Installation Guide
Page 3
...Check that opens to 1" (25 mm) or hex-head socket wrench 1/4" nut driver (recommended) Wire stripper Caulking gun and compound (new vent installations) Utility knife 3 Front leveling feet with nuts (2) Shipping strap (Not in parts bag. Tools needed: Optional tools: Flat-blade screwdriver #2 Phillips...See "Remove Shipping Strap.") Wood block Ruler or measuring tape Drain hose Silver double-wire hose clamp Tin snips (new vent installations) Adjustable wrench that all parts were included. installation requirements Tools and Parts Gather required tools and parts before starting...
...Check that opens to 1" (25 mm) or hex-head socket wrench 1/4" nut driver (recommended) Wire stripper Caulking gun and compound (new vent installations) Utility knife 3 Front leveling feet with nuts (2) Shipping strap (Not in parts bag. Tools needed: Optional tools: Flat-blade screwdriver #2 Phillips...See "Remove Shipping Strap.") Wood block Ruler or measuring tape Drain hose Silver double-wire hose clamp Tin snips (new vent installations) Adjustable wrench that all parts were included. installation requirements Tools and Parts Gather required tools and parts before starting...
Installation Guide
Page 4
...Kit Part Number 285835 Water faucets beyond reach of the "Washer/Dryer Use and Care Guide." Mobile home installations require metal exhaust system hardware available for your "Use and Care Guide." installation requirements Tools and Parts Parts needed: (Not supplied with washer/dryer) n Vent clamps n Vent elbows... and ductwork Inlet hoses with washer/dryer) Your installation may require additional parts. If you have: You will need: Overhead sewer Standard 20 gal. (76 L) 39" (990 mm) tall ...
...Kit Part Number 285835 Water faucets beyond reach of the "Washer/Dryer Use and Care Guide." Mobile home installations require metal exhaust system hardware available for your "Use and Care Guide." installation requirements Tools and Parts Parts needed: (Not supplied with washer/dryer) n Vent clamps n Vent elbows... and ductwork Inlet hoses with washer/dryer) Your installation may require additional parts. If you have: You will need: Overhead sewer Standard 20 gal. (76 L) 39" (990 mm) tall ...
Installation Guide
Page 5
...of the washer/ dryer. n S pecial provisions must be at temperatures below 32ºF (0ºC). n A level floor with a maximum slope of installation and servicing. n A dditional clearances might not shut off at or below 45°F (7°C). n A sturdy floor to the Manufactured Home Construction...recommended for this washer/dryer. Some water can remain in the washer and can result in longer drying times. n F or closet installation, with equivalent ventilation openings are using a power supply cord, a grounded electrical outlet located within 4 ft (1.2 m) of the ...
...of the washer/ dryer. n S pecial provisions must be at temperatures below 32ºF (0ºC). n A level floor with a maximum slope of installation and servicing. n A dditional clearances might not shut off at or below 45°F (7°C). n A sturdy floor to the Manufactured Home Construction...recommended for this washer/dryer. Some water can remain in the washer and can result in longer drying times. n F or closet installation, with equivalent ventilation openings are using a power supply cord, a grounded electrical outlet located within 4 ft (1.2 m) of the ...
Installation Guide
Page 7
...If you must be at least 39" (990 mm) above floor; IMPORTANT: To avoid siphoning, no higher than 4.5" (113 mm) of washer/dryer. install no more than 96" (2.4 m) from bottom of drain hose should be needed.) Wall standpipe drain system See requirements for a standpipe drain: 2" (51...and an Extension Drain Hose (Part Number 285863) that may be inside standpipe or below the top of washer/dryer. (Additional hoses may be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Laundry tub drain system Minimum capacity: 20 gal. (76 L). Minimum ...
...If you must be at least 39" (990 mm) above floor; IMPORTANT: To avoid siphoning, no higher than 4.5" (113 mm) of washer/dryer. install no more than 96" (2.4 m) from bottom of drain hose should be needed.) Wall standpipe drain system See requirements for a standpipe drain: 2" (51...and an Extension Drain Hose (Part Number 285863) that may be inside standpipe or below the top of washer/dryer. (Additional hoses may be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Laundry tub drain system Minimum capacity: 20 gal. (76 L). Minimum ...
Installation Guide
Page 8
...to have a fuse in ring terminals or spade terminals with flexible metallic conduit. n Do not have the properly grounded outlet installed by a white cover. It is permanently connected to an individual branch circuit. The neutral ground wire is your outlet looks ...conductor must match power supply (4-wire or 3-wire) and be provided. Grounding through the neutral is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor is properly grounded. ...
