Weider 9350hard Drive Sys Support and Manuals
Get Help and Manuals for this Weider item
View All Support Options Below
Free Weider 9350hard Drive Sys manuals!
Problems with Weider 9350hard Drive Sys?
Ask a Question
Free Weider 9350hard Drive Sys manuals!
Problems with Weider 9350hard Drive Sys?
Ask a Question
Popular Weider 9350hard Drive Sys Manual Pages
English Manual - Page 1
... line will guarantee you . Read all safety precautions and instructions in this owner's manual before using this owner's manual for future reference.
MST
0
CAUTION! If you have ...Save this equipment.
PATENT PENDING
d
As a manufacturer, we are missing or damaged parts, we will
provide immediate assistance,
0
free of charge to providing complete customer satisfaction. CUSTOMER HOT ...
English Manual - Page 2
...fall with pre-existing health problems. Read all instructions in this owner's manual and in the accompanying literature...WEIDER assumes no responsibility for persons, over the age of 35 or persons with great force.
9. If you feel pain or dizziness at all parts... YOU BEGIN ASSEMBLY ADJUSTMENT TROUBLE-SHOOTING AND MAINTENANCE CABLING DIAGRAM ORDERING REPLACEMENT PARTS LIMITED WARRANTY
2
3 ...
English Manual - Page 3
... , please note the product model number and serial number before using the WEIDER 9350 Hard Drive System. Before reading further, please look at the drawing below and familiarize yourself with the parts that are labeled.
until 6 p.m.
The serial number can be found on a decal attached to achieve the specific results you for selecting the...
English Manual - Page 4
... up through the Base (15). Attach a Rubber Bumper (9) to the PART IDENTIFICATION CHART accompanying this owner's manual. Before beginning assembly, read each step and look at each side of the...parts of the Rear Upright (17) with a #8-32 x 1" Screw (10) and #8-32 Nut (20).
16 4
1
13 45 102
15 U 1
96 45 102 1
2
108
109
109
.
109
Colla
• , - As you attach them, unless instructed...
English Manual - Page 5
...: The Weight Cable (70) must be on the bottom. 3. Press a Weight Sleeve (117) into the top of each of the thirteen Weights (107) so the "weider" logo is on the side of the Bolts shown in the Base (15).
4
Insert the end of the Weight Cable (70) down into the top...
English Manual - Page 6
... Press/Squat Arm and the Pivot Arm.
Remove the Bolt, the 3/8" Flat Washer (64) and
the two 5/8" x 5/16" Bushings (103) from the indicated 3/8" x 2 3/4" Bolt (55).
Set the Nylock Nut
5
aside-it will be used in the bracket with a 5/16" x 2 1/2" Bolt (14), 5/16" Flat Washer (45) and 5/16" Nylock Nut (4). Align the...
English Manual - Page 9
... (54) to the Large "U"-Bracket (81) on the Arm Frame (41) in the same manner.
17 27
to swivel freely. Set the Arm Frame Bushings, the Arm Frame and the Support Plate (120) on the Arm Frame (41). Do not overtighten the Nylock Nut;
Apply grease to the Large "11'1-Bracket (not...
English Manual - Page 11
....
7-ce
23
4 30
21
19 02
113 22 ~•
11 Align the holes in the Arm Shock can be adjusted. Align one of the three sets of the Large Backrest (30) with a 1/4" x 3/4" Screw
22
(7).
21
Attach the Adjustment Bracket (22) to the Swivel "U"-Bracket with the indicated hole in the Front...
English Manual - Page 13
....
28
Slide a 5" Grip (48) onto each end of all parts are not properly routed, they may be explained in the drawing below.... Make sure that the cables move
smoothly, locate and correct the problem before using the hard drive system, pull the ends of the cables...locations shown in ADJUSTMENT, beginning on page 14 of this owner's manual. The use of the Lat Bar.
48 72
29. Remove the...
English Manual - Page 14
...the bent end of the "L"-Pin is not inserted, the
weight setting will be set - ADJUSTMENT
The instructions below describe how each part of the hard drive system can be used in either the butterfly... aligned with the hole In the Front Upright (19).
Refer to the EXERCISE GUIDE accompanying this owner's manual to different positions in the weight stack. nently attached; Pin (112) to see...
English Manual - Page 17
... end of this owner's manual for information about ordering replacement parts. If the cables cannot be replaced. Locate the adjustment sleeve ...parts.
Adjustment
Screw
69
Ball
Adjustment Sleeve
70
62 108 11 85
' e 116
2r.
17 Replace any worn parts immediately.
TROUBLE-SHOOTING AND MAINTENANCE
Inspect and tighten all parts each time you use solvents. Follow the instructions...
English Manual - Page 20
... Time (excluding holidays).
L. The NHtv1~ of the product (WG93500). The KEY NUMBER and DESCRIPTION of the part(s) from the PART LIST/EXPLODED DRAWING accompanying this manual).
4. No other warranty beyond that specifically set forth above is authorized by a WEIDER authorized service center or for products used for commercial or rental purposes.
SOME STATES DO NOT ALLOW LIMITATIONS...
English Manual - Page 21
... Bolt 95 2 5/16" x 2" Bolt 96 2 2" Outer Cap 97 1 VKR Upright 98 1 Military Press Seat 99 2 1/2" x 15/32" Bushing 100 2 Long Clevis WG93500
R794A
Key No. PART LIST Model No. Qty.
English Manual - Page 22
... 1/4" Nut Weight Sleeve 1/4" x 2 1/4" Bolt 3/8" x 3 1/4" Bolt Support Plate Owner's Manual Exercise Poster Part Identification Chart Part List/Exploded Drawing
Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the owner's manual for information about ordering replacement parts. Part No. 120864 1994 Weider, Inc. Key No.
English Manual - Page 23
...
61 000"- -117
112 107
87
28
12
56
12
7
17
96
41 16
98
10
4
9-S 4 10-1
9 20
93
13
6: 4
45 4
745
10 EXPLODED DRAWING Model No.
Weider 9350hard Drive Sys Reviews
We have not received any reviews for Weider yet.