3Com 2824 SFP Support Question
3Com 2824 SFP Support Question
Find answers below for this question about 3Com 2824 SFP - Baseline Switch Plus.Need a 3Com 2824 SFP manual? We have 1 online manual for this item!
Current Answers
Related 3Com 2824 SFP Manual Pages
User Guide - Page 5
... Web site:
www.3com.com
Naming Convention
Throughout this guide, the 3Com Baseline Switch 2816/2824-SFP Plus is intended for use by those responsible for installing and setting up network ...system, or device
Warning
Information that are referred to as the Switch. If a release note is shipped with a plus sign (+).
Table 1 Notice Icons
Icon
Notice Type
Description
Information note...
User Guide - Page 6
... about contacting Technical Support, please refer to : ■ Emphasize a point. ■ Denote a new term at :
[email protected]
Please include the following information when commenting: ■ Document title ■ Document part number (on the title page) ■ Page number (if appropriate)
Example: ■ 3Com Baseline Switch 2816-SFP/2824-SFP Plus User
Guide ■...
User Guide - Page 7
... 1000BASE-T ports also support automatic 10/100/1000 Mbps speed detection.
10/100 Mbps connections on the front panel for users who want the high-speed performance of 10/100/1000 switching with the added functionality of the device. It also identifies the contents of the Baseline Switch
The 3Com Baseline Switch 2816-SFP/2824-SFP Plus is shipped ready...
User Guide - Page 8
... Buchsen dürfen an diese Datensteckdosen angeschlossen werden. 8
CHAPTER 1: INTRODUCING THE BASELINE SWITCH
any combination. AVERTISSEMENT: Points d'accès RJ-45. Nur RJ-45-Datenanscluße, Telefonnetzsysteme or Netztelefone an diese Steckdosen anschließen.
The Switch has 16 (2816-SFP) or 24 (2824-SFP) 10/100/1000 Mbps auto-negotiating ports. WARNHINWEIS: RJ-45-Porte...
User Guide - Page 9
... installed in a slot and is active, the associated RJ-45 port of 100 full duplex mode. CAUTION: The Switch supports full duplex auto-negotiation.
supports automatic MDI/MDI-X detection and can be connected to 24 (2824-SFP) on the Green port at 10 or 100 Mbps.
Table 1 10BASE-T/100BASE-TX Ports
Status Meaning
Green The...
User Guide - Page 10
... power status of Status LEDs, which are installed. Off
No fiber SFP is in half-duplex mode. Switch is inserted in progress.
Contact your supplier. Yellow to Green
Off
... fourth (bottom) row of the Switch: Table 4 Power LEDs
Status
Meaning
Green
The unit is operating
in failsafe mode.
10
CHAPTER 1: INTRODUCING THE BASELINE SWITCH
Table 1 10BASE-T/100BASE-TX Ports
Flashing...
User Guide - Page 12
12
CHAPTER 1: INTRODUCING THE BASELINE SWITCH
User Guide - Page 17
... resolve the issue:
■ Check the 3Com Knowledgebase for assistance. Figure 3 Connecting Devices to the Switch
Baseline 10/100 Switch
Endstations on switched 100 Mbps connections
Baseline 10/100 Switch
Endstations on switched 100 Mbps connections
BaselineBSawsietclihne28S1w6i/t2ch82242-5S0FP Plus
1000 Mbps copper or F iber connection to backbone or server/worksation
1000 Mbps link 10...
User Guide - Page 18
...:
1 Hold the transceiver so that the fiber connector is toward you insert an SFP transceiver that is not supported, the Switch will not operate within the Switch.
If the SFP transceiver is correct at the time of publication: ■ 3CSFP91 SFP (SX) ■ 3CSFP92 SFP (LX)
To access the latest list of the following sections describe how...
User Guide - Page 21
... a built-in Web interface that you need to access the Web interface and configure the Switch.
This chapter provides information on 3Com Baseline Switch 2816-SFP/2824-SFP Plus CD-ROM that is supplied with your Switch
■ A computer that is connected to the Switch, insert the CD-ROM into its advanced settings. To use to set the admin...
User Guide - Page 22
... multiple network adapters, select the adapter that appears is complete, the Discovered Devices screen displays detected network devices.
3 On the Discovered Devices screen, click Baseline Switch 2816-SFP/2824-SFP Plus, and then click Next. Logging On to the Web Interface
After the Web interface loads in your Web browser, the first page that connects the...
User Guide - Page 24
... settings of the Switch
Port Configuration Allows you to configure the Switch's port settings
VLANs
Allows you to create VLAN groups, add port members, and specify how VLAN tagging is used
Link... display the context-sensitive help pages provide information on the image. Menu Item Support
Log Out
Description
Displays 3Com contact information and describes how to save and apply any unsaved changes...
