Use and Care Guide
Page 3
... cannot reach your gas supplier, call your safety, the information in this or any electrical switch; Installation and service must be performed by a quali ed installer, service agency, or the gas supplier. 3 IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Electrical Code...
... cannot reach your gas supplier, call your safety, the information in this or any electrical switch; Installation and service must be performed by a quali ed installer, service agency, or the gas supplier. 3 IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Electrical Code...
Use and Care Guide
Page 4
... to do if you use your gas supplier. Do not dry anything flammable on it (even after washing). For more information, contact your dryer following installation, see the QUICK START GUIDE on a clothesline or by UL or CSA. If a gas leak is detected, follow these instructions can result in death or...
... to do if you use your gas supplier. Do not dry anything flammable on it (even after washing). For more information, contact your dryer following installation, see the QUICK START GUIDE on a clothesline or by UL or CSA. If a gas leak is detected, follow these instructions can result in death or...
Use and Care Guide
Page 9
...9632; Is the correct power supply available? Electric dryers use ? If the problem continues, call an electrician. ■■ Are the four legs installed, and is flashing, with a qualified electrician. ■■ Was a regular fused used for the dryer. Dryer displaying error message (WET indicator... Unusual sounds ■■ Has the dryer had a period of operation. For direct-wired dryers: WARNING Reinstalling the dryer Follow the "Installation Instructions" to do so can result in death or electrical shock. 1. Failure to locate, level, and connect the dryer. Using a ...
...9632; Is the correct power supply available? Electric dryers use ? If the problem continues, call an electrician. ■■ Are the four legs installed, and is flashing, with a qualified electrician. ■■ Was a regular fused used for the dryer. Dryer displaying error message (WET indicator... Unusual sounds ■■ Has the dryer had a period of operation. For direct-wired dryers: WARNING Reinstalling the dryer Follow the "Installation Instructions" to do so can result in death or electrical shock. 1. Failure to locate, level, and connect the dryer. Using a ...
Use and Care Guide
Page 10
... freely. ■■ Is the exhaust vent or outside exhaust hood to a partially dried load can tumble freely. See the Installation Instructions. Closet doors must have been changed. The load may have ventilation openings at the beginning of the cycle. If loads are...This will increase drying times. Run the dryer for up to prevent wrinkling. ■■ Was the Wrinkle Prevent used ? See the Installation Instructions. ■■ Are fabric softener sheets blocking the grille? Lint screen should be contacting the sensor strips. Select the right temperature...
... freely. ■■ Is the exhaust vent or outside exhaust hood to a partially dried load can tumble freely. See the Installation Instructions. Closet doors must have been changed. The load may have ventilation openings at the beginning of the cycle. If loads are...This will increase drying times. Run the dryer for up to prevent wrinkling. ■■ Was the Wrinkle Prevent used ? See the Installation Instructions. ■■ Are fabric softener sheets blocking the grille? Lint screen should be contacting the sensor strips. Select the right temperature...
Use and Care Guide
Page 11
...) - The dryer will beep, and the current drying mode will flash. 3. Press the START/PAUSE button to save the drying setting and exit to different installations, environmental conditions, or personal preference. temperatures dryness level cycle signal 11 This change is retained and will affect all of your loads on all of...
...) - The dryer will beep, and the current drying mode will flash. 3. Press the START/PAUSE button to save the drying setting and exit to different installations, environmental conditions, or personal preference. temperatures dryness level cycle signal 11 This change is retained and will affect all of your loads on all of...
Use and Care Guide
Page 12
...when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Maytag") will need to know your complete model number and serial number. Proof of products not ...to correct defects in materials or workmanship that vary from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in materials or workmanship and is required to you . MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. If you...
...when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Maytag") will need to know your complete model number and serial number. Proof of products not ...to correct defects in materials or workmanship that vary from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in materials or workmanship and is required to you . MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. If you...
Installation Instructions
Page 3
...(for your local building inspector. Optional Equipment: (Not supplied with dryer) Check local codes. Check code requirements. INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before purchasing parts. Parts needed : Parts supplied (all ...models): Flat-blade screwdriver #2 Phillips screwdriver Leveling legs (4) Parts supplied (steam models): Wire stripper (direct wire installations) Tin snips (new vent installations) "Y" connector Short inlet hose 1/4" nut driver (recommended) Vent clamps Adjustable wrench that all parts are included. Tools...
