Smeg C36GGNU Support and Manuals
Get Help and Manuals for this Smeg item
View All Support Options Below
Free Smeg C36GGNU manuals!
Problems with Smeg C36GGNU?
Ask a Question
Free Smeg C36GGNU manuals!
Problems with Smeg C36GGNU?
Ask a Question
Popular Smeg C36GGNU Manual Pages
User manual - Page 1
... 9 4. WALL ATTACHMENT AND THE ANTI-TIP DEVICE 10 5. INSTRUCTIONS FOR THE USER: these instructions contain user advice, a description of the controls and the correct procedures for cleaning and maintenance of Contents - Table of the appliance.
3 Installation and service must be performed by a qualified installer, service agency or gas supplier. DIMENSION REQUIREMENTS 7 3. ELECTRICAL...
User manual - Page 2
... appliance to LP/Propane gas, see the instructions in the Gas Conversion Kit provided in this manual and on to avoid the risk of this
range can occur if the instructions are not followed. The proper gas supply connection must be the T-handle type. - Installation and repairs must be
held liable for the first time...
User manual - Page 3
... inserted into the appropriate lateral hooks (on the model/ serial ID plate.
Make sure that the anti-tip device is re-engaged when the range is your responsibility.
It is the responsibility of the installer to comply with these installation instructions.
-
This plate is NOT designed for installation in manufactured (mobile) homes or in recreational...
User manual - Page 4
... C22.2 No. 01982 - Improper use only.
- SAVE THESE INSTRUCTIONS
6 latest edition - and all governing codes and ordinances.
-
Do not obstruct oven vents or openings for the first time.
- If the appliance does not work properly, disconnect it for damage caused by qualified installers or service technicians.
-
Read all the appliance controls are in this...
User manual - Page 5
DIMENSION REQUIREMENTS
MODEL C24GGXU C36GGXU
CLEARANCE
A
B
C(5)
G(3)
I(4)
L(1)
M(2)
N
612 mm 24 "
636 mm 25 "
216 mm 8 1/2 "
612 mm 24... 11 7/8" (300 mm) from the left rear corner of an unprotected wood or metal cabinet.
2 max. Instructions for the installer 2. cabinet opening width; 4 upper cabinet to side wall or other combustible material;
clearance between the top of ...
User manual - Page 6
....
Some cabinet and building materials are the minimum clearances. An air curtain or other damage. Instructions for combination use. A B C D
60 mm - 2 3/8 " 698 mm - 27 ...problems with ANSI Z21.1 and listed by blowing a downward airflow onto a range, shall not be used . NOTE: Observe all governing codes and ordinances. The indicated dimensions are not designed to be installed...
User manual - Page 7
..., never use the specific leveling legs provided by...installed near to the weight, a dolly/fork lift with soft rubber tread wheels should be used . - Keep the unit raised so the legs can be removed to any undue strain. Instructions ... appliance must be supported uniformly across the bottom. - NOTE: this , screw or unscrew the second part of the screw is designed as a cooking appliance.
User manual - Page 8
... tip the range and be concealed electrical wiring located behind the wall or under the floor.
- Contact a qualified installer or contractor to determine the proper method for the installer
4.
Failure to follow these instructions may result in damage to follow these circuits.
- Do not operate the range without the anti-tip device in...
User manual - Page 9
...C24GGXU (23 15/16 " - 608 mm)
C36GGXU (35 3/4 " - 908 mm)
11 Respect the heights indicated in the installation instructions and the range has been leveled. 1 Level the range using an appropriate fastener (for example, screws appropriate for the type of... the height of screw recommended 1/4"). This notch corresponds to the rear wall as a guide. (Type of the notch found on the bracket.
User manual - Page 10
Instructions for the installer
C24GGXU (23 15/16 " - 608 mm)
C36GGXU (35 3/4 " - 908 mm)
(Front view)
(Front view)
4 Correctly position the range so that the two screws perfectly align with the anti-tip brackets on the range.
12
User manual - Page 12
The anti-tip device works properly only if the bracket attachment is securely anchored to the appliance
14 Instructions for the installer
4 Lower the bracket attachment until anchoring the appliance slot, tighten the nuts previously assembled.
User manual - Page 13
... sure whether the range is recommended that the power line rating matches the specifications indicated on the ID plate located on the back of the standards listed above...have a properly polarized and grounded 3-prong outlet installed by a qualified electrician.
- Instructions for the installer
5. Do not cut or remove the grounding prong.
- lf codes permit and a separate grounding wire is used,...
User manual - Page 14
...codes,
1) installation must conform to American National Standard, National Fuel Gas Code ANSI Z223.1 -
If local codes permit, a flexible metal appliance conductor with all gas connections.
- The pressure regulator has 3/8" female pipe threads. WARNING
- Securely tighten all local codes... installation ... Observe all governing codes and ordinances. ... supply. Instructions for connecting...
User manual - Page 15
.../ E) must be fitted with an approved shut-off valve. Replace the parts on the burner and turn the knobs on the back of ...LEAKS WITH A MATCH OR OTHER FLAMES. The valve is necessary for the installer
Gas connection Connect the adapter C (ISO 228/1 - ½ NPT... arrow on the gas tap valves. Test the appliance Follow these instructions to leak test the appliance: Use a brush and liquid detergent ...
User manual - Page 16
...piping system by closing the respective manual shut-off valve during any pressure... be as follows for the installer
Incoming line pressure upstream from the regulator must be 1" (2.5 cm) W.C.P. LP GAS: Set pressure to 4" W.C.P. Testing ...to check the regulator. maximum. Instructions for operation and checking the regulator setting: - Line pressure testing: Testing above 112 PSI (3.5 kPa...
Smeg C36GGNU Reviews
We have not received any reviews for Smeg yet.