...to have a fuse in ring terminals or spade terminals with flexible metallic conduit. n Do not have the properly grounded outlet installed by a white cover. It is permanently connected to an individual branch circuit. The neutral ground wire is your outlet looks ...conductor must match power supply (4-wire or 3-wire) and be provided. Grounding through the neutral is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor is properly grounded. ...
Installation Guide
Page 9
... codes standard may be sure that you use Power Supply Cord Replacement Part Number 9831317. A copy of your responsibility: ■■To contact a qualified electrical installer. ■■To be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA. ■■To supply the required 4-wire, single...
... codes standard may be sure that you use Power Supply Cord Replacement Part Number 9831317. A copy of your responsibility: ■■To contact a qualified electrical installer. ■■To be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA. ■■To supply the required 4-wire, single...
Installation Guide
Page 10
... pins on the end of the washer/dryer until the jam nuts touch the washer. Remove the hang tag and pin from the plug end. Install front leveling feet Tilt the washer/dryer forward. NOTE: Do not tighten the nuts until completely removed from washer/dryer. Discard end with a wood block.... 2. Then screw the locknut onto each of the 2 rear legs in an up the front of the washer/dryer. Gently lower the washer/dryer to install leveling feet 1" (25 mm) Do not cut yellow strap. Prepare to the floor. This is level. Tilt the washer/dryer back and remove the wood...
... pins on the end of the washer/dryer until the jam nuts touch the washer. Remove the hang tag and pin from the plug end. Install front leveling feet Tilt the washer/dryer forward. NOTE: Do not tighten the nuts until completely removed from washer/dryer. Discard end with a wood block.... 2. Then screw the locknut onto each of the 2 rear legs in an up the front of the washer/dryer. Gently lower the washer/dryer to install leveling feet 1" (25 mm) Do not cut yellow strap. Prepare to the floor. This is level. Tilt the washer/dryer back and remove the wood...
Installation Guide
Page 17
..." and, if necessary, modify existing vent system to avoid sagging and kinking that may result in reduced airflow and poor performance. ■■Do not install in enclosed walls, ceilings, or floors. ■■The total length should not exceed 73/4 ft. (2.4 m). Do not use plastic or metal foil vent. NOTE...
..." and, if necessary, modify existing vent system to avoid sagging and kinking that may result in reduced airflow and poor performance. ■■Do not install in enclosed walls, ceilings, or floors. ■■The total length should not exceed 73/4 ft. (2.4 m). Do not use plastic or metal foil vent. NOTE...
Installation Guide
Page 18
... (737 mm) to exhaust out the right or left side. Elbow H. Kits are shown. Left- or right-side exhaust installation 18 A B C A. Part Number Descriptions 4396028 Over-the-Top Installation 4396037 0" (0 mm) to 18" (457 mm) Metal vent periscope (For use with dryer vent to wall vent mismatch)...8482; Periscope 279818 4-way vent kit - To cover the hole in the side, one of the following kits for close-clearance alternate installations are possible. Vent system with dryer vent to rear exhaust by using standard offset connections. In Canada, call 1-800-901-2042, or...
... (737 mm) to exhaust out the right or left side. Elbow H. Kits are shown. Left- or right-side exhaust installation 18 A B C A. Part Number Descriptions 4396028 Over-the-Top Installation 4396037 0" (0 mm) to 18" (457 mm) Metal vent periscope (For use with dryer vent to wall vent mismatch)...8482; Periscope 279818 4-way vent kit - To cover the hole in the side, one of the following kits for close-clearance alternate installations are possible. Vent system with dryer vent to rear exhaust by using standard offset connections. In Canada, call 1-800-901-2042, or...
Installation Guide
Page 19
...Connect vent to exhaust hood Vent must not terminate beneath the mobile home. Determine vent length and elbows needed for mobile home installations: The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must fit over the exhaust hood... min. (305 mm) Determine vent path: ■■ Select route that will provide straightest and most direct path outdoors. ■■ Plan installation to use fewest number of elbows and turns. ■■ When using straightest path possible. To determine maximum exhaust length, add one 90º ...
...Connect vent to exhaust hood Vent must not terminate beneath the mobile home. Determine vent length and elbows needed for mobile home installations: The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must fit over the exhaust hood... min. (305 mm) Determine vent path: ■■ Select route that will provide straightest and most direct path outdoors. ■■ Plan installation to use fewest number of elbows and turns. ■■ When using straightest path possible. To determine maximum exhaust length, add one 90º ...
Installation Guide
Page 20
...water. Place drain hose in picture) or over the area marked "CLAMP." Wet the inside standpipe; Remove drain hose form (floor drain installations only) 2. Continue until hose contacts the ribbed stops on bottom of the washer/dryer. IMPORTANT: 4.5" (113 mm) of the silver ... the drain hose. Attach drain hose to drain connector For floor drain installations, you will need additional parts with pliers to the following instructions: IMPORTANT: To ensure proper installation, this procedure must be installed according to open. See "Tools and Parts." Release clamp. 20 Place...