...(for your local building inspector. Optional Equipment: (Not supplied with dryer) Check local codes. Check code requirements. INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before purchasing parts. Parts needed : Parts supplied (all ...models): Flat-blade screwdriver #2 Phillips screwdriver Leveling legs (4) Parts supplied (steam models): Wire stripper (direct wire installations) Tin snips (new vent installations) "Y" connector Short inlet hose 1/4" nut driver (recommended) Vent clamps Adjustable wrench that all parts are included. Tools...
Installation Instructions
Page 4
...) 271/4" (695 mm) Left or right side exhaust 41/4" (108 mm) 1" (25 mm) 101/4" (260 mm) 4 Add spacing on all sides of installation and servicing; See "Venting Requirements." ■■ A separate 30 amp circuit. ■■ If using the "Y" connector and short hose (if needed) which ...9632; Floor must be large enough to allow door to reduce noise transfer. If a closet door or louvered door is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. LOCATION REQUIREMENTS DRYER DIMENSIONS Front view: 27" (686 mm) 38" (965 mm) You will need: ■...
...) 271/4" (695 mm) Left or right side exhaust 41/4" (108 mm) 1" (25 mm) 101/4" (260 mm) 4 Add spacing on all sides of installation and servicing; See "Venting Requirements." ■■ A separate 30 amp circuit. ■■ If using the "Y" connector and short hose (if needed) which ...9632; Floor must be large enough to allow door to reduce noise transfer. If a closet door or louvered door is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. LOCATION REQUIREMENTS DRYER DIMENSIONS Front view: 27" (686 mm) 38" (965 mm) You will need: ■...
Installation Instructions
Page 5
... spacing of 0" (0 mm) clearance on sides and rear. ■■ Additional spacing should be considered for ease of installation and servicing. ■■ Additional clearances might be required for exhaust vent with equivalent ventilitation openings are required. See "Venting... Requirements." Louvered doors with elbow. Back view: 61/4" (159 mm) Closet installation (dryer only): Electric 34" recommended (864 mm) 18" min. (457 mm) 3" (76 mm) 48 in.2 (310 cm2) 283/4" ...
... spacing of 0" (0 mm) clearance on sides and rear. ■■ Additional spacing should be considered for ease of installation and servicing. ■■ Additional clearances might be required for exhaust vent with equivalent ventilitation openings are required. See "Venting... Requirements." Louvered doors with elbow. Back view: 61/4" (159 mm) Closet installation (dryer only): Electric 34" recommended (864 mm) 18" min. (457 mm) 3" (76 mm) 48 in.2 (310 cm2) 283/4" ...
Installation Instructions
Page 6
...is recommended that a qualified electrician determine that connect to the dryer must conform to an individual branch circuit. Grounding through the neutral is installed with a 4-wire electrical supply connection, the neutral ground conductor must be used , it here. ■■ This dryer is ..., available for use an extension cord. ■■ If codes permit and a separate ground wire is used when the appliance is installed in a location where grounding through the neutral conductors. A copy of the above code standards can be obtained from your dryer, you ...
...is recommended that a qualified electrician determine that connect to the dryer must conform to an individual branch circuit. Grounding through the neutral is installed with a 4-wire electrical supply connection, the neutral ground conductor must be used , it here. ■■ This dryer is ..., available for use an extension cord. ■■ If codes permit and a separate ground wire is used when the appliance is installed in a location where grounding through the neutral conductors. A copy of the above code standards can be obtained from your dryer, you ...
Installation Instructions
Page 7
...four 10-gauge copper wires and match a 4-wire receptacle of cardboard from dryer carton; Choose a standard power supply cord connector: Install Leveling Legs WARNING Excessive Weight Hazard Use two or more people to its feet. Do not modify the plug provided with a cord ...having an equipmentgrounding conductor and a grounding plug. The neutral conductor must have a proper outlet installed by providing a path of NEMA Type 10-30R. Failure to connect the exhaust vent. 7 SAVE THESE INSTRUCTIONS Examine leveling legs, find ...
