Sharp KB-0333K Support and Manuals
Get Help and Manuals for this Sharp item
This item is in your list!
View All Support Options Below
Free Sharp KB-0333K manuals!
Problems with Sharp KB-0333K?
Ask a Question
Free Sharp KB-0333K manuals!
Problems with Sharp KB-0333K?
Ask a Question
Popular Sharp KB-0333K Manual Pages
KB-0333K Operation Manual / Installation Instructions - Page 1
1
1
"
KB-0333K
&OLLOWEDBYINDICATINGCOLOR+BLACK 7WHITE 3STAINLESSSTEEL
INSIGHT RANGE HOOD
",Ê
1
" -1 7,, /9 1
9Ê -/,1
x n
"
/Ê7 n
" 1
1
KB-0333K Operation Manual / Installation Instructions - Page 2
...(including area code) and description of the problem. MODEL NUMBER DATE OF PURCHASE DEALER SERVICER
/
/
SERIAL NUMBER
TELEPHONE TELEPHONE
TO PHONE:
DIAL DIAL
1-800-BE-SHARP (237-4277) for: SERVICE (for your nearest Sharp Authorized Servicer) PARTS (for future reference.
TO ACCESS INTERNET: www.sharpusa.com
2 FOR CUSTOMER ASSISTANCE
To aid in reporting this range hood, please record...
KB-0333K Operation Manual / Installation Instructions - Page 3
... law.
To find the location of purchase to Sharp's Installation Instructions. In order to enforce the rights under this information available when you need service for your range hood.
3
Be sure to contact you . If it will, at its option, either repair the defect or replace the defective Product or part thereof with respect to the Product, and shall...
KB-0333K Operation Manual / Installation Instructions - Page 4
.... To reduce the risk of the surface element.
4
Refer to operate it started.
Installer: Leave this range hood with a close-fitting lid, cookie sheet or metal tray, then turn hood ON when cooking at high settings.
Always use only metal ductwork. 9. Use this manual.
2. Follow the heating equipment manufacturer's guideline and safety standards such as a tag...
KB-0333K Operation Manual / Installation Instructions - Page 5
... in cabinet or wall.
For vertical or horizontal discharge, run ductwork between service panel and hood location.
5 ROOF CAP
31/4" X 10" or 7" ROUND DUCT
(For vertical discharge)
SOFFIT
CABINET
HOOD 24" - 30" ABOVE COOKING SURFACE
HOUSE WIRING (Top or back of hood)
WALL CAP
31/4" X 10" DUCT (For horizontal discharge)
2 Use diagrams for proper...
KB-0333K Operation Manual / Installation Instructions - Page 6
... with one (1) screw. This will be heard when fully installed. with (5) #8 screws. Set filters aside.
3 Remove Teflon®Coated Bottom Cover from inside the hood. Set connector aside - DAMPER/ DUCT CONNECTOR
ELECTRICAL CABLE CLAMP
NON-DUCTED INSTALLATION - Skip to disconnect any wires.
8 Remove Baffle from top of hood.
6 held in place with mounting screws.
2 Remove tape...
KB-0333K Operation Manual / Installation Instructions - Page 7
... extreme off -center ductwork, the Damper/ Duct Connector can be installed up to 1⁄2" on either side of hood center or the 7" Round Duct Plate can be trimmed to trap wires between Support Fin and light panel.
11 Remove appropriate Duct Knockout(s) from range hood). DO NOT REMOVE the Metal Strip held in place with...
KB-0333K Operation Manual / Installation Instructions - Page 8
... upper and lower tabs.
5. Set aside for later. Slide the ...it is properly positioned as shown. Replace Retaining Ring from being switched on ...hood black wire, house white to the Stop Edge of electric shock, make sure power is switched off at the service panel. Make sure Tab on non-ducted filters, see page 9. Make sure wheel turns freely. PREPARE THE HOOD
Non-Ducted Installations...
KB-0333K Operation Manual / Installation Instructions - Page 9
... mesh filters. NON-DUCTED FILTERS
• Attach charcoal filters to be installed Non-Ducted:
• Purchase a set of (4) keyholes. INSTALL HOOD
4 Install (2) PAR20, 50 W Maximum Halogen Bulbs or (2) R16, 40 W Maximum Incandescent Bulbs. 1 Hang hood from Sharp (see page 2). Tighten mounting screws securely. Slide hood towards wall until mounting screws are facing down (toward the...
KB-0333K Operation Manual / Installation Instructions - Page 10
... shows the Sensor fan setting. Once the temperature has been reduced, the Sensor will change fan speed. Press the button again to turn
lights off . After replacing the cleaned filters (or installing new ones), press the "CLEAN FILTER" button to turn off the indicator light.
2
4
HEAT SENSOR
Your Sharp Insight Range Hood is not open (blown...
KB-0333K Operation Manual / Installation Instructions - Page 11
Use a damp cloth and a mild detergent to be replaced. Aluminum mesh filters: Clean frequently using hot water and a mild detergent...ALLOW WATER TO ENTER MOTOR. ducted installations): Clean filter surfaces frequently with a damp cloth and a mild detergent. The blue and yellow stripes will blend to change the filter. CLEANING
To clean hood: Remove filters. Charcoal filters (additional ...
Sharp KB-0333K Reviews
Do you have an experience with the Sharp KB-0333K that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Sharp yet.
Earn 750 points for your review!