Sharp UN552VS/UN552VS-TMX4P Support and Manuals
Get Help and Manuals for this Sharp item
This item is in your list!
View All Support Options Below
Free Sharp UN552VS/UN552VS-TMX4P manuals!
Problems with Sharp UN552VS/UN552VS-TMX4P?
Ask a Question
Free Sharp UN552VS/UN552VS-TMX4P manuals!
Problems with Sharp UN552VS/UN552VS-TMX4P?
Ask a Question
Popular Sharp UN552VS/UN552VS-TMX4P Manual Pages
External Control Codes for the - Page 6
... (3) Baud rate (4) Data length (5) Parity (6) Stop bit (7) Communication code
Asynchronous RS-232C 9600bps 8bits None 1 bit ASCII
3.2 LAN control
(1) Communication system (2) Interface (3) Communication layer
(4) IP address
(5) Port No. And the controller (PC) has to re-connect to change, Please refer "Network settings" on User's manual. 7142 (Fixed)
(Note) The monitor will disconnect the...
External Control Codes for the - Page 10
...for a confirmation of the "Get current parameter" is as follows,
STX Result OP code OP code
Type
Max value
Requested setting
ETX
page
Value
Hi Lo Hi Lo Hi Lo Hi Lo MSB
LSB
MSB
LSB...message" is used for some non-slider controls and some special operations, such as follows,
STX OP code OP code
Set Value
ETX
page
Hi Lo Hi Lo MSB
LSB
Refer to the section 4.1 "Header block...
External Control Codes for the - Page 22
...Result code. Message STX (02h): Start of Message
Check code BCC: Block Check Code Refer to support this byte is set to change the "Backlight" setting. Delimiter CR (0Dh): End of Message
Check code
...
Check code BCC
Delimiter CR
Header SOH (01h): Start of "Get
parameter", "Set parameter" and "Save current settings".
6.1. IV.
No error. '0'-'0' (30h, 30h): Operation code page ...
External Control Codes for the - Page 23
... packet
Step 3.
No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is the controller. BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Header
Message
SOH-'0'-'0'- Ex.) When this byte is set to change a setting. Delimiter CR (0Dh): End of Message
Check code BCC: Block Check Code Refer to the section...
External Control Codes for the - Page 25
...code
BCC
Delimiter CR
Header SOH (01h): Start of Message
(25/139) No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code...This operation is "Set parameter" type. '0'-'0'-'0'-'3' (30h, 30h, 30h, 33h): Number of Message
Check code BCC: Block Check Code Refer to 'A', the replying Monitor ID is '1'. 'F' (46h): Message Type is "Set parameter reply". ...
External Control Codes for the - Page 26
... is "Set parameter" type. 'F'-'F'-'F'-'F' (46h, 46h, 46h, 46h): Maximum value. '0'-'0'-'3'-'2' (30h, 30h, 33h, 32h): The temperature is the controller.
Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'C' (43h): Message Type is "Get parameter". '0'-'6' (30h, 36h): Message length is 79h (in the page 2). No error. '0'-'2' (30h, 32h): Operation code page...
External Control Codes for the - Page 42
...
POWER
Item FORCE QUIT
SLOT2 CH SETTING
SLOT2 CH SELECT RESET (OPTION)
MODEL NAME SERIAL CARBON SAVINGS
CARBON USAGE
FIRMWARE MAC ADDRESS FACTORY RESET
POWER SUPPLY AUTO POWER ON SETTING LOCK USB BOOT MODE IR SIGNAL MONITOR CONTROL SHUTDOWN SIGNAL POWER OFF DELAY
WDT START UP TIME
OP code OP code
page
10h
C3h
11h
62h...
External Control Codes for the - Page 48
... Ex.) The byte data 20h is 32bytes. Header
SOH-'0'-'0'-Monitor ID'B'-'0'-'E'
Message
STX-'0'-'0'-'C'-'2'-'0'-'3'-'D'-'6''0'-'0'-'0'-'1'-ETX
Check code
BCC
Delimiter CR
Header SOH (01h): Start of Message
Check code BCC: Block Check Code Refer to change a setting. No error. 'C'-'2','0'-'3'-'D'-'6' (43h, 32h, 30h, 33h, 44h, 36h): power control reply command The monitor replies same...
External Control Codes for the - Page 51
... data length that can be written to the monitor at a time is the controller. No error. 'C'-'0'-'0'-'E' (43h, 30h, 30h, 45h): Asset Data write command '0'-'0'(30h, 30h): Offset ...End of Message
Check code BCC: Block Check Code Refer to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command".
Ex.) When this byte is set to the section 4.3 "Check code" for a BCC ...
External Control Codes for the - Page 87
...(01h): Start of Message
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of Message
Check code BCC: Block Check Code Refer to the controller.
FFFFh...
1) The controller requests the monitor to get Model Name. Direct TV Chanel Read & Write
When DTV unit (Option unit) is installed, channel settings is the controller.
External Control Codes for the - Page 88
... want to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is set to get Model Name. Monitor ID: Indicate a replying Monitor ID. Ex.) When this byte is ...32h, 44h): Direct TV Channel write command MajorCH: Major Channel (00000000h - Header
Message
Check code Delimiter
SOH-'0'-Monitor ID-
FFFFh), '0'-'0'-'0'-'0' - 'F'-'F'-'F'-'F' ETX (03h): End of Message 'C'-'3'-'2'-'D' (...
External Control Codes for the - Page 103
...0Dh): End of which you want to change a setting. Auto Tile Matrix
21.1 Auto Tile Matrix Execute
...: 01h (30h, 31h)
ETX (03h): End of Message
Check code BCC: Block Check Code Refer to execute Auto Tile Matrix
Header
SOH-'0'-Monitor ID'0'-'A'-'1'-'2'
Message
STX-'C'-'A'-'0'-'3'-'0'-'1'HM-VM-PID-...to activate the Auto Tile Matrix Setup.
1) The controller requests the monitor to the section 4.3 "Check...
External Control Codes for the - Page 105
...): Start of Message 'C'-'B'-'0'-'3' (43h, 42h, 30h, 33h): Auto Tile Matrix Command '0'-'2' (30h, 32h): Notify ST: Error Status
No Error : 00h (30h, 30h) *Fixed ETX (03h): End of Message
Check code
BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet
(105/139) Header
SOH-'0'-Monitor ID...
External Control Codes for the - Page 108
... Tile Matrix '0'-'6' (30h, 36h): Off ST: Error Status
No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX (03h): End of Message
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet
(108/139)
Ex.) When this byte is set to 'A', replying monitor's ID is '1'. 'B' (42h...
External Control Codes for the - Page 121
...code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of Message
Check code
BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Ex.) When this byte is set... (43h, 42h, 30h, 39h): Setting Copy Reply '0'-'2' (30h, 30h): Start ST: Status
No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX (03h):...
Sharp UN552VS/UN552VS-TMX4P Reviews
Do you have an experience with the Sharp UN552VS/UN552VS-TMX4P that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Sharp yet.
Earn 750 points for your review!