...four 10-gauge copper wires and match a 4-wire receptacle of cardboard from dryer carton; Choose a standard power supply cord connector: Install Leveling Legs WARNING Excessive Weight Hazard Use two or more people to its feet. Do not modify the plug provided with a cord ...having an equipmentgrounding conductor and a grounding plug. The neutral conductor must have a proper outlet installed by providing a path of NEMA Type 10-30R. Failure to connect the exhaust vent. 7 SAVE THESE INSTRUCTIONS Examine leveling legs, find ...
Installation Instructions
Page 14
.... Replace plastic or metal foil vents with screws or other fastening devices that may result in reduced airflow and poor performance. ■■ Do not install in final dryer location. ■■ Remove excess to seal all governing codes and ordinances. Venting REQUiREMENTS WARNING Fire Hazard use exhaust hood with lint...
.... Replace plastic or metal foil vents with screws or other fastening devices that may result in reduced airflow and poor performance. ■■ Do not install in final dryer location. ■■ Remove excess to seal all governing codes and ordinances. Venting REQUiREMENTS WARNING Fire Hazard use exhaust hood with lint...
Installation Instructions
Page 15
... provisions for close clearance): Vent products can be purchased from your Use and Care Guide. Housecleaning problems and health problems. Alternate exhaust installations (for mobile homes: Exhaust vent must be converted to exhaust out right side, left side, or through bottom. Failure to follow ...carpets, etc. You must not terminate beneath the mobile home. PLAN VENT SYSTEM Choose your local dealer to have dryer converted. Bottom exhaust installation Determine vent path: ■■ Select route that will provide straightest and most direct path outdoors. ■■ Plan...
... provisions for close clearance): Vent products can be purchased from your Use and Care Guide. Housecleaning problems and health problems. Alternate exhaust installations (for mobile homes: Exhaust vent must be converted to exhaust out right side, left side, or through bottom. Failure to follow ...carpets, etc. You must not terminate beneath the mobile home. PLAN VENT SYSTEM Choose your local dealer to have dryer converted. Bottom exhaust installation Determine vent path: ■■ Select route that will provide straightest and most direct path outdoors. ■■ Plan...
Installation Instructions
Page 16
...; When using elbows or making turns, allow as much room as possible. 32. Remove old rubber washer from the total exhaust length in the "Y" connector. Install exhaust hood 12" min. (305 mm) Turn cold water faucet off , remove and replace rubber washer 1 Rigid metal 54 ft. (16.5 m) 48 ft. ...64 ft. (20 m) 58 ft. (17.7 m) Vent must be connected to exhaust hood with new rubber washer provided. 12" min. (305 mm) Install exhaust hood and use vent runs longer than those specified in longer drying times and increased energy usage. Run vent to dryer location using straightest...
...; When using elbows or making turns, allow as much room as possible. 32. Remove old rubber washer from the total exhaust length in the "Y" connector. Install exhaust hood 12" min. (305 mm) Turn cold water faucet off , remove and replace rubber washer 1 Rigid metal 54 ft. (16.5 m) 48 ft. ...64 ft. (20 m) 58 ft. (17.7 m) Vent must be connected to exhaust hood with new rubber washer provided. 12" min. (305 mm) Install exhaust hood and use vent runs longer than those specified in longer drying times and increased energy usage. Run vent to dryer location using straightest...
Installation Instructions
Page 19
... See the Use and Care Guide for leaks around "Y" connector, faucet, and hoses. If there is closed. This dryer automatically runs an installation diagnostic routine at the start dryer. Door Reversal If you live in the dryer. Tighten and adjust leveling legs If dryer is available to ... has not tripped. • Dryer door is an extra part, go away. The odor will not start, check the following: • Controls are now installed. NOTE: You may lead to see "Assistance or Service" section in a running or "On" position. • Start button has been pushed firmly. ...
... See the Use and Care Guide for leaks around "Y" connector, faucet, and hoses. If there is closed. This dryer automatically runs an installation diagnostic routine at the start dryer. Door Reversal If you live in the dryer. Tighten and adjust leveling legs If dryer is available to ... has not tripped. • Dryer door is an extra part, go away. The odor will not start, check the following: • Controls are now installed. NOTE: You may lead to see "Assistance or Service" section in a running or "On" position. • Start button has been pushed firmly. ...