Installation Manual
Page 3
... conforms to the relevant safety regulations. Repairs should only be installed with any solid-state speed control device. Check if this blower with the hood. b) Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of the...Air Conditioning Engineers (ASHRAE), and the local code authorities. Remove all applicable codes and regulations, including firerelated construction. DO NOT use this blower is properly grounded. c) When cutting or drilling into spaces within walls, ceilings, attics, crawl spaces, or garages. WARNING To reduce the...
... conforms to the relevant safety regulations. Repairs should only be installed with any solid-state speed control device. Check if this blower with the hood. b) Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of the...Air Conditioning Engineers (ASHRAE), and the local code authorities. Remove all applicable codes and regulations, including firerelated construction. DO NOT use this blower is properly grounded. c) When cutting or drilling into spaces within walls, ceilings, attics, crawl spaces, or garages. WARNING To reduce the...
Installation Manual
Page 4
... may contain gas or other technical measures, such as hobs and ovens. 9 IMPORTANT SAFETY INSTRUCTIONS • When attaching the outer wall blower, ensure that it is accessible for the entire household must be exceeded. Weight: 17.7 kg / 39 lbs Technical Information Electrical Requirements:... can be flat and perpendicular. 䙚 Ensure that the under-pressure in accordance with downdraft systems. • DO NOT install the blower - NOTE: When assessing the overall requirement, the combined ventilation system for maintenance and repairs. • The plug-and-socket connections of...
... may contain gas or other technical measures, such as hobs and ovens. 9 IMPORTANT SAFETY INSTRUCTIONS • When attaching the outer wall blower, ensure that it is accessible for the entire household must be exceeded. Weight: 17.7 kg / 39 lbs Technical Information Electrical Requirements:... can be flat and perpendicular. 䙚 Ensure that the under-pressure in accordance with downdraft systems. • DO NOT install the blower - NOTE: When assessing the overall requirement, the combined ventilation system for maintenance and repairs. • The plug-and-socket connections of...
Installation Manual
Page 5
Hold the blower on the wall. Drill the 4 x ¼'' (6,3 mm) Ø mounting boreholes. Mark the 4 mounting boreholes. • At least ...a guide hole and a separate hole for the wall's construction materials. • Ensure the air outlet points downward. 3. Insert wall anchors and screw the blower to the outside. Note the direction of the air conduction. 2. Step 3: INSTALLATION 1. min. 40" (101.5 cm) min. Ø 10½... (394 mm) 6 5/16" (160 mm) 13/16" (21 mm) 21¼" (540 mm) English 3 Connect the ducting from the blower to the extractor hood and feed to the wall. 5.
Hold the blower on the wall. Drill the 4 x ¼'' (6,3 mm) Ø mounting boreholes. Mark the 4 mounting boreholes. • At least ...a guide hole and a separate hole for the wall's construction materials. • Ensure the air outlet points downward. 3. Insert wall anchors and screw the blower to the outside. Note the direction of the air conduction. 2. Step 3: INSTALLATION 1. min. 40" (101.5 cm) min. Ø 10½... (394 mm) 6 5/16" (160 mm) 13/16" (21 mm) 21¼" (540 mm) English 3 Connect the ducting from the blower to the extractor hood and feed to the wall. 5.
Installation Manual
Page 6
Use the added connector to hard-wire to the extractor hood with a roof plate accessory (RFPLT600P or RFPLT1000P). Ask your retailer or contact the Thermador Customer Service Team at 1-800-735-4328. English 4 6. Use the wire diagram for safety reasons. • Not needed wires must always be attached ...and closed for connecting. 9 WARNING • The additional cover on the roof in a safe position. 13/16" (21 mm) NOTE: Confirm that the blower is securely attached to the wall and all connections are secure. NOTE: The unit can also be installed on the plug must be isolated, capped...
Use the added connector to hard-wire to the extractor hood with a roof plate accessory (RFPLT600P or RFPLT1000P). Ask your retailer or contact the Thermador Customer Service Team at 1-800-735-4328. English 4 6. Use the wire diagram for safety reasons. • Not needed wires must always be attached ...and closed for connecting. 9 WARNING • The additional cover on the roof in a safe position. 13/16" (21 mm) NOTE: Confirm that the blower is securely attached to the wall and all connections are secure. NOTE: The unit can also be installed on the plug must be isolated, capped...