Momentus 7200.2 SATA Product Manual
Page 3
...i commands 31 5.0 Seagate Technology support services 33 Momentus 7200.2 SATA Product Manual, Rev. Contents 1.0 Introduction 1 1.1 About the Serial ATA (SATA) interface 2 2.0 Drive specifications 3 2.1 Specification summary table 3 2.2 Formatted capacity 5 2.2.1 LBA mode 5 2.3 Default logical geometry 5 2.4 Physical organization 6 2.5 Recording and interface technology 6 2.6 Physical characteristics 6 2.7 Seek time 7 2.8 Start/stop times 7 2.9 Power specifications 8 2.9.1 Power consumption 8 2.9.2 Conducted noise 9 2.9.3 Voltage tolerance 9 2.9.4 Power-management modes 10...
...i commands 31 5.0 Seagate Technology support services 33 Momentus 7200.2 SATA Product Manual, Rev. Contents 1.0 Introduction 1 1.1 About the Serial ATA (SATA) interface 2 2.0 Drive specifications 3 2.1 Specification summary table 3 2.2 Formatted capacity 5 2.2.1 LBA mode 5 2.3 Default logical geometry 5 2.4 Physical organization 6 2.5 Recording and interface technology 6 2.6 Physical characteristics 6 2.7 Seek time 7 2.8 Start/stop times 7 2.9 Power specifications 8 2.9.1 Power consumption 8 2.9.2 Conducted noise 9 2.9.3 Voltage tolerance 9 2.9.4 Power-management modes 10...
Momentus 7200.2 SATA Product Manual
Page 7
... and interface specifications for the following Seagate Momentus® 7200.2 SATA model drives: • ST9200420ASG • ST9200420AS • ST9160823ASG • ST9160823AS • ST9120823AS • ST9100821AS • ST980813ASG • ST980813AS These drives provide the following key features: • 7,200 RPM spindle speed • 8 Mbyte buffer (80-160 GB models) • 16 Mbyte buffer (200 GB models) • Free Fall Protection (on ST9200420ASG, ST9160823ASG and ST980813ASG models only) • High instantaneous (burst) data-transfer rates...
... and interface specifications for the following Seagate Momentus® 7200.2 SATA model drives: • ST9200420ASG • ST9200420AS • ST9160823ASG • ST9160823AS • ST9120823AS • ST9100821AS • ST980813ASG • ST980813AS These drives provide the following key features: • 7,200 RPM spindle speed • 8 Mbyte buffer (80-160 GB models) • 16 Mbyte buffer (200 GB models) • Free Fall Protection (on ST9200420ASG, ST9160823ASG and ST980813ASG models only) • High instantaneous (burst) data-transfer rates...
Momentus 7200.2 SATA Product Manual
Page 8
... ATA device behavior to host software as normal. The Serial ATA host adapter and drive share the function of host bus addresses. It is no master/slave relationship with existing host systems and software. The specification can not operate at the same set any jumpers or other configuration options. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are represented to provide backward compatibility with Serial ATA devices like Device 0 devices...
... ATA device behavior to host software as normal. The Serial ATA host adapter and drive share the function of host bus addresses. It is no master/slave relationship with existing host systems and software. The specification can not operate at the same set any jumpers or other configuration options. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are represented to provide backward compatibility with Serial ATA devices like Device 0 devices...
Momentus 7200.2 SATA Product Manual
Page 9
... speed (RPM) Internal transfer rate (Mbits/sec max) Sustained transfer rate OD (Mbytes/sec) I/O data transfer rate (Gb/s max) ATA data-transfer modes supported Cache buffer (Mbytes) Height (max) Width (max) Length (max) Weight (typical) Average latency (msec) Power-on specification measurement or definition, see the appropriate section of this table are measured under ambient conditions, at 25°C, and nominal power. Table 1: Drive specifications Drive specification Formatted Gbytes (512 bytes/sector)* Guaranteed sectors Bytes per sector Default sectors per track Default read/write...
... speed (RPM) Internal transfer rate (Mbits/sec max) Sustained transfer rate OD (Mbytes/sec) I/O data transfer rate (Gb/s max) ATA data-transfer modes supported Cache buffer (Mbytes) Height (max) Width (max) Length (max) Weight (typical) Average latency (msec) Power-on specification measurement or definition, see the appropriate section of this table are measured under ambient conditions, at 25°C, and nominal power. Table 1: Drive specifications Drive specification Formatted Gbytes (512 bytes/sector)* Guaranteed sectors Bytes per sector Default sectors per track Default read/write...
