Smeg SF112U Support and Manuals
Popular Smeg SF112U Manual Pages
Instruction Manual - Page 1
... an authorized technician. READ AND SAVE THESE INSTRUCTIONS - Your safety and the safety of Contents
1 Installation
6
1.1 General installation instructions
6
1.2 Electrical requirements
7
1.3 Electrical connection
8
1.4 Cable replacement
10
1.5 Positioning
10
Important Safety Instructions
WARNING: If the instructions contained in this manual and on the appliance.
Read all the...
Instruction Manual - Page 2
... this manual must be removed.
4 IMPORTANT: Installation and grounding must never be followed to minimize the risk of the installer to any other flammable vapors, liquids or materials near this appliance only for its intended purpose. Observe all instructions • Proper installation is your safety, the instructions contained in a safe place and pass them on
the model...
Instruction Manual - Page 3
... is adequate and conforms with the national ANSI / NFPA 70 ELECTRICAL CODE - Safety instructions
Information
Advice
1. Order of the appliance.
Sort the various items of waste and take them to repair the appliance. • All adjustments and servicing must be performed by qualified installers or service technicians. • Do not leave the packing material around the...
Instruction Manual - Page 4
... with the national ANSI/NFPA 70 ELECTRICAL CODE - All other service procedures should be available on the supply line with installation guidelines specified on the model/serial ID plate. Installation
1 Installation
1.1 General installation instructions
• Proper installation is your oven unless specifically recommended in this manual. Make sure you have everything necessary for...
Instruction Manual - Page 5
... Check with a qualified electrician or service technician if you are not sure whether...connection of grounding lead to neutral lead. EN
Installation
1.2 Electrical requirements
Warning Electrical shock hazard
•...specifications indicated on the appliance. If it is recommended.
7 FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH, FIRE OR ELECTRICAL SHOCK. If local codes...
Instruction Manual - Page 6
... local codes.
Frame grounded by connection of the cabinet.
• Remove the junction box cover, if present.
• Install a ... governing codes and ordinances.
• Copies of the standards listed above may be give priority over these instructions. This...chassis.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH, FIRE OR ELECTRICAL SHOCK. Installation
• Wire size and ...
Instruction Manual - Page 7
... wire connector.
U.S. EN
Installation
U.S.
and Canada installation / 4-wire branch circuit
...• Separate the green or yellow-green wires from the white wires that extend out of the end of the ground wire from the oven to the power supply cable neutral wire (white wire):
• The ground wire must be connected first;
• If local codes...
Instruction Manual - Page 8
...; Failure to do not use the door handle to the diagrams shown in an easily reachable position.
1.4 Cable replacement
Power voltage Danger of the appliance must be located near the appliance and in figures.
Installation
• Connect to access the terminal board.
2. Connect to copper wire, or, if connection is heat resistant...
Instruction Manual - Page 9
...oven.
• Remove the literature contained in the package.
• Remove and set aside racks and other parts from inside the oven.
• Move the oven on the final location of...the covers removed previously.
(back view)
11
EN
Installation
Important instructions
For best results, follow these instructions before and during installation.
• To avoid damage to the floor, place the ...
Instruction Manual - Page 10
Appliance overall dimensions
Installation
(front view)
(top view)
(side view) 12
Instruction Manual - Page 11
Standard installation
Installation
EN
Mounting under countertop (front view)
(side view)
Mounting into a column (front view)
(top view)
mm
in
A
Width of cabinet
min. 603
min. 23 3/4
B
Width ...
Instruction Manual - Page 12
Flush installation
Installation
Mounting under countertop (front view)
(side view)
Mounting into a column (front view)
Cleats...Recommended junction box location
Platform
p 557 x 560 x 5 2115/16 x 221/16 x 3/16
sc
Side Cleat 23 mm - 15/16"
Flush installation requires a platform (p) underneath the unit body.
14
(top view)
mm
in
Width of flush inset cutout
A
603
min. 23 3/4
Width of ...
Smeg SF112U Reviews
Do you have an experience with the Smeg SF112U that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Smeg yet.
Earn 750 points for your review!