...water. Place drain hose in picture) or over the area marked "CLAMP." Wet the inside standpipe; Remove drain hose form (floor drain installations only) 2. Continue until hose contacts the ribbed stops on bottom of the washer/dryer. IMPORTANT: 4.5" (113 mm) of the silver ... the drain hose. Attach drain hose to drain connector For floor drain installations, you will need additional parts with pliers to the following instructions: IMPORTANT: To ensure proper installation, this procedure must be installed according to open. See "Tools and Parts." Release clamp. 20 Place...
Installation Guide
Page 21
...until it is snug. Use pliers to tighten couplings an additional two-thirds turn . IMPORTANT: To reduce risk of water hoses. Record hose installation or replacement dates for cold water faucet. Do not use tape or sealants on washer. Firmly seat the washers in attaching hoses to washer correctly...bulges, kinks, cuts, wear, or leaks are working in a closet or recessed area: move the washer/dryer into each end of washer/dryer installation. 21 Replace access panel upon completion of the inlet hoses (not provided). NOTE: Both hoses must be connected to water faucets with new inlet hoses...
...until it is snug. Use pliers to tighten couplings an additional two-thirds turn . IMPORTANT: To reduce risk of water hoses. Record hose installation or replacement dates for cold water faucet. Do not use tape or sealants on washer. Firmly seat the washers in attaching hoses to washer correctly...bulges, kinks, cuts, wear, or leaks are working in a closet or recessed area: move the washer/dryer into each end of washer/dryer installation. 21 Replace access panel upon completion of the inlet hoses (not provided). NOTE: Both hoses must be connected to water faucets with new inlet hoses...
Installation Guide
Page 24
q Dispose of detergent and pour it into a grounded 4-prong outlet Complete Installation CHECKLIST q Check that the water faucets are now installed. See "Level Washer/Dryer." In the U.S.A.: q For power supply cord installation, plug into a grounded 4-prong outlet. q Remove the blue protective film on the console and ...use if the washer/dryer should be 2 household fuses or circuit breakers for leaks around faucets and inlet hoses. For direct wire installation, turn off the dryer and check the following : • Controls are set the dryer on the washer/dryer. If there...
q Dispose of detergent and pour it into a grounded 4-prong outlet Complete Installation CHECKLIST q Check that the water faucets are now installed. See "Level Washer/Dryer." In the U.S.A.: q For power supply cord installation, plug into a grounded 4-prong outlet. q Remove the blue protective film on the console and ...use if the washer/dryer should be 2 household fuses or circuit breakers for leaks around faucets and inlet hoses. For direct wire installation, turn off the dryer and check the following : • Controls are set the dryer on the washer/dryer. If there...
Warranty Information
Page 1
...and serial number label located on the duration of implied warranties of God, improper installation, installation not in materials or workmanship that existed when this book and your authorized Whirlpool dealer to repair or replace appliance light bulbs, air filters or water filters. In... labor if this limited warranty. The removal and reinstallation of your home. 7. If you think you on major appliances with Whirlpool published installation instructions. 10. You must be repaired in your major appliance, to instruct you need to correct house wiring or plumbing. ...
...and serial number label located on the duration of implied warranties of God, improper installation, installation not in materials or workmanship that existed when this book and your authorized Whirlpool dealer to repair or replace appliance light bulbs, air filters or water filters. In... labor if this limited warranty. The removal and reinstallation of your home. 7. If you think you on major appliances with Whirlpool published installation instructions. 10. You must be repaired in your major appliance, to instruct you need to correct house wiring or plumbing. ...
Use & Care Guide
Page 4
...complies with these premium accessories. Part Number Accessory: Part Number Accessory 8212614 3404351 3406839 Dryer vent lint brush Drying rack - See "Installation Instructions" for installation accessories. As a result, water levels will be lower, and hot and warm wash temperatures may not be as warm as you ...are designed to maintain cleaning performance while using less water and energy compared to . In Canada call 1-800-901-2042, or visit us at www.whirlpool...
...complies with these premium accessories. Part Number Accessory: Part Number Accessory 8212614 3404351 3406839 Dryer vent lint brush Drying rack - See "Installation Instructions" for installation accessories. As a result, water levels will be lower, and hot and warm wash temperatures may not be as warm as you ...are designed to maintain cleaning performance while using less water and energy compared to . In Canada call 1-800-901-2042, or visit us at www.whirlpool...
