Viper 320HV Support and Manuals
Get Help and Manuals for this Viper item
Popular Viper 320HV Manual Pages
Owner Manual - Page 2
..., diagnosis, troubleshooting or reinstallation of the unit. i This warranty contains the entire agreement relating to its contents. If warranty service is nontransferable ...INSTALLED, AND SERVICED BY A PROFESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED.
promises to the ORIGINAL PURCHASER to repair or replace (with a comparable reconditioned model...
Owner Manual - Page 3
...specific legal rights, and you have other rights which vary from your dealer:
A clear copy of the sales receipt, showing the following:
➤ Date of purchase ➤ Your full name and address ➤ Authorized dealer's company name and address ➤ Type of alarm installed ➤ Year, make, model...DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ...
Owner Manual - Page 6
... use of this guide prior to weaken,
the LED on the purchase of -the-art vehicle security system. When the battery begins to using your state-of your system, you will notice
reduced operating range when using the remote transmitter.
To access the battery for replacement, remove the rear cover
of trouble-free operation...
Owner Manual - Page 8
...if connected). The trunk release is programmable, making it possible to assign any remote button to any specific receiver function. Transmitter functions
This system is controlled by pressing and holding
for ...Electronics, Inc.
5
Press and hold for Panic alarm.
The remote initially comes programmed with Standard Configuration, but may also be customized by pressing . will only ...
Owner Manual - Page 9
The auxiliary output controls
Using your system
The buttons described in all instructions in this manual correspond to your system can be activated by pressing these buttons simultaneously.
The auxiliary output controls
+ Buttons An optional auxiliary convenience or expansion function that ...
Owner Manual - Page 10
...must be taken to indicate that the status LED is described in detail in a grouped pattern, this manual. If the power door locks are closed . trolled by pressing
for Bypass Notification, Warn away or Full..., the doors will flash twice as fast as it does when the system is armed. The alarm system will close immediately after the ignition has been turned off and the last protected entry has...
Owner Manual - Page 12
...
and repeat the process.
To disarm the system without a transmitter
If your remote transmitter is lost or damaged, you must have waited too long to flash after pressing the
button, the system was triggered in your installer at the time of installation for the location of Valet Switch
© 2004 Directed Electronics, Inc...
Owner Manual - Page 13
...arming and triggering either automatically or with the remote transmitter. The system is bypassed.
➜ Valet® mode
Valet® Mode prevents your installation
dealer. To stop Panic Mode at any ...want chirps to lighter impacts is bypassed if the system is useful when washing or servicing your security
system and attract attention. This feature is armed using the silent arm...
Owner Manual - Page 14
...or exit Valet® Mode by using a transmitter
You can access Valet® Mode either manually or from the remote. Press and release the Valet® button within 10 seconds. The status LED will light...will turn off if you are exiting Valet® Mode.
➜ Valet™ mode using the remote transmitter:
1. Turn the ignition on. 2. Press
again. Open any vehicle door.
2. DRW-35
...
Owner Manual - Page 18
... spaces to identify a particular type of input. ZONE
(Number of LED Flashes)
DESCRIPTION
DEALER-INSTALLED OPTIONS
1
Instant trigger for optional
hood or trunk pins
2
A heavier impact detected by the system to write in the following this set code sequence, the receiver and transmitter stay synchronized, even if the transmitter is used . it only...
Owner Manual - Page 19
....
High frequency
Your system transmits and receives at 434 MHz.
Programming options
Programming options control your system's normal, operational set-up. To resynchro- Enjoy a phenomenal increase in range, even in bold:
➤ Active arming (only with the... normally. ily out of the vehicle.
Most options do not require additional parts, but some may require installation labor.
Owner Manual - Page 21
The alarm system will not monitor the zone inputs for Bypass Notification, Warn away or Full trigger .... Power Locks: This system offers lock outputs that can control some manufacturers' power door lock systems. For other systems, additional parts may be added in motion.
If the factory release is established by initiating the triggered sequence.
An optional relay is active and...
Owner Manual - Page 22
...vehicles, this feature requires that when disarmed, only the driver's door unlocks.
Progressive Unlocking: With electric power door ...installed.)
© 2004 Directed Electronics, Inc.
19 Horn Honk: If connected, the horn will sound if the alarm is available only for fuel-injected, automatictransmission vehicles.)
Installation options
Installation options may require additional parts...
Owner Manual - Page 23
Interior Light Illumination: The interior domelight can be configured to illuminate for 30 seconds after the alarm is disarmed once again.
20
© 2004 Directed Electronics, Inc. If the system is rearmed during that 30-second period, the interior light illumination will terminate until the alarm is disarmed.
Owner Manual - Page 25
Trigger or Triggered Sequence: The "setting off" or "tripping" of the siren sounding and the parking lights flashing for ... switch mounted inside the vehicle, at a location determined by the installer. A triggered sequence consists of the alarm. Zone: A zone is lost or damaged, or can be used to override the alarm when a transmitter is a separate input that operates the various functions...
Viper 320HV Reviews
We have not received any reviews for Viper yet.