Installation Instructions
Page 5
...; Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that specify use with the ground connected to the neutral by a white cover. The fourth (grounding) conductor must be provided at each end of the power supply cable (at the range and at least 4 ft (1.22 m) long... be provided at 250 volts, 40 or 50 amps and investigated for the copper 4-wire power cord are: 40-amp circuit 2 No.-8 conductors 1 No.-10 white neutral 1 No.-8 green grounding If connecting to a 3-wire system: Local codes may permit the use with a UL listed strain relief and be revised so the...
...; Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that specify use with the ground connected to the neutral by a white cover. The fourth (grounding) conductor must be provided at each end of the power supply cable (at the range and at least 4 ft (1.22 m) long... be provided at 250 volts, 40 or 50 amps and investigated for the copper 4-wire power cord are: 40-amp circuit 2 No.-8 conductors 1 No.-10 white neutral 1 No.-8 green grounding If connecting to a 3-wire system: Local codes may permit the use with a UL listed strain relief and be revised so the...
Installation Instructions
Page 9
... A. C D A. Line 2 (red) D D. Connect line 2 (red) and line 1 (black) wires to the center terminal block post with 10-32 hex nuts. 7. Neutral (white) wire E. Securely tighten hex nuts. Ground-link screw C. Terminal block B. A F A E B C E A. 10-32 hex nut B. Ground-link screw C. Tighten strain relief screws...Allow enough slack to easily attach the wiring to the terminal block. Use ³⁄₈" nut driver to connect the neutral (white) wire to the outer terminal block posts with one of range. UL listed strain relief D. Line 1 (black) 6. Tighten ...
... A. C D A. Line 2 (red) D D. Connect line 2 (red) and line 1 (black) wires to the center terminal block post with 10-32 hex nuts. 7. Neutral (white) wire E. Securely tighten hex nuts. Ground-link screw C. Terminal block B. A F A E B C E A. 10-32 hex nut B. Ground-link screw C. Tighten strain relief screws...Allow enough slack to easily attach the wiring to the terminal block. Use ³⁄₈" nut driver to connect the neutral (white) wire to the outer terminal block posts with one of range. UL listed strain relief D. Line 1 (black) 6. Tighten ...
Installation Instructions
Page 10
...(red) wire D. Part of the range. Line 1 (black) wire 4. Use a Phillips screwdriver to line 1 (black), neutral (white), and line 2 (red) wires. Terminal block B. Neutral (white) wire G. A A B B C A. Ground-link screw 2. Setscrew C. Save the ground-link screw and the end of the terminal... lug and insert exposed wire end through the neutral 1. Neutral (white) wire E. The ground wire must not contact any other terminal. 10 Strip the insulation back ³⁄₈" (1.0 cm) from the ...
...(red) wire D. Part of the range. Line 1 (black) wire 4. Use a Phillips screwdriver to line 1 (black), neutral (white), and line 2 (red) wires. Terminal block B. Neutral (white) wire G. A A B B C A. Ground-link screw 2. Setscrew C. Save the ground-link screw and the end of the terminal... lug and insert exposed wire end through the neutral 1. Neutral (white) wire E. The ground wire must not contact any other terminal. 10 Strip the insulation back ³⁄₈" (1.0 cm) from the ...
Installation Instructions
Page 11
Bare (green) ground wire D. Neutral (white) wire F. Connect line 2 (red) and line 1 (black) wires to the terminal block. Securely tighten hex nuts. 9. Allow enough slack to easily attach the wiring to ...-32 hex nuts. 5. Terminal block B. Ground-link screw C. Line 1 (black) wire D C A. 10-32 hex nut B. Use ³⁄₈" nut driver to connect the neutral (white) wire to the terminal block - 20 lbs-in. (2.3 N-m) Wire Awg Torque 8 gauge copper 6 gauge aluminum 25 lbs-in. (2.8 N-m) 35 lbs-in the following Bare Wire...
Bare (green) ground wire D. Neutral (white) wire F. Connect line 2 (red) and line 1 (black) wires to the terminal block. Securely tighten hex nuts. 9. Allow enough slack to easily attach the wiring to ...-32 hex nuts. 5. Terminal block B. Ground-link screw C. Line 1 (black) wire D C A. 10-32 hex nut B. Use ³⁄₈" nut driver to connect the neutral (white) wire to the terminal block - 20 lbs-in. (2.3 N-m) Wire Awg Torque 8 gauge copper 6 gauge aluminum 25 lbs-in. (2.8 N-m) 35 lbs-in the following Bare Wire...