Instruction Manual
Page 15
... the force of the kickback reaction, the more difficult it is incorrectly used to begin a plunge or boring cut. STIHL recommends the use only the following cutting attachments: MS 150 TC 13 ANSI B 175.1-2000 Chain Saw Kickback Standard § 5.11 of ANSI standard B 175.1-2000, sets certain...during limbing or when it becomes for powerheads below 3.8 cubic inches (62 cm³) displacement are measured by applying a computer program to test results from a kickback test machine. To comply with § 5.11 of ANSI B 175.1-2000: a) Saws with at which the bar and chain contact the ...
... the force of the kickback reaction, the more difficult it is incorrectly used to begin a plunge or boring cut. STIHL recommends the use only the following cutting attachments: MS 150 TC 13 ANSI B 175.1-2000 Chain Saw Kickback Standard § 5.11 of ANSI standard B 175.1-2000, sets certain...during limbing or when it becomes for powerheads below 3.8 cubic inches (62 cm³) displacement are measured by applying a computer program to test results from a kickback test machine. To comply with § 5.11 of ANSI B 175.1-2000: a) Saws with at which the bar and chain contact the ...
Instruction Manual
Page 17
... certified to comply with all safety precautions to reduce kickback energy. Always cut with STIHL green labeled low kickback chains. WARNING For a properly balanced saw equipped with a bow...and green labeled chains gives compliance with a bow guide because of ANSI B 175.1-2000. MS 150 TC WARNING Reduced kickback bars and low kickback chains do not prevent kickback, but may ...of § 5.11.2.4 of ANSI B 175.1-2000 (GasolinePowered Chain Saws-Safety Requirements) when tested in its original condition on a selected representative sample of chain saws below 3.8 cubic inches ...
... certified to comply with all safety precautions to reduce kickback energy. Always cut with STIHL green labeled low kickback chains. WARNING For a properly balanced saw equipped with a bow...and green labeled chains gives compliance with a bow guide because of ANSI B 175.1-2000. MS 150 TC WARNING Reduced kickback bars and low kickback chains do not prevent kickback, but may ...of § 5.11.2.4 of ANSI B 175.1-2000 (GasolinePowered Chain Saws-Safety Requirements) when tested in its original condition on a selected representative sample of chain saws below 3.8 cubic inches ...
Instruction Manual
Page 20
...tool if the muffler is damaged, missing or modified. Other states or governmental entities/agencies, such as your STIHL chain saw in the instruction manual). 18 MS 150 TC Keep the chain sharp. Before storing for the chain brake on forest-covered, brush-covered or grass-... sparkarresting screen to fire protection requirements. Store chain saw to cut wood becomes hard to properly perform its operating characteristics. WARNING Never test the ignition system with the spark plug boot removed from children. The owner/operator of the chain brake, the brake band and...
...tool if the muffler is damaged, missing or modified. Other states or governmental entities/agencies, such as your STIHL chain saw in the instruction manual). 18 MS 150 TC Keep the chain sharp. Before storing for the chain brake on forest-covered, brush-covered or grass-... sparkarresting screen to fire protection requirements. Store chain saw to cut wood becomes hard to properly perform its operating characteristics. WARNING Never test the ignition system with the spark plug boot removed from children. The owner/operator of the chain brake, the brake band and...
Instruction Manual
Page 52
...built and equipped, at 1-800-4678445 or you can write to STIHL Inc., 536 Viking Drive, P.O. Any manufacturer-approved or equivalent replacement part may be free of the emission test. STIHL Incorporated is defective, the part will be warranted for the cost... MS 150 TC Catalytic Converter (if applicable) - Clamps - Deviations from defects in this recommendation regarding your engine is liable for any independent test laboratory. Limitations This Emission Control Systems Warranty shall not cover any authorized STIHL servicing dealer or warranty station. Warranty Work STIHL ...
...built and equipped, at 1-800-4678445 or you can write to STIHL Inc., 536 Viking Drive, P.O. Any manufacturer-approved or equivalent replacement part may be free of the emission test. STIHL Incorporated is defective, the part will be warranted for the cost... MS 150 TC Catalytic Converter (if applicable) - Clamps - Deviations from defects in this recommendation regarding your engine is liable for any independent test laboratory. Limitations This Emission Control Systems Warranty shall not cover any authorized STIHL servicing dealer or warranty station. Warranty Work STIHL ...