Momentus 7200.2 SATA Product Manual
Page 10
...-to-track seek time (msec typical) 1.0 (read), 1.5 (write) Average seek, read Annualized Failure Rate (AFR) 0.73% Warranty 5 Years on the "Verify Your Warranty" link. D To determine the warranty for your drive. 4 Momentus 7200.2 SATA Product Manual, Rev. The system will be asked to provide the drive serial number, model number (or part number) and country of purchase. You will display the warranty information for a specific drive, use a web browser to peak, 5-500 Hz) Drive acoustics, sound power (bels) Idle** 2.5 (typical) 2.8 (max) Seek Nonrecoverable read errors...
...-to-track seek time (msec typical) 1.0 (read), 1.5 (write) Average seek, read Annualized Failure Rate (AFR) 0.73% Warranty 5 Years on the "Verify Your Warranty" link. D To determine the warranty for your drive. 4 Momentus 7200.2 SATA Product Manual, Rev. The system will be asked to provide the drive serial number, model number (or part number) and country of purchase. You will display the warranty information for a specific drive, use a web browser to peak, 5-500 Hz) Drive acoustics, sound power (bels) Idle** 2.5 (typical) 2.8 (max) Seek Nonrecoverable read errors...
Momentus 7200.2 SATA Product Manual
Page 11
... additional information about 48bit addressing support of drives with capacities over 137 Gbytes. 2.3 Default logical geometry Cylinders 16,383 Read/write heads 16 Sectors per track 63 LBA mode When addressing these drives in the S3 and S4 states, drive sleep and drive standby modes will pull power to the drive when entering S3 and S4; Accessible capacity may increase acoustic and power to operational levels. ***Typical notebooks will not contribute to battery power consumption. 2.2 Formatted capacity Model ST9200420AS and...
... additional information about 48bit addressing support of drives with capacities over 137 Gbytes. 2.3 Default logical geometry Cylinders 16,383 Read/write heads 16 Sectors per track 63 LBA mode When addressing these drives in the S3 and S4 states, drive sleep and drive standby modes will pull power to the drive when entering S3 and S4; Accessible capacity may increase acoustic and power to operational levels. ***Typical notebooks will not contribute to battery power consumption. 2.2 Formatted capacity Model ST9200420AS and...
Momentus 7200.2 SATA Product Manual
Page 12
... ST9160823AS and ST9160823ASG ST9120823AS ST9100821AS ST980813AS and ST980813ASG Read/write heads 4 3 2 Number of discs 2 1 2.5 Recording and interface technology Interface Recording density BPI (bits/inch max) Track density TPI (tracks/inch max) Areal density (Gbits/inch2 max) Spindle speed (RPM) (± 0.2%) Maximum Internal transfer rate (Mbits/sec) Sustained transfer rate OD (Mbytes/sec max) I/O data-transfer rate (Mbytes/sec max) Interleave Cache buffer 200 GB models 160 - 80 GB models Serial ATA (SATA) 1,014,000 853,000 162,600 155,000...
... ST9160823AS and ST9160823ASG ST9120823AS ST9100821AS ST980813AS and ST980813ASG Read/write heads 4 3 2 Number of discs 2 1 2.5 Recording and interface technology Interface Recording density BPI (bits/inch max) Track density TPI (tracks/inch max) Areal density (Gbits/inch2 max) Spindle speed (RPM) (± 0.2%) Maximum Internal transfer rate (Mbits/sec) Sustained transfer rate OD (Mbytes/sec max) I/O data-transfer rate (Mbytes/sec max) Interleave Cache buffer 200 GB models 160 - 80 GB models Serial ATA (SATA) 1,014,000 853,000 162,600 155,000...
Momentus 7200.2 SATA Product Manual
Page 16
... Momentus 7200.2 SATA Product Manual, Rev. The drive accepts all commands and returns to Active mode any time disc access is reinitialized and begins counting down from its specified delay times to Active mode any time disc access is at rest. After receiving a reset, the drive exits Sleep mode and enters Standby mode with all current translation parameters intact. • Idle and Standby timers Each time the drive performs an Active function (read /write and seek operations...