User Guide - Page 27
... ■ Changing the Admin Password ■ Modifying the IP Address Settings ■ Configuring Port Settings ■ Configuring VLANs ■ Configuring Link Aggregation ■ Viewing Statistics ■ Mirroring Port Traffic ■ Running Cable Diagnostic ■ Using the System Tools ■ Viewing Support Information
Configuration Overview
The Switch is shipped ready for use.
User Guide - Page 33
... for the port.
Sets the broadcast storm threshold.
Supported SFP transceivers only operate at once, typically with wrong answers... ports are set the
Switch's broadcast storm control and threshold limits.
A If you do not configure the Switch's port settings, the...5000, 10000, and 15000 bytes per packet. Configuring VLANs
33
Figure 13 Advanced Port Configuration Page
Default Port ...
User Guide - Page 36
... you want to add ports 7, 8, and 16 to VLAN2 (as shown in VLAN 2
Baseline Switch 2824-SFP Plus
add another port to "Creating a VLAN" for instructions. VLAN1 is set up a VLAN across two Switches using uplink connections. 36
CHAPTER 4: CONFIGURING THE SWITCH
Figure 16 Desktop VLAN Configuration
Endstations in VLAN 1
Endstations in Figure 16), so that the ports on the default VLAN1...
User Guide - Page 50
...
■ The fiber cable is in good condition.
■ The SFP module is correctly inserted.
■ A 3Com SFP module is being used for 1000BASE-T operation. Ensure that the workstation's network...broadcast operation.
The Firmware image has become corrupted
Category 5 cable is poor
The Switch supports full-duplex auto-negotiation. Category 3 cables can be broadcast storms on the ...
User Guide - Page 57
... the mounting kit supplied
IEC 320 50/60 Hz 100-240 VAC 1 Amp (maximum) 60 W
184.3 BTU/hr B TECHNICAL INFORMATION
Related Standards
The 3Com Baseline Switch 2816/2824-SFP Plus has been designed to the following standards:
Functional
MAC Address Safety EMC Emissions
Immunity
ISO 8802-3, IEEE 802.3 (Ethernet), IEEE 802.3u (Fast Ethernet), IEEE...
User Guide - Page 59
...are of the unit must be carried out by qualified personnel only.
■ If installing the Switch unit in a stack with other units, the Switch unit must be installed below the narrower units and above the deeper units.
■ The ...SAFETY INFORMATION
Important Safety Information
Please read the following safety information carefully before installing the Baseline Switch 2816-SFP/2824-SFP Plus.
User Guide - Page 65
Half duplex is not supported for TCP/IP networks.
Full Duplex
A system that allows packets to be transmitted and ... responsible for providing engineering solutions for 1000 Mbps. In the network management area, this group is responsible for VLANs to communicate across switched networks. Gigabit Ethernet
An Ethernet system that is designed to operate at the same time and, in effect,...
User Guide - Page 68
Originally a UNIX standard, TCP/IP is now supported on almost all platforms, and is the name for two of the most well-known... or connection point in order to share information and resources as though located on the Switch. Traffic Monitoring
Enables the monitoring of the destination network.
A VLAN serves as the address of port traffic by attaching a network analyzer to one piece ...
Similar Questions
Firmware For The Baseline Switch 2250-sfp Plus
Good afternoon. You can send the latest firmware for the Baseline Switch 2250-SFP PlusProduct 3C Num...
Good afternoon. You can send the latest firmware for the Baseline Switch 2250-SFP PlusProduct 3C Num...
(Posted by intel666 3 years ago)
3com Baseline Switch 2816-sfp Plus 3c16485
i got 3com 3c16485 with fail safe mode problem , and cant find firmware to put i found just for 3com...
i got 3com 3c16485 with fail safe mode problem , and cant find firmware to put i found just for 3com...
(Posted by eltawil13 9 years ago)
How To Configure Vlan And Route With Switch 2928 Sfp Plus
Please helpme config me switch 2928 sfp plus or send me a manual user in spanish please thank you
Please helpme config me switch 2928 sfp plus or send me a manual user in spanish please thank you
(Posted by soporte43238 12 years ago)
I Have A 3com Baseline Switch 2928 Sfp Plus (3crbsg2893)
I have a 3Com Baseline Switch 2928 SFP Plus (3crbsg2893), which I set as follows: I have an ADSL int...
I have a 3Com Baseline Switch 2928 SFP Plus (3crbsg2893), which I set as follows: I have an ADSL int...
(Posted by efrainadame 12 years ago)
Can Switch '3com Baseline 2226 Plus' Can Support Ipv6? Please Advice.
Hye All, Im looking for the answer that the 3com switch baseline 2226 plus can support IPV6. Please...
Hye All, Im looking for the answer that the 3com switch baseline 2226 plus can support IPV6. Please...
(Posted by dYaiTa 12 years ago)