prevent damage), and install wax ring evenly around toilet base. Side of ring facing toilet. b. V
Loosely install retainer washers and nuts. 2 NOTE: DRAWINGS ARE FOR DIMENSIONAL PURPOSES ONLY...
Installation Instructions - Page 3
Smooth off the bead of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes.
Use the included deep socket tool to help get nuts started on washers. (If necessary, cut bolt height to wall, alternately tighten hex nuts keeping tank even and level until toilet is void if any further. With tank parallel to size before...
Installation Instructions - Page 4
... TUBE
TANK LEVER
FLOAT CUP
Fig. 10A
With correct washers in place (see Fig. 10A) and take up or down. NOTE: DO NOT ADD ANY FOREIGN MATERIALS TO THE SEALING SURFACE.
- 4 -
730529-100 Rev. Remove piston top and gasket. 6.
VALVE BODY
SHANK WASHER
WATER LEVEL ADJUSTMENT
ROD
ADJUSTABLE HEIGHT
LOCK NUT CONE WASHER
COUPLING NUT (HAND TIGHT ONLY)
THREADED...
Installation Instructions - Page 5
...® 4 LH Trip Lever Bolt Cap Kit (Incl. 2 Covers & Washers) Champion® 4 Fluidmaster 400a Valve Champion® 4 Flush Valve Seal Kit Champion® 4 Flush Valve Assembly Champion® 4 Clevis Pin Assembly Champion® 4 PVC Refill Tube Champion® 4 Tank To Bowl Coupling Kit #241 Champion® 4 Tank Cover Champion® 4 Tank Cover Champion® 4 Tank Cover Clip for more...
Valve Replacement - Page 1
...Replace the tank lid. Remove...bowl and tighten the tank mounting fasteners in a alternating manner.
Reconnect the water supply. ISPN 7301121-100 PART# 5-1835 REV.1 01/07 Place the tank on it's side, remove the coupling gasket (not shown) and lock nut...of the refill tube attachment. Replace the coupling gasket over the lock nut, re-fit the tank assembly to the valve overflow at the location ...
Similar Questions
My 6 Year Old Toilet Has A Lot Of Hair Line Cracks In The Area Where The Seat Re
toilet has many hair line cracks in the area where the seat rests, should I be concerned?
toilet has many hair line cracks in the area where the seat rests, should I be concerned?
(Posted by Vince61038 1 year ago)
American Standard Toilets How To Fix Loose Seat On Cadet 3
(Posted by Nigelhosyo 9 years ago)
American Standard Champion 4 Toilet Valve Won't Stop Running
(Posted by langmom3 9 years ago)
Dimensions From C/l Of Bolts To Front Of Bowl. Both Round & Elongated
(Posted by sobierajsr 10 years ago)
Why Has Does This Toilet Not Flush Properly?
I purchased THREE of the same toilets and replaced one while it was still in warranty. All three toi...
I purchased THREE of the same toilets and replaced one while it was still in warranty. All three toi...
(Posted by throon2003 12 years ago)