Owners Manual
Page 1
... etc. Contact qualified YAMAHA service personnel when any reasons. • Secure placement or installation is liable to clean the speaker with a rated output power higher than the nominal input power of the speaker. The cabinet should be taken never to exceed the speaker's maximum input. • Do not attempt to be opened for any service is needed. PRECAUTIONS Read this before using an amplifier with chemical solvents as...
... etc. Contact qualified YAMAHA service personnel when any reasons. • Secure placement or installation is liable to clean the speaker with a rated output power higher than the nominal input power of the speaker. The cabinet should be taken never to exceed the speaker's maximum input. • Do not attempt to be opened for any service is needed. PRECAUTIONS Read this before using an amplifier with chemical solvents as...
Owners Manual
Page 2
... not install the speaker to a TV set . Determine the best position by following the owner's manual supplied with soft surface material. Tapping screw (3.5-4 mm) (Available at the hardware store) ■ Using as presence or surround speakers Mount the speakers on a wall or place the speakers on a shelf. NS-M325 (Presence) Subwoofer NS-M325 Center (Surround back) 3 mm Min. 20 mm 40 mm Wall/ wall support You can also use the attached mounting bracket). PLACING THE SPEAKERS Place the speakers...
... not install the speaker to a TV set . Determine the best position by following the owner's manual supplied with soft surface material. Tapping screw (3.5-4 mm) (Available at the hardware store) ■ Using as presence or surround speakers Mount the speakers on a wall or place the speakers on a shelf. NS-M325 (Presence) Subwoofer NS-M325 Center (Surround back) 3 mm Min. 20 mm 40 mm Wall/ wall support You can also use the attached mounting bracket). PLACING THE SPEAKERS Place the speakers...
Owners Manual
Page 3
If one side of the amplifier (or receiver) SPEAKERS R +- When using a banana plug Banana plug 3 1 2 1 Remove the cover by twisting the coating off . Tighten Red (+) + NS-M325 NS-M325 (R) (L) Speakers output terminals of the cable. Connect the (-) terminals on both components using one speaker is switched off . 3 Insert the bare wire. 4 Tighten the knob and secure the cables. L A -+ B Amplifier or Receiver ■ CONNECTIONS • Connect the screw-type input terminals at the rear of the speakers to reverse the polarity...
If one side of the amplifier (or receiver) SPEAKERS R +- When using a banana plug Banana plug 3 1 2 1 Remove the cover by twisting the coating off . Tighten Red (+) + NS-M325 NS-M325 (R) (L) Speakers output terminals of the cable. Connect the (-) terminals on both components using one speaker is switched off . 3 Insert the bare wire. 4 Tighten the knob and secure the cables. L A -+ B Amplifier or Receiver ■ CONNECTIONS • Connect the screw-type input terminals at the rear of the speakers to reverse the polarity...
Owners Manual
Page 4
The front cover is attached to remove it. Do not place the front cover close to exceed the input power values noted above. SPECIFICATIONS Type 2-way acoustic suspension speaker system Magnetic shielding type Driver 10 cm (4") cone woofer 3 cm (1") dome tweeter Impedance 6 Ω Frequency Response 65 Hz to 50 kHz (-10d B) Nominal Input Power 30 W Maximum Input Power 120 W Sensitivity 86 dB/2.83 V/m Crossover Frequency 2.5kHz Dimensions (WxHxD 150 x 275 x 175 mm...
The front cover is attached to remove it. Do not place the front cover close to exceed the input power values noted above. SPECIFICATIONS Type 2-way acoustic suspension speaker system Magnetic shielding type Driver 10 cm (4") cone woofer 3 cm (1") dome tweeter Impedance 6 Ω Frequency Response 65 Hz to 50 kHz (-10d B) Nominal Input Power 30 W Maximum Input Power 120 W Sensitivity 86 dB/2.83 V/m Crossover Frequency 2.5kHz Dimensions (WxHxD 150 x 275 x 175 mm...