Service Manual
Page 1
... Transport Mechanism Type TCM-230AWR2/230PWR2 SPECIFICATIONS - COMP ACT DISC DECK RECEIVER 9-928-878-12 2001F0200-1 © 2001.6 Sony Corporation Home Audio Company Shinagawa Tec Service Manual Production Group - 1 - HCD-MDX10 SERVICE MANUAL Ver 1.1 2001. 06 US Model Canadian Model AEP Model UK Model E Model Australian Model HCD-MDX10 is the tuner, deck, CD, MD and amplifier section in...
... Transport Mechanism Type TCM-230AWR2/230PWR2 SPECIFICATIONS - COMP ACT DISC DECK RECEIVER 9-928-878-12 2001F0200-1 © 2001.6 Sony Corporation Home Audio Company Shinagawa Tec Service Manual Production Group - 1 - HCD-MDX10 SERVICE MANUAL Ver 1.1 2001. 06 US Model Canadian Model AEP Model UK Model E Model Australian Model HCD-MDX10 is the tuner, deck, CD, MD and amplifier section in...
Service Manual
Page 29
... 5 (I +3V) and CN110 pin 4 (IOP). 2. Check that the reading of the oscilloscope, and check that the results are performed before replacing parts according to "approximate specifications" to 0.92 mW. 4. Do not rotate the AMS dial. (Write power traverse checking) (Traverse Waveform) A VC Specified Value : Laser power meter reading : 7.0 ± 0.2 mW Digital...
... 5 (I +3V) and CN110 pin 4 (IOP). 2. Check that the reading of the oscilloscope, and check that the results are performed before replacing parts according to "approximate specifications" to 0.92 mW. 4. Do not rotate the AMS dial. (Write power traverse checking) (Traverse Waveform) A VC Specified Value : Laser power meter reading : 7.0 ± 0.2 mW Digital...
Service Manual
Page 32
... varies at all times to display "Measu=@@@.@" (@ is satisfied as much as possible. (Read power traverse adjustment) (Traverse Waveform) A VC B Specification A = B 7. Check that the reading of the laser power meter become "Iop Write". Input the Iop value noted down the digital voltmeter reading...stop the laser emission. (The MENU/NO button is satisfied as much as possible. (Write power traverse adjustment) (Traverse Waveform) A VC B Specification A = B 9. will be displayed for a moment.) 10. Adjust the waveform so that the reading the laser power meter and digital volt ...
... varies at all times to display "Measu=@@@.@" (@ is satisfied as much as possible. (Read power traverse adjustment) (Traverse Waveform) A VC B Specification A = B 7. Check that the reading of the laser power meter become "Iop Write". Input the Iop value noted down the digital voltmeter reading...stop the laser emission. (The MENU/NO button is satisfied as much as possible. (Write power traverse adjustment) (Traverse Waveform) A VC B Specification A = B 9. will be displayed for a moment.) 10. Adjust the waveform so that the reading the laser power meter and digital volt ...
Service Manual
Page 33
...: If the traverse waveform is not clear, connect the oscilloscope as shown in " - - ( )" is satisfied as much as possible. (Traverse Waveform) A VC B Specification A = B 18. Press the MENU/NO button when "C1 = AD = " is imposed automatically. 17. The first four digits indicate the C1 error rate, the ...ADJUSTMENT Adjusting Procedure : 1. Then press the ENTER/YES button. 12. Press the ENTER/YES button and display "EFB = CD". Load a test disk (MDW-74/AU-1). 2. Rotate the AMS dial so that the C1 error rate is as shown in the following figure. In this adjustment, ...
...: If the traverse waveform is not clear, connect the oscilloscope as shown in " - - ( )" is satisfied as much as possible. (Traverse Waveform) A VC B Specification A = B 18. Press the MENU/NO button when "C1 = AD = " is imposed automatically. 17. The first four digits indicate the C1 error rate, the ...ADJUSTMENT Adjusting Procedure : 1. Then press the ENTER/YES button. 12. Press the ENTER/YES button and display "EFB = CD". Load a test disk (MDW-74/AU-1). 2. Rotate the AMS dial so that the C1 error rate is as shown in the following figure. In this adjustment, ...