Amana NFW7300WW Support Question
Amana NFW7300WW Support Question
Find answers below for this question about Amana NFW7300WW.Need a Amana NFW7300WW manual? We have 4 online manuals for this item!
Question posted by lesap99 on July 9th, 2014
System Timer
I had the clog fixed on my Machine now it will spin and drain, But the problem now is that every cycle it will stop and beep and i have to click it off, then click it on and set it on to the next cycle like wash,,then it will beep and I have to go turn it off, then back on and put it on rince and drain, then when that is done it will beep again and i have to turn it off then back on and set it to spin and drain .. It was not doing that before I got the machine filter clean out, What would cause this?
Current Answers
Answer #1: Posted by richsappliance on July 11th, 2014 1:25 PM
richsappliance
Member since:
January 18th, 2014 Points: 91,150
Member since:
January 18th, 2014 Points: 91,150
It may be that you need a new pump. If when you cleaned out the trap for the pump there was alot of stuff in it, something may have got through the trap and either destroyed the impeller. When this happens the machine will take to long to drain, and shut down. Replace the pump. Here is a video on how to replace the pump:
https://www.youtube.com/watch?v=Baezjud-gyg
Check the stored error codes. If you get a F9E1 bad pump. To view the stored error codes do the following:
Starting Service History Mode & Diagnostic Test:
NOTE: The washer must be empty and the control must be
in the OFF state before pressing the touch-pad sequence to
start the test.
1. Close the door.
2. Select any three different keys (except POWER).
Individually press these in a sequence of 1, 2, 3 and then
repeat this sequence two more times. This sequence must
be completed within 8 seconds of the first key press.
These three keys are referred to the 1st, 2nd, and 3rd keys,
based on the order pressed.
3. Upon entry into service diagnostics, the console will beep
(if available) and all console LED lights will turn on for
5 seconds.
4. Any error codes will be displayed in the Estimated Time
Remaining display. If there are no error codes stored,
88 will be displayed. On models without a display, the
WASH LED will flash to indicate the error code. If there
are no error codes stored, the WASH LED remains on.
NOTE: This program recalls the most recent error code first
5. After entry into service diagnostics using the 1st, 2nd, and
3rd keys, each of these keys will have unique functions
regarding service diagnostics as detailed in the following
table:
NOTES:
After the washer displays the first error, additional presses
of the 3rd key will advance through the errors from newest
to oldest. After clearing the error codes, service diagnostics
shows 88 in the display (on models with a display) or WASH
LED remains on (on models without a display) until diagnostic
is exited or any other mode is activated. Diagnostic mode
can be exited by pressing and holding the 1st key for 5
seconds OR by pressing POWER. After the diagnostic test
has finished, unplug washer or disconnect power cord
and wait for 15 seconds. Then plug in washer or reconnect
power.
If I helped you please "ACCEPT" my answer.
Related Amana NFW7300WW Manual Pages
Use and Care - Page 2
... others . Always read and obey all safety messages. This is , tell you how to potential hazards that can happen if the instructions are very important.
WASHER SAFETY
Your safety and the safety of injury, and tell you what the potential hazard is the safety alert symbol. These words mean:
DANGER
You...
Use and Care - Page 3
...You will need
■ A water heater set to deliver 120°F (49°C) water to the washer.
■ A grounded electrical outlet located within...laundry room, closet, or recessed area. Drain hose
G
E.Transport bolt hole plug (4) F. To order, call the toll-free number on soft floor surfaces, such as carpets or surfaces with a maximum slope of the washer. Ask for connecting the drain...
Use and Care - Page 4
...76 mm)
24 in.2 (155 cm2)
1" (25 mm)
301/2"
4"
(775 mm) (102 mm)
A
3" (76 mm)
B
A. Washer only
2" (50 mm)
36" min. (914 mm)
1" (25 mm)
27" (686 mm)
1" (25 mm)
1" (25 mm...4"
(686 mm) (25 mm) (25 mm) (775 mm) (102 mm)
A
B
A. Recessed area B.
Washer on pedestal
301/2" (775 mm)
38" min. (965 mm)
Recommended spacing for custom undercounter installation
The dimensions shown are...
Use and Care - Page 5
... and bottom air openings for cabinet installation
The dimensions shown are required.
7" (178 mm) 7"
(178 mm)
A
B
Laundry tub drain system (view C) The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the washer. The top of the laundry tub must be a minimum of 28" (710 mm) from the bottom of 2" (50 mm).
Floor...
Use and Care - Page 7
... the water lines
■ Run water through the opening of the washer that the rear of the washer is empty and flat washers have been placed into a laundry tub, drainpipe or bucket, to get rid of particles in the water lines that might clog the inlet valve screens.
■ Check the temperature of the water...
Use and Care - Page 8
.... Turn on the water faucets completely and check for air.
■ Do not lay excess hose on the washer.
2.
Hose should be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. See Floor drain under "Tools and Parts."
8 Cold water inlet
1. Attach the cold water hose to reduce the risk of use...
Use and Care - Page 9
... front with the floor.
3. Secure the Drain Hose
Drain hose must be secured to stop the hose from moving the hexagonal plastic part as shown. Move the washer to complete one cycle. Check that all four feet are in firm contact with foam backing, is against the washer cabinet, the washer may end up on the feet...
Use and Care - Page 10
... results. The products will illuminate for approximately the first 7 minutes. The fabric softener is available at the beginning of all wash cycles except Rinse & Spin, Drain & Spin, and Clean Washer with traditional top load machines.
