Owners Manual 1
Page 4
... upturned ends. ■ A UL listed strain relief Parts needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
... upturned ends. ■ A UL listed strain relief Parts needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
Owners Manual 1
Page 5
... 280) or Standard CAN/CSA-Z240 MH. See "Electrical Requirements." ■ Floor must be made in the same closet as a dryer. You may use your washer's water supply by purchasing the necessary parts noted in the top and bottom of the door are for the recommended spacing allowed. ■ Additional spacing...
... 280) or Standard CAN/CSA-Z240 MH. See "Electrical Requirements." ■ Floor must be made in the same closet as a dryer. You may use your washer's water supply by purchasing the necessary parts noted in the top and bottom of the door are for the recommended spacing allowed. ■ Additional spacing...
Owners Manual 1
Page 18
... it is seated on connector. Do not use old hoses. NOTE: Do not overtighten. Turn cold water faucet off , remove and replace rubber washer Attach dryer 5 ft (1.5 m) inlet hose ends to the coupling can catch lint. The dryer must fit over the exhaust hood. Damage to the...and replace with additional two-thirds turn . T ighten couplings Vent must be connected to "Y" connector and tighten couplings 1. Turn cold water off and remove washer inlet hose. Install exhaust hood 12" min. (305 mm) 2. INSTALL VENT SYSTEM 1. Damage to the coupling can result. 4. Attach long hose ...
... it is seated on connector. Do not use old hoses. NOTE: Do not overtighten. Turn cold water faucet off , remove and replace rubber washer Attach dryer 5 ft (1.5 m) inlet hose ends to the coupling can catch lint. The dryer must fit over the exhaust hood. Damage to the...and replace with additional two-thirds turn . T ighten couplings Vent must be connected to "Y" connector and tighten couplings 1. Turn cold water off and remove washer inlet hose. Install exhaust hood 12" min. (305 mm) 2. INSTALL VENT SYSTEM 1. Damage to the coupling can result. 4. Attach long hose ...
Owners Manual
Page 4
... ends. ■■ A UL listed strain relief Parts needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
... ends. ■■ A UL listed strain relief Parts needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
Owners Manual
Page 5
... must be installed in .2 3" (155 cm2) (76 mm) 6"/0"* (152 mm/0 mm) 1" (25 mm) 1"/0"* (25 mm/0 mm) *Recommended/Minimum spacing Mobile home - You may use your washer's water supply by purchasing the necessary parts noted in your "Quick Reference Guide." 5 Spacing for recessed area or closet installation The dimensions shown are for...
... must be installed in .2 3" (155 cm2) (76 mm) 6"/0"* (152 mm/0 mm) 1" (25 mm) 1"/0"* (25 mm/0 mm) *Recommended/Minimum spacing Mobile home - You may use your washer's water supply by purchasing the necessary parts noted in your "Quick Reference Guide." 5 Spacing for recessed area or closet installation The dimensions shown are for...
Owners Manual
Page 18
... water faucet using straightest path possible. T ighten couplings Vent must be connected to "Y" connector and tighten couplings 1. Turn cold water off and remove washer inlet hose. Avoid 90° turns. The dryer must fit over the exhaust hood. Using pliers, tighten the couplings with 4" (102 mm) clamp...-thirds turn . Secure vent to secure vent, because they can catch lint. Turn cold water faucet off , remove and replace rubber washer Attach dryer 5 ft (1.5 m) inlet hose ends to other fastening devices that extend into interior of the 2 ft (0.6 m) inlet hose. Remove old ...
... water faucet using straightest path possible. T ighten couplings Vent must be connected to "Y" connector and tighten couplings 1. Turn cold water off and remove washer inlet hose. Avoid 90° turns. The dryer must fit over the exhaust hood. Using pliers, tighten the couplings with 4" (102 mm) clamp...-thirds turn . Secure vent to secure vent, because they can catch lint. Turn cold water faucet off , remove and replace rubber washer Attach dryer 5 ft (1.5 m) inlet hose ends to other fastening devices that extend into interior of the 2 ft (0.6 m) inlet hose. Remove old ...
Quick Reference Manual
Page 4
... with "Select Language" display message. *NOTE: See "Cycle Guide" for more information about cycles, settings, and options. USING YOUR DRYER WARNING WARNING Fire Hazard No washer can result in death or fire. 1 CLEAN LINT SCREEN 2 LOAD DRYER Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Items...
... with "Select Language" display message. *NOTE: See "Cycle Guide" for more information about cycles, settings, and options. USING YOUR DRYER WARNING WARNING Fire Hazard No washer can result in death or fire. 1 CLEAN LINT SCREEN 2 LOAD DRYER Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Items...