Westinghouse MT80 ARM20 Support and Manuals
Get Help and Manuals for this Westinghouse item
View All Support Options Below
Free Westinghouse MT80 ARM20 manuals!
Problems with Westinghouse MT80 ARM20?
Ask a Question
Free Westinghouse MT80 ARM20 manuals!
Problems with Westinghouse MT80 ARM20?
Ask a Question
Popular Westinghouse MT80 ARM20 Manual Pages
Installation Instructions - Page 1
ISSUED: 01-17-06 SHEET #: 202-9094-1 Installation and Assembly: Universal Articulating Wall Mount for 20" - 42" Screens
Model: MT80 ARM20
Features:
• Universal design for 20" - 42" flat panel screens • Three tensionable pivot points for extensive adjustment of viewing angle • VESA® 100/...
Installation Instructions - Page 2
...; If mounting to wood wall stud wall construction, make sure that mounting screws are anchored into the center of the
studs. If you obtain and use an assistant or mechanical lifting equipment to install your Westinghouse product until you start installation and assembly. See suggested torque values where applicable within these instructions.
• Make sure that the supporting surface...
Installation Instructions - Page 3
Parts List
Description
Qty. Part #
A wall mount
1 095-0345
B Alligator® anchor
2 590-0097
C .198" ID x .313" OD x .437" H retaining spacer 4 590-5003
D 3/16" allen wrench
1 560-9713
E M4 x .7 x 12 mm phillips ...
Installation Instructions - Page 4
...that the wall will safely support the combined load of the equipment and all attached hardware and components.
1
Remove cord covers from wall arm assembly (A) as shown in figure 1.1. Attach wall mount (A) to wall using two.... Installation to Wood Stud Wall
WARNING
• Make sure that mounting screws are anchored into the center of the studs. WARNING
• Tighten screws so that wall plate...
Installation Instructions - Page 5
... screw. Skip to step 2 on cinder block, verify that wall plate is level, and tighten
all fasteners.
Installation to Solid Concrete and Cinder Block
WARNING
• When installing Westinghouse wall mounts on next page. Cinder block must be supplied by installer.
Tighten all fasteners. If mounting to mount in a solid part of the hole when entering a void or cavity.
•...
Installation Instructions - Page 6
... and adapter plate is still not tightly secured, damage may occur to the Westinghouse
Décor wall mount list on a flat, level surface that all holes are properly aligned, and then
tighten screws using security allen wrench (D). Verify that will support the weight of 10
ISSUED: 01-17-06 SHEET #: 202-9094-1 For additional...
Installation Instructions - Page 7
FOR VESA 200 x 200 MOUNTING PATTERN: Thread two M6 x 12 mm screws (G), leaving .25" exposed thread, into top holes on back of screen. FOR SHARP™ 37" LCD SCREEN MODELS LC-37HV6U AND LC-37HV4U: ....25" exposed thread, into top holes on back of screen. Tighten all four screws. FOR VESA 200 MOUNTING PATTERN: Thread two M4 x 12 mm screws (E), leaving .25" exposed thread, into top holes on ...
Installation Instructions - Page 8
....
TENSION KNOB
fig. 3
Note: Make sure cords have to allow full movement of the arm.
4
Route cords inside arm slots of mount and signal cable(s) through one side of wall mount (A) as shown. CAUTION
• Do not tighten screws with the signal.
Screen may have enough slack to be adjusted to adjust tilt...
Installation Instructions - Page 9
... wrench.
TENSION SCREWS
9 of 10
ISSUED: 01-17-06 SHEET #: 202-9094-1 Do not turn more or less tension is no longer engaged with the mount. WARNING
• Do not remove screw or loosen screw until it is desired in the arm pivot points, do the following:
• To increase tension...
Installation Instructions - Page 10
... authorized by Westinghouse Digital Electronics, (b) the failure to utilize proper packing when returning the product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in material and workmanship, under license. EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. This warranty gives specific legal rights...
Westinghouse MT80 ARM20 Reviews
We have not received any reviews for Westinghouse yet.