Use & Care Guide
Page 5
...good air flow by the customer, regardless of the vent system at least every 2 years. Proper venting will provide optimal energy savings. See "Installation Instructions." n Use no more drying time or when using the drying rack. 5 This sensing occurs throughout the drying cycle and the dryer ... by improper venting are sensed in shrinkage, wrinkling, and static due to efficiently dry laundry. n Clear away items from the entire length of who installed the dryer. n Replace plastic or foil vent material with 4" (102 mm) diameter heavy, rigid vent material. 4" (102 mm) Good air ...
...good air flow by the customer, regardless of the vent system at least every 2 years. Proper venting will provide optimal energy savings. See "Installation Instructions." n Use no more drying time or when using the drying rack. 5 This sensing occurs throughout the drying cycle and the dryer ... by improper venting are sensed in shrinkage, wrinkling, and static due to efficiently dry laundry. n Clear away items from the entire length of who installed the dryer. n Replace plastic or foil vent material with 4" (102 mm) diameter heavy, rigid vent material. 4" (102 mm) Good air ...
Use & Care Guide
Page 15
... sure leveling legs are secure in the dryer. For gas washer/dryers: 1. Unplug or disconnect power to remove lint. Reinstalling the Washer/Dryer Follow the "Installation Instructions" to remove. 2. Wet lint is hard to locate, level, and connect the washer/dryer. 15 Rinse screen with hot water and liquid detergent. Vacation...
... sure leveling legs are secure in the dryer. For gas washer/dryers: 1. Unplug or disconnect power to remove lint. Reinstalling the Washer/Dryer Follow the "Installation Instructions" to remove. 2. Wet lint is hard to locate, level, and connect the washer/dryer. 15 Rinse screen with hot water and liquid detergent. Vacation...
Use & Care Guide
Page 16
... wall of R.V. - Replace the cover and secure with a 10-watt appliance bulb only. WINTER STORAGE CARE IMPORTANT: To avoid damage, install and store washer/dryer where it will be moved during freezing weather, winterize your washer/dryer. If you do not have packing tray, ...washer/dryer is placed in basket and run washer/dryer through a complete cycle to clean washer and remove antifreeze, if used. Refer to "Installation Instructions" to mix antifreeze and remaining water. 3. Plug in washer/dryer or reconnect power. 3. Run washer through the following recommended procedure: To...
... wall of R.V. - Replace the cover and secure with a 10-watt appliance bulb only. WINTER STORAGE CARE IMPORTANT: To avoid damage, install and store washer/dryer where it will be moved during freezing weather, winterize your washer/dryer. If you do not have packing tray, ...washer/dryer is placed in basket and run washer/dryer through a complete cycle to clean washer and remove antifreeze, if used. Refer to "Installation Instructions" to mix antifreeze and remaining water. 3. Plug in washer/dryer or reconnect power. 3. Run washer through the following recommended procedure: To...
Use & Care Guide
Page 17
...the washer. all four fill hose flat washers are removed during the Spin cycle. See "Using Your Washer" for proper installation: Washer not level. http://www.whirlpool.com/help - Washer/dryer may be attached and have not become clogged. See "Level the Washer/Dryer" in loose heaps... sound with floor, and washer/dryer must be necessary to possibly avoid the cost of a clogged sink or drainpipe. Load dry items in "Installation Instructions." Do not tightly pack. Avoid washing single items. See "Cycle Guide" and "Using Your Washer" in washer drain system. Noises Clicking...
...the washer. all four fill hose flat washers are removed during the Spin cycle. See "Using Your Washer" for proper installation: Washer not level. http://www.whirlpool.com/help - Washer/dryer may be attached and have not become clogged. See "Level the Washer/Dryer" in loose heaps... sound with floor, and washer/dryer must be necessary to possibly avoid the cost of a clogged sink or drainpipe. Load dry items in "Installation Instructions." Do not tightly pack. Avoid washing single items. See "Cycle Guide" and "Using Your Washer" in washer drain system. Noises Clicking...
Use & Care Guide
Page 18
... to drainpipe or tub. Load may have been caught in the load, select Spin. to outlet. WASHER cont. In Canada www.whirlpool.ca If you experience Possible Causes Washer not performing as recommended. Cycles with lower spin speeds remove less water than 96" (2.4 m)... above the floor. Use drain hose form installation. opening. Replace any clogs from drain hose. Small items may need to be closed for your garment. Check plumbing for correct drain...
... to drainpipe or tub. Load may have been caught in the load, select Spin. to outlet. WASHER cont. In Canada www.whirlpool.ca If you experience Possible Causes Washer not performing as recommended. Cycles with lower spin speeds remove less water than 96" (2.4 m)... above the floor. Use drain hose form installation. opening. Replace any clogs from drain hose. Small items may need to be closed for your garment. Check plumbing for correct drain...