Owner's Manual
Page 4
... q After unpacking, check that the following accessories are included. used to eliminate undesirable ultra-low-frequency signals (AX-592 and AX-892 only) q PRE OUT/MAIN IN terminals; q Remote Control Transmitter q Batteries (size AA, R6, UM-3) YAMAHA HiFi SYSTEM REMOTE CONTROL TRANSMITTER AUX DIR A DIR B REC/PAUSE PLAY TAPE 2 A/B TAPE 1 PRESET A/B/C/D/E TUNER DISC PLAY...
... q After unpacking, check that the following accessories are included. used to eliminate undesirable ultra-low-frequency signals (AX-592 and AX-892 only) q PRE OUT/MAIN IN terminals; q Remote Control Transmitter q Batteries (size AA, R6, UM-3) YAMAHA HiFi SYSTEM REMOTE CONTROL TRANSMITTER AUX DIR A DIR B REC/PAUSE PLAY TAPE 2 A/B TAPE 1 PRESET A/B/C/D/E TUNER DISC PLAY...
Owner's Manual
Page 10
... level. These terminals are turned off. COPORUUETPLEMIARNIN L R PHONO REMOTE CONTROL (AX-592) PHONO (AX-892) PHONO (MM/MC) switch AX-592 and AX-892 only Select either MM or MC depending on the front panel are for connection...it stays in some cases better results may be connected. REMOTE CONTROL PRE OUT/MAIN IN terminals AX-592 and AX-892 only Removing the jumper pins enables this terminal will be used for overall adjustment of a control amplifier...remove the jumper pins. This connection allows you have a YAMAHA turntable with a terminal for remote control, connect it releases.
... level. These terminals are turned off. COPORUUETPLEMIARNIN L R PHONO REMOTE CONTROL (AX-592) PHONO (AX-892) PHONO (MM/MC) switch AX-592 and AX-892 only Select either MM or MC depending on the front panel are for connection...it stays in some cases better results may be connected. REMOTE CONTROL PRE OUT/MAIN IN terminals AX-592 and AX-892 only Removing the jumper pins enables this terminal will be used for overall adjustment of a control amplifier...remove the jumper pins. This connection allows you have a YAMAHA turntable with a terminal for remote control, connect it releases.
Owner's Manual
Page 14
...tape deck with an automatic reverse function, pressing DIR A will be the same. q DISC is applicable only for a compact disc changer. 4 PLAY/CUT key AX-592 and AX-892 only Press PLAY/CUT to lower the pick-up arm and press it again to the standby mode and vice versa. (In this mode..., the power indicator on and off. KEY FUNCTIONS 1 2 3 YAMAHA HiFi SYSTEM REMOTE CONTROL TRANSMITTER AUX DIR A DIR B REC/PAUSE PLAY TAPE 2 A/B TAPE 1 PRESET A/B/C/D/E TUNER DISC PLAY...
...tape deck with an automatic reverse function, pressing DIR A will be the same. q DISC is applicable only for a compact disc changer. 4 PLAY/CUT key AX-592 and AX-892 only Press PLAY/CUT to lower the pick-up arm and press it again to the standby mode and vice versa. (In this mode..., the power indicator on and off. KEY FUNCTIONS 1 2 3 YAMAHA HiFi SYSTEM REMOTE CONTROL TRANSMITTER AUX DIR A DIR B REC/PAUSE PLAY TAPE 2 A/B TAPE 1 PRESET A/B/C/D/E TUNER DISC PLAY...
Owner's Manual
Page 20
... AC power plug and contact your authorized YAMAHA dealer or service center for help. CAUSE The AC power plug is degraded when listening with this unit. Speaker connections are connected with the headphones connected to the improper position (AX-592 and AX-892 only). The jumpor pins (PRE OUT..."hums". The IMPEDANCE SELECTOR switch on the turntable. Incorrect output cable connections. No connection from the turntable to the proper position (AX-592 and AX-892 only). The LOUDNESS control is distorted while playing a record on the rear panel is too low. The power to the component ...
... AC power plug and contact your authorized YAMAHA dealer or service center for help. CAUSE The AC power plug is degraded when listening with this unit. Speaker connections are connected with the headphones connected to the improper position (AX-592 and AX-892 only). The jumpor pins (PRE OUT..."hums". The IMPEDANCE SELECTOR switch on the turntable. Incorrect output cable connections. No connection from the turntable to the proper position (AX-592 and AX-892 only). The LOUDNESS control is distorted while playing a record on the rear panel is too low. The power to the component ...