Operation Manual
Page 5
... injury associated with snow throwers. Replace if necessary. 13. Tampering with the governor setting can result in accidents, injuries or death. A spark arrestor for gas, oil, etc. Section 2 - Clearing a Clogged Discharge Chute Hand contact with the rotating impeller inside where there is equipped with a spark arrestor meeting applicable local or state...
... injury associated with snow throwers. Replace if necessary. 13. Tampering with the governor setting can result in accidents, injuries or death. A spark arrestor for gas, oil, etc. Section 2 - Clearing a Clogged Discharge Chute Hand contact with the rotating impeller inside where there is equipped with a spark arrestor meeting applicable local or state...
Operation Manual
Page 7
... Operator's Manual covers several models. See Fig. 3-1. It is not necessary to all features in this manual are from the operator's position. Bottle 5W-30 Oil • One Chute Rotation Control (If equip.) • One Engine Operator's Manual Two Ignition Keys One Set of the cables in the chute base. Assembly...
... Operator's Manual covers several models. See Fig. 3-1. It is not necessary to all features in this manual are from the operator's position. Bottle 5W-30 Oil • One Chute Rotation Control (If equip.) • One Engine Operator's Manual Two Ignition Keys One Set of the cables in the chute base. Assembly...
Operation Manual
Page 9
See Fig. 3-7. 5. Section 3 - Slowly pull the recoil starter handle up towards the eye bolt. 4. Slip the recoil starter rope into the eye bolt from the back of the snow thrower. Adding Fuel Refer to the Engine Operator's Manual packed with your snow thrower for information on adding and checking oil. Assembly & Set-Up 9 Securely tighten the eye bolt and handle knob. 3. Set-Up Adding Oil Refer to the Engine Operator's Manual packed with your snow thrower for information on adding fuel.
See Fig. 3-7. 5. Section 3 - Slowly pull the recoil starter handle up towards the eye bolt. 4. Slip the recoil starter rope into the eye bolt from the back of the snow thrower. Adding Fuel Refer to the Engine Operator's Manual packed with your snow thrower for information on adding and checking oil. Assembly & Set-Up 9 Securely tighten the eye bolt and handle knob. 3. Set-Up Adding Oil Refer to the Engine Operator's Manual packed with your snow thrower for information on adding fuel.
Operation Manual
Page 13
...ensure that if the shave plate is adjusted too high, snow may be necessary. spring at the end of the engine. Note that any oil trapped snow thrower for 30 days or longer, follow the starter handle a few times to be used for information on the handles. 3.... is removed. 2. See Fig. 6-1. Insert the cable from the outside as follows: 1. Figure 6-1 Off-Season Storage 4. the instructions below. 5. using a light oil or silicone to replace the belt. Shave Plate To check the adjustment of the spark plug hole 3. If after the adjustment to the auger control...
...ensure that if the shave plate is adjusted too high, snow may be necessary. spring at the end of the engine. Note that any oil trapped snow thrower for 30 days or longer, follow the starter handle a few times to be used for information on the handles. 3.... is removed. 2. See Fig. 6-1. Insert the cable from the outside as follows: 1. Figure 6-1 Off-Season Storage 4. the instructions below. 5. using a light oil or silicone to replace the belt. Shave Plate To check the adjustment of the spark plug hole 3. If after the adjustment to the auger control...
Operation Manual
Page 14
... difficult to pull. 6. Maintenance & Adjustments Remove the three screws that help hold it in step 2. 5. NOTE: An oil drain extension kit is necessary to remove the lower panel. 2. Contact your local Troy-Bilt dealer or contact Troy-Bilt's Customer Support for maintenance and adjustment information on your snow thrower for kit #753-06684. 3. If it...
... difficult to pull. 6. Maintenance & Adjustments Remove the three screws that help hold it in step 2. 5. NOTE: An oil drain extension kit is necessary to remove the lower panel. 2. Contact your local Troy-Bilt dealer or contact Troy-Bilt's Customer Support for maintenance and adjustment information on your snow thrower for kit #753-06684. 3. If it...