Sharp MX-GBCP3 Support and Manuals
Get Help and Manuals for this Sharp item
This item is in your list!
View All Support Options Below
Free Sharp MX-GBCP3 manuals!
Problems with Sharp MX-GBCP3?
Ask a Question
Free Sharp MX-GBCP3 manuals!
Problems with Sharp MX-GBCP3?
Ask a Question
Popular Sharp MX-GBCP3 Manual Pages
SmartPunch Plus User Manual - Page 2
SmartPunch Plus
Please read these instructions carefully and keep them in a safe place for future reference.
SmartPunch Plus User Manual - Page 3
... THE MACHINE. NEVER remove the screwed-on the end of the cordset (if provided) of the machine operation instructions (also listed on the serial number label). SmartPunch Plus
GB
5. USER DISPLAY
7
6. SPECIFICATIONS
9
8. DIE SET USER MANUAL
10
Important safeguards
i Use the SmartPunch Plus only for its intended purpose of punching, creasing, & perforating paper and...
SmartPunch Plus User Manual - Page 4
...repairs or major maintenance for instructions on hand to the aforementioned conditions, no more than the
minimum specified electrical ratings may be substituted. Operation of this oil will enable you have extra die sets on servicing the Diesets. Service... radiate radio frequency energy and, if not installed and used beyond its specifications. Service, Diesets
Every dieset is used in a ...
SmartPunch Plus User Manual - Page 5
... Double Punch): This operation will now function in the center of holes- SmartPunch Plus will now function in Center Crease mode . D. QUICK START GUIDE
SmartPunch Plus must be inserted before running punch mode.
Die Set User Manual.
SmartPunch Plus will now function in Double Punch mode. See section 4.A for configuration.
The perforation die...
SmartPunch Plus User Manual - Page 6
...INSTALLING DIE SETS IN YOUR SMARTPUNCH PLUS, ALWAYS KEEP FINGERS AND OTHER BODY PARTS OUT OF THE MACHINE'S DIE SET SLOT AND AWAY FROM ALL AREAS OF THE DIE SET...Sets from the Machine: The inter-changeable die set firmly until the Die stop as shown indicated in the CCW direction, as the following instructions illustrate: Note: For advanced Die Set Configuration instructions...removed, supporting it ...
SmartPunch Plus User Manual - Page 7
...the magnet on the Smartpunch Plus are cleared of range for the die or mode installed in and remove the jammed paper. Chip tray Full
When the punch container becomes ...displayed. 7. When this manual titled PAPER CLEARING for crease or perforation. See the section of this message is jammed. Our of Range Adjustment The settings on the right side. To close the paper guide, raise the handle to...
SmartPunch Plus User Manual - Page 8
... is inserted
i)
Alignment
Alignment is the total number of sheets punched with the currently installed die set outside the allowable range for Large (L) and Extra Large (XL) sheets.
MID L... modify this setting. Firmware This displays the current level of Main & Communication (Comm) firmware of adjustment depending on the paper size being sent is type of die set outside the allowable...
SmartPunch Plus User Manual - Page 9
... die for a specific sheet size
Sheet jamming repeatedly at die set , inspect the die throat to see if there is not compatible with the edge of machine or not properly plugged into the wall.
Assembled in Taiwan
Table 1.
Make efforts to reduce curl to back of the paper
Follow instructions on the Make...
SmartPunch Plus User Manual - Page 10
... UI
Crease
Middle Book
Crease die Crease die
Crease (Middle) Setting Mismatch
Setting Mismatch Crease (Book)
C-Fold Crease die Setting Mismatch
Crease (C-Fold)
Perf
Middle Perf die
Perf (Middle)
Setting Mismatch
Single Perf die
Setting Mismatch
Perf (Single)
Double Perf die
Setting Mismatch
Perf (Double)
Setting Mismatch appears when the GBC Punch button on the printer is...
SmartPunch Plus User Manual - Page 11
...
Figure 8.4 Replace Pressure Bar Replace the pressure ...set into the machine or serious damage can accept.
Important! DIE SET USER MANUAL
The SmartPunch Plus accepts Punch, Crease and Perforation dies. Remove the pressure bar and set to inserting the die set...8.1 Pin Removal Guide
The above chart shows ...set aside. Figure 8.2 Pressure Bar Removal Pin Removal
US Paper Sizes GBC Part...
SmartPunch Plus User Manual - Page 12
... arrow on the die stop knob points to clean this occurs, the die set pins that do not over saturate. 3. To lubricate die set must be replaced with the side arrow on the die stop position B
Table 8.2 Die Stop Position Guide
SmartPunch Plus
GB
Die Stop Knob
Position B
Die Stop Handle Label
Position A
Figure...
SmartPunch Plus User Manual - Page 13
.... Oval; 4 Holes per inch; By selecting the appropriate die set, you to -Center Hole Spacing: 6.3mm (0.2475")
For Velo® Bind:
VB Velobind®; Center-to-Center Hole Spacing: 14.3mm (0.563")
Sharp Part Number
Die, Comb Bind Die, Comb Bind, HD
MX-GBCP19 MX-GBCP51HD
* When the Plastic Comb binding die is used in...
SmartPunch Plus User Manual - Page 14
...Perforation Die Cleaning
Media being creased or perforated may become smeared by inserting a tool such as service parts. If this manual to release it fall into the machine.
5. To clean the die: 1. Take care not ...toner marking on the sheet. Unscrew the 2 knurled screws from the input sheet guide and remove the input sheet guide. Do not use a metal pointed tip to damage the chip located at ...
Specification Sheet - Page 1
... panel or print driver. Enhanced capability for new applications and added value for off-line manual punching, creasing,...for up print workflows. Additionally, with a simple die set change! Maximize Productivity
With the seamless integration provided by... and an MX-M1056/M1206 model, you the flexibility to prepare ready-to -bind professional documents. Two-up punch capability supports popular two-...
Specification Sheet - Page 2
... specifications subject to 140 lb. The GBC SmartPunch Plus System makes it easy to produce ready-to-bind documents. cover (75-300gsm) Max. 70 dBA 17.52" (w) x 39.37" (h) x 28.75" (d) 210 lbs. 115 VAC, 4.2 Amps, 60 hz
MAIN UNIT MX-GBCP3
GBC SmartPunch Plus
DIE SETS MX-GBCP19 MX-GBCP51HD MX-GBCP32SQ MX-GBCP21SQ MX-GBCP32RND MX-GBCP21RND MX-GBCP44RND MX...
Sharp MX-GBCP3 Reviews
Do you have an experience with the Sharp MX-GBCP3 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Sharp yet.
Earn 750 points for your review!