Whirlpool WED8120HW Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WED8120HW manuals!
Problems with Whirlpool WED8120HW?
Ask a Question
Free Whirlpool WED8120HW manuals!
Problems with Whirlpool WED8120HW?
Ask a Question
Popular Whirlpool WED8120HW Manual Pages
Instrucciones de instalacion - Page 1
... (depending on connector. C heck for Steam Dryers
Instrucciones para la conexión de la manguera de entrada para secadoras con vapor
Instructions de raccordement du tuyau d'arrivée d'eau pour les sécheuses avec vapeur
INSTALLATION REQUIREMENTS
TOOLS AND PARTS Gather the required tools and parts before starting installation. Damage to the coupling can result.
5. Attach...
Dimension Guide - Page 1
White Available WED8120HW - Electric WGD8120HC - Gas
Chrome Shadow Available WED8120HC - ft.
Electric WGD8120HW - Gas
42 5∕16" Height
W11412665A
32 11∕16" Depth
29" Width Dimension Guide
Whirlpool® Front Load Electric/Gas Dryer with Steam Refresh Cycle, Advanced
Moisture Sensing Technology - 8.8 cu.
Owners Manual 1 - Page 2
... installation must be electrically grounded in accordance with local codes, or in this manual and on your appliance.
The dryer must conform with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, Part 1, CSA C22.1.
2
All safety messages will tell you what can happen if the instructions...
Owners Manual 1 - Page 4
... with dryer) Check local codes. Tools needed for all installations:
Tools needed for gas installations:
8" or 10" pipe wrench
8" or 10" adjustable wrench (for purchase from the dealer from whom you purchased your "Quick Reference Guide." The kit should be type SRD or SRDT and be at least 4 ft. (1.22 m) long.
INSTALLATION REQUIREMENTS
TOOLS AND PARTS Gather...
Owners Manual 1 - Page 5
... cm) above floor. ■ Steam models only: Cold water faucets located within 2 ft. (610 mm) of either side of the dryer in the same closet as a dryer. Some codes limit, or do so can be made in your "Quick Reference Guide."
5 Contact your washer's water supply by purchasing the necessary parts noted in .2 3" (155 cm2) (76...
Owners Manual 1 - Page 8
... the phone numbers referenced in the "Assistance or Service" section of the
burner Btu rating shown on the model/serial rating plate for each 1,000 ft. (305 m) increase in accordance with a different gas without consulting your dryer. Gas supply pressure testing ■ The dryer must be installed within six (6) ft. (1.8 m) of your gas company. NOTE...
Owners Manual 1 - Page 16
... accessible to seal all governing codes and ordinances. Louvered Hood Acceptable Style:
Box Hood
Angled Hood
Elbows: ■ 45° elbows provide better airflow than 90° elbows. Rigid metal vent:
■ Recommended for exhausting. Failure to follow these instructions can be fully extended and supported in final dryer location.
■ Remove excess to...
Owners Manual 1 - Page 21
... receive L2 code for certain part replacement or repair.
Continue to remove the dryer door.
If it will not start dryer.
Pinch the hinge latch between two fingers and pull forward. q If you have power supply problem in a running or "ON" position.
• Start button has been pushed firmly.
• Dryer is plugged into place.
3. See "Troubleshooting." Be sure...
Owners Manual - Page 2
... you how to potential hazards that can happen if the instructions are very important. WARNING
You can be electrically grounded in accordance with local codes, or in this manual and on your appliance.
All safety messages will follow instructions. The dryer must conform with local codes, or in the absence of others .
These words mean:
DANGER...
Owners Manual - Page 5
... not tumble properly and automatic sensor cycles may use your washer's water supply by purchasing the necessary parts noted in longer drying times. Space must support dryer weight of 1" (25 mm) under entire dryer. Contact your "Quick Reference Guide."
5 Louvered doors with a door, minimum ventilation
openings in .2 3" (155 cm2) (76 mm)
6"/0"* (152 mm/0 mm)
1" (25...
Owners Manual - Page 8
...-off valve
In the U.S.A.:
An individual manual shut-off valve.
Gas supply pressure testing ■■ The dryer must be disconnected from the gas specified on the model/serial rating plate for opening and closing .
No attempt shall be easy to prevent kinking. Install a shut-off valve must be installed within six (6) ft. (1.8 m) of a qualified...
Owners Manual - Page 21
... level. Then, follow these instructions. Use flat head screw drive to the locked position. Steam Models Only:
q Be sure the water faucets are now installed. Excessive scale buildup may be crushed or blocked.
If your Airflow screen reads "Check Vent", your dryer vent may lead to the need for this problem. See "Troubleshooting." A
A. Insert both sides...
Quick Reference Manual - Page 3
... of Power which will be guided through the dryer and the dryer vent system for Manual Cycles) will indicate that the moisture sensor on the dryer is complete" and will not be displayed. This alert will show "Drying is operating.
Once installed, launch the app and you have any problems or questions, call Whirlpool® Connected Appliances at...
Quick Reference Manual - Page 4
... from dryer.
Failure to Factory settings then perform Factory Reset. Unit will power back on with all models. Read all cycles, settings, and options are available with "Select Language" display message.
*NOTE: See "Cycle Guide" for more information about cycles, settings, and options.
Not all your unit.
4
Do not dry anything flammable on your Manuals for more...
Quick Reference Manual - Page 7
... product dimensions, please see the INSTALLATION AND CARE INSTRUCTIONS MANUAL included with a customer service representative or if you the cost of the following items please visit www.whirlpool.com/owners or in Canada www.whirlpool.ca/owners. REGISTER PRODUCT
SCHEDULE SERVICE
HOW TO'S & FAQS
MANUALS & ADD SERVICE
DOWNLOADS
PLAN
PARTS
ACCESSORIES
To speak with your correspondence...
Whirlpool WED8120HW Reviews
We have not received any reviews for Whirlpool yet.