Installation Instructions
Page 1
... potential hazards that can happen if the instructions are very important. Table of Contents MICROWAVE HOOD COMBINATION SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Remove Cardboard Template 2 Location Requirements 2 Product Dimensions 3 Electrical Requirements 3 INSTALLATION INSTRUCTIONS 4 Remove Mounting Plate 4 Rotate Blower Motor 4 Locate Wall Stud(s 6 Mark Rear Wall 7 Drill Holes in Rear Wall...
... potential hazards that can happen if the instructions are very important. Table of Contents MICROWAVE HOOD COMBINATION SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Remove Cardboard Template 2 Location Requirements 2 Product Dimensions 3 Electrical Requirements 3 INSTALLATION INSTRUCTIONS 4 Remove Mounting Plate 4 Rotate Blower Motor 4 Locate Wall Stud(s 6 Mark Rear Wall 7 Drill Holes in Rear Wall...
Installation Instructions
Page 2
...B C D E FG H A. 1/4-20 x 3" round-head bolts (2) B. 1/4-20 x 3" flat-head bolts (2) C. See "Venting Design Specifications" section. Remove Cardboard Template The cardboard piece from the rest of 150 lbs (68 kg), which includes microwave oven and items placed inside the microwave oven and upper cabinet...wood studs. Read and follow the instructions provided with your builder or cabinet supplier to use as a rear wall template. 1. Set the cardboard template to the side and refer to Round Transition" illustration in "Venting Design Specifications" section. 2 NOTE: The ...
...B C D E FG H A. 1/4-20 x 3" round-head bolts (2) B. 1/4-20 x 3" flat-head bolts (2) C. See "Venting Design Specifications" section. Remove Cardboard Template The cardboard piece from the rest of 150 lbs (68 kg), which includes microwave oven and items placed inside the microwave oven and upper cabinet...wood studs. Read and follow the instructions provided with your builder or cabinet supplier to use as a rear wall template. 1. Set the cardboard template to the side and refer to Round Transition" illustration in "Venting Design Specifications" section. 2 NOTE: The ...
Installation Instructions
Page 7
...damaged or unusable, measure and mark the wall with the dimensions described in one 1/4-20 x 3" round-head bolt with front edge of the cardboard template. D. Using a straightedge, draw the 2 horizontal, level lines through the mounting plate, closest to figures 1 and 2 in "Possible Wall Stud... Configurations" in "Locate Wall Stud(s)" section. Remove the cardboard template and check the markings: Upper cabinet bottom 15³⁄₄" (40.0 cm) Centerline 17¹⁄₄" (43.8 cm) 14¹...
...damaged or unusable, measure and mark the wall with the dimensions described in one 1/4-20 x 3" round-head bolt with front edge of the cardboard template. D. Using a straightedge, draw the 2 horizontal, level lines through the mounting plate, closest to figures 1 and 2 in "Possible Wall Stud... Configurations" in "Locate Wall Stud(s)" section. Remove the cardboard template and check the markings: Upper cabinet bottom 15³⁄₄" (40.0 cm) Centerline 17¹⁄₄" (43.8 cm) 14¹...
Installation Instructions
Page 8
...Remove all lag screws and bolts. Refer to outlet. 2. Refer to points "D" and "E" on the wall. 4. Position mounting plate on the template is level. 4. Prepare Upper Cabinet 1. Insert lag screw(s) into the hole(s) drilled into the remaining end hole. 6. Securely tighten all contents from... the rear wall to illustrations in "Possible Wall Stud Configurations" in Rear Wall" section. 8 Upper-cabinet template D 10" (25.4 cm) F E 10" G (25.4 cm) Mounting plate C. Make sure the 10" (25.4 cm) dimension from upper cabinet...
...Remove all lag screws and bolts. Refer to outlet. 2. Refer to points "D" and "E" on the wall. 4. Position mounting plate on the template is level. 4. Prepare Upper Cabinet 1. Insert lag screw(s) into the hole(s) drilled into the remaining end hole. 6. Securely tighten all contents from... the rear wall to illustrations in "Possible Wall Stud Configurations" in Rear Wall" section. 8 Upper-cabinet template D 10" (25.4 cm) F E 10" G (25.4 cm) Mounting plate C. Make sure the 10" (25.4 cm) dimension from upper cabinet...
Installation Instructions
Page 9
... Weight Hazard Use two or more people, lift microwave oven and hang it on support tabs at the circular shaded area "G" on the template. Place a washer on the template. NOTE: To avoid damage to move and install microwave oven. A B A. This hole is being handled. Metal cabinet B. Cut 3/4" ... the wall, make sure the damper assembly fits easily into the vent in back or other injury. Position the damper assembly on Upper Cabinet Template. 8. Damper assembly C. Cut the 1¹⁄₂" (3.8 cm) diameter hole at the bottom of the microwave oven so that damper blade...
... Weight Hazard Use two or more people, lift microwave oven and hang it on support tabs at the circular shaded area "G" on the template. Place a washer on the template. NOTE: To avoid damage to move and install microwave oven. A B A. This hole is being handled. Metal cabinet B. Cut 3/4" ... the wall, make sure the damper assembly fits easily into the vent in back or other injury. Position the damper assembly on Upper Cabinet Template. 8. Damper assembly C. Cut the 1¹⁄₂" (3.8 cm) diameter hole at the bottom of the microwave oven so that damper blade...
Installation Instructions
Page 12
... transition piece = 5 ft (1.5 m) D. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m) If the existing vent is located behind the door. ■ Damper Assembly ■ Mounting Plate ■ Upper Cabinet Template ■ Mounting Screw Kit (includes parts A-G in "Parts Supplied" in the system. Accessories Filler Panel Kits are available from sticking. Each panel is a list of...
... transition piece = 5 ft (1.5 m) D. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m) If the existing vent is located behind the door. ■ Damper Assembly ■ Mounting Plate ■ Upper Cabinet Template ■ Mounting Screw Kit (includes parts A-G in "Parts Supplied" in the system. Accessories Filler Panel Kits are available from sticking. Each panel is a list of...