The washer is designed to determine and then provide the amount of water is no agitator, you can handle slow speeds needed for...
Use and Care - Page 11
... completed during operation. First Wash Cycle Without Laundry
Before washing clothes for the selected cycle will illuminate. This initial cycle serves to ensure the interior is normal during the complete installation step, choose the Normal cycle and run it firmly until the lock clicks. To load washer Open the washer door by pressing POWER or Select Cycle button. Overloading can be...
Use and Care - Page 12
... of suds for you do not guess. NOTE: Overfilling could cause garment damage. To begin the wash cycle immediately Press and hold START/PAUSE (for proper use . To power down the washer after the wash cycle is for your laundry products-one is for detergent, one is for liquid chlorine bleach, and one is done and...
Use and Care - Page 13
...then select the desired settings.
Cycles
Wash Cycles
Choose Wash Cycles by pushing the Cycle selector button to shorten drying times.
13 Pausing or Restarting
1. To pause the washer at any time, press START/PAUSE. 2. To continue the cycle, press and hold START/PAUSE (for the selected cycle. Select DRAIN & SPIN. 3. When the spin is pressed.
Cycle
Estimated Temp
Time...
Use and Care - Page 14
... coming from your cold water faucet. Rinse & Spin is illuminated. Drain & Spin
Use this cycle to drain your washer or to thoroughly clean the inside of your wash load. Clean Washer with AFFRESH™ cycle
Use the Clean Washer with strings, and small items such as it stops.
To change an option after starting a cycle anytime before the selected option begins.
Select...
Use and Care - Page 15
...with the washer resulting in component failures and noticeable mold or mildew. Metal objects such as infant socks, in washer errors, longer cycle times and reduced rinsing performance. This wash system,...bag. Remove non-washable trim and ornaments.
■ Empty pockets.
LAUNDRY TIPS
Preparing clothes for washing Follow these recommendations to use.
The package for this type
of the ...
Use and Care - Page 17
... the drawer. 2. NOTE: Do not wash components in the washer. ■ Repeat steps 1, 2, and 6 to wipe up any clothing or items from the softener and bleach
compartments). 3.
NOTE: The basket will rotate, then the door will unlock, lock again, and then the cycle will continue.
■ The machine will not fill, but the basket...
Use and Care - Page 18
... machine must be properly set up for an extended period of time, you are at home.
Because some water may stay in the drum. 2. If storing or moving your washer for... not freeze.
Put 1 qt (1 L) of the washer. 6. Run washer on a Rinse & Spin cycle.
2. Unplug washer or disconnect power. 4. Disconnect water inlet hoses from the drain system and attach to the rear panel of R.V.-type...
Use and Care - Page 19
... against the washer cabinet. Unplug washer or disconnect power. If the problem remains, call for service. As with the floor. Refer to the "Installation Instructions" for leaks.
19 If the sink or drain is opened during the washing, rinsing, or spinning process.
Sink and drainpipe must be secured to the drainpipe or laundry tub. Unplug washer or disconnect...
Use and Care - Page 20
...Wash compartment.
■ Is there water in the same wash cycle repeatedly? Control won't accept selections or won 't power up all High Efficiency washers. Wipe up
WARNING
Electrical Shock Hazard Plug into a grounded 3 prong outlet? Clean the fabric softener dispenser. Select DRAIN & SPIN...details.
■ Are the laundry products in all spills. Washer stops working outlet, and check for...
Use and Care - Page 21
... time to redistribute the load. This ensures a gentle wash for leaks.
■ Are you using the Delicate wash cycle you wash a large load in washer
■ Is the drain hose clogged, or the end of movement).
■ Is the load balanced? Washer won 't drain or spin, water remains in a delicate cycle? See "Level Washer."
■ Has the drawer dispensed detergent? You will...
Use and Care - Page 22
... if overloaded.
■ Check the following: Was paper or tissue left in the drum, and start a Rinse & Spin and Drain & Spin cycle. The wash load must be balanced. Select a cycle with this washer. Powdered detergents may cause imbalance. Unload the washer as soon as it in suspension.
■ Do you are connected to the detergent compartment. Residue, lint...
Dimension Guide - Page 1
... in the top are required.
Recessed or closet installation - See "Tools and Parts." Stacked washer and dryer
48 in.2* (310 cm2)
3" (76 mm)
24 in .2 (310 cm2)
3" (76 mm)
38" min. (965 mm)
Laundry tub drain system (view C) The laundry tub needs a minimum 20 gal. (76 L) capacity. Additional hoses might be a minimum of 28...
Similar Questions
Fabric Softener Dispenser Not Working
My washing machine doesn't dispense fabric softener anymore. At the end of the wash cycle the dispen...
My washing machine doesn't dispense fabric softener anymore. At the end of the wash cycle the dispen...
(Posted by Tkessaram 2 years ago)
Nfw7300ww02 Amana Front Load Washer Will Not Spin Fast.
NFW7300WW02 front load washer will not spin fast enough to remove the water with a normal size load ...
NFW7300WW02 front load washer will not spin fast enough to remove the water with a normal size load ...
(Posted by rtdk 3 years ago)
Washer
The washer seem like it is stuck on draining but there is no lights and the lid is not locked
The washer seem like it is stuck on draining but there is no lights and the lid is not locked
(Posted by Terencejacobs 10 years ago)