Whirlpool WVI51UC6L Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WVI51UC6L manuals!
Problems with Whirlpool WVI51UC6L?
Ask a Question
Free Whirlpool WVI51UC6L manuals!
Problems with Whirlpool WVI51UC6L?
Ask a Question
Popular Whirlpool WVI51UC6L Manual Pages
Owners Manual - Page 1
... UNIQUEMENT. LIB0174089 / W11549251A
Applicable models / Applicable modèles: WVI30330LS, WVI30336LS
FOR RESIDENTIAL USE ONLY. IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. 30" AND 36" (76.2 AND 91.4 CM) ISLAND-MOUNT CANOPY RANGE HOOD
Installation Instructions and Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301...
Owners Manual - Page 2
...4
Tools and Parts 4 Location Requirements 4 Venting Requirements 5 Electrical Requirements 6 INSTALLATION INSTRUCTIONS 7 Prepare Location 7 Assemble Range Hood 8 Install Range Hood 9 Make Electrical Connection 10 Install Duct Covers 11 Complete Installation 12 RANGE HOOD USE 13 Range Hood Controls 13 RANGE HOOD CARE 14 Cleaning 14 WIRING DIAGRAM 15 ASSISTANCE OR SERVICE 16 In the...
Owners Manual - Page 4
... Safety, Title 24, HUD, Part 280) or, when such standard is factory set for use with cooktops with back draft damper installed
Location Requirements
IMPORTANT: Observe all parts are shown must build a support structure behind the left filter on the model/serial/rating plate. For non-vented (recirculating) Installation see "Non-vented (recirculating) Installation" in ceiling and wall...
Owners Manual - Page 5
... replaces the...part of the thermal break. Ceiling height
*For non-vented (recirculating) installations...Service" section to where the vent system enters the heated portion of the vent should be uniform. Plastic or metal foil vent is recommended. Cold Weather Installations An additional back draft damper should be installed...chart. Venting Requirements
(vented models only)
■ Vent system...
Owners Manual - Page 6
... installation ...specified on the model/serial/rating plate...(meters) for specific requirements in conformance with local codes and industry accepted...Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all governing codes and ordinances.
Deflector B. 6" (15.2 cm) round vent
A.
Follow the electrical connector manufacturer's recommended procedure. To order, see the "Assistance or Service...
Owners Manual - Page 7
... to the National Electrical Code or CSA Standards and local codes and ordinances. Select a flat surface for ceiling support structures. Use a pencil to do so can result in back or other injury.
4. Using two or more people to move and install range hood. Upper horizontal support B. 5 x 45 mm screws (#2 Phillips drive)
7 INSTALLATION INSTRUCTIONS
Prepare Location
■ Lay...
Owners Manual - Page 8
...screws. For installation see the In-Line Smart Kit installation instructions. Assemble Range Hood
1. Install transition on top of fire and electric shock, install this range hood to order.
Lower horizontal support
4. A....See the "Assistance or Service" section to the previously installed upper horizontal support. See the "Assistance or Service" section to be installed in a location other than...
Owners Manual - Page 9
...Leveling screws B.
Using 2 or more people, lift the range hood assembly under the structure.
7. Mounting screws
2. NOTE: To make vent installation easier, temporarily remove the deflector from the chimney support bracket and replace after vent section is in place.
4.
Push duct over the exhaust outlet. A A
B
B
A. Seal all connections with vent clamps. Attach...
Owners Manual - Page 11
... covers
11 Assemble the upper duct covers together and install the duct covers around the support frame. A
A
B
A. Secure the upper duct covers together with 2 - 3.5 x 6.5 mm screws. Position so the flanges of the lower duct cover set into the bottom of the upper duct covers.
Install Duct Covers
NOTE: Remove protective film from the duct...
Owners Manual - Page 12
...Range Hood Care" section.
2. Install metal filters. Lower duct covers top clip area
12
D
8. Plastic clips C. Plastic clips (2) B. Position so the flanges of the lower duct cover set into the flanges of the ...circuit breaker has tripped or a household fuse has blown. Use one plastic clip on each side. Set the lower duct cover in place. Lower duct cover (rear) B. If range hood does not...
Owners Manual - Page 13
Louver holes (non-vented [recirculating] installations only)
B. LED lights
E. Press once for ON and again for quiet operation.
Light button B. Blower... hood is complete to remove smoke, cooking vapors, and odors from the kitchen. The hood controls are located on and set the blower minimumspeed and sound level for OFF. Turn the blower on and off .
13 Operating the blower
The ON/OFF...
Owners Manual - Page 14
... metal filter. Remove the filter by making sure the spring release handles are replaceable by a service technician only. Replace metal grease filter.
See "Metal Grease Filter" in spring release handle. 5.... this section. Replacing a LED Lamp
The LED lights are toward the front. Insert aluminum filter into place to secure the charcoal filter to the following instructions. Always wipe...
Owners Manual - Page 16
... the product warranty and provide after -warranty service anywhere in the United States.
■ Features and specifications on our full line of appliances. ■ Referrals to local dealers. ■ Use and maintenance procedures. ■ Accessory and repair parts sales. Accessories
Recirculation Kit (for non-vented installations only) Order Part Number W11548458
Charcoal Filter Kit (for non...
Dimension Guide - Page 1
... replaces the upper chimney shipped with the range hood. D. Ceiling height
* For non-vented (recirculating) installations IMPORTANT:
Minimum distance "X": 24" (61 cm) from electric cooking surface Minimum distance "X": 27" (68.6 cm) from ceiling to change materials and specifications without notice. Plastic or
metal foil vent is available from your dealer or an authorized parts...
Dimension Guide - Page 2
... to improve our products, we reserve the right to change materials and specifications without notice. Specifications subject to change without notice.
Rear Discharge A 90° elbow may...island hood is factory set for venting through the roof or wall. Vent system can be installed immediately above the hood. For complete details, see Installation Instructions packed with product....
Whirlpool WVI51UC6L Reviews
We have not received any reviews for Whirlpool yet.