... Momentus 7200.2 SATA Product Manual, Rev. The drive accepts all commands and returns to Active mode any time disc access is reinitialized and begins counting down from its specified delay times to Active mode any time disc access is at rest. After receiving a reset, the drive exits Sleep mode and enters Standby mode with all current translation parameters intact. • Idle and Standby timers Each time the drive performs an Active function (read /write and seek operations...
Momentus 7200.2 SATA Product Manual
Page 19
... acoustic and power to operational levels. 2.12 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in seek mode only. The number of seeks per second is defined by the following table: Table 6: Radio frequency environments Test Electrostatic discharge Radiated RF immunity Electrical fast transient Surge immunity Conducted RF immunity Voltage dips, interrupts Description Performance level...
... acoustic and power to operational levels. 2.12 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in seek mode only. The number of seeks per second is defined by the following table: Table 6: Radio frequency environments Test Electrostatic discharge Radiated RF immunity Electrical fast transient Surge immunity Conducted RF immunity Voltage dips, interrupts Description Performance level...
Momentus 7200.2 SATA Product Manual
Page 20
... and ST980813ASG models, use Set Features command C1h. The drive is operating. 2.13 Reliability Measurement type Nonrecoverable read errors Annualized Failure Rate (AFR) Load/Unload (U/UL) 25°C, 50% relative humidity 32°C, 80% relative humidity 5°C, 80% relative humidity 5°C, 20% relative humidity 60°C, 20% relative humidity Warranty Specification 1 per 1014 bits read, max. 0.73% 600,000 software-controlled power on/off cycles 20,000 hard power on...
... and ST980813ASG models, use Set Features command C1h. The drive is operating. 2.13 Reliability Measurement type Nonrecoverable read errors Annualized Failure Rate (AFR) Load/Unload (U/UL) 25°C, 50% relative humidity 32°C, 80% relative humidity 5°C, 80% relative humidity 5°C, 20% relative humidity 60°C, 20% relative humidity Warranty Specification 1 per 1014 bits read, max. 0.73% 600,000 software-controlled power on/off cycles 20,000 hard power on...
Momentus 7200.2 SATA Product Manual
Page 21
... Superintendent of Documents, U.S. Momentus 7200.2 SATA Product Manual, Rev. As a subassembly, no guarantee that the total assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for additional suggestions. Government Printing Office, Washington, DC 20402. Korean RRL If these models have the C-Tick marking, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet...
... Superintendent of Documents, U.S. Momentus 7200.2 SATA Product Manual, Rev. As a subassembly, no guarantee that the total assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for additional suggestions. Government Printing Office, Washington, DC 20402. Korean RRL If these models have the C-Tick marking, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet...
Momentus 7200.2 SATA Product Manual
Page 26
... adapter. Serial ATA drives are inserted directly into the host receptacle. Attaching SATA cabling Each cable is normally not necessary to ensure correct orientation. 20 Momentus 7200.2 SATA Product Manual, Rev. Signal connector Power connector Signal cable Power cable Figure 3. There is no master/slave relationship because each drive is considered a master in two differential pairs, plus three ground connections. 3.2 Configuring the drive Each drive on this drive for proper operation. It is keyed to set any jumpers on the Serial ATA interface connects...
... adapter. Serial ATA drives are inserted directly into the host receptacle. Attaching SATA cabling Each cable is normally not necessary to ensure correct orientation. 20 Momentus 7200.2 SATA Product Manual, Rev. Signal connector Power connector Signal cable Power cable Figure 3. There is no master/slave relationship because each drive is considered a master in two differential pairs, plus three ground connections. 3.2 Configuring the drive Each drive on this drive for proper operation. It is keyed to set any jumpers on the Serial ATA interface connects...
Momentus 7200.2 SATA Product Manual
Page 31
...00H Password: 01H Lock: 02H Unlock: 03H Freeze Lock: 04H Momentus 7200.2 SATA Product Manual, Rev. D 25 implementation. 4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. Command name ATA-standard commands Device Configuration Restore Device Configuration Freeze Lock Device Configuration Identify Device Configuration Set Download Microcode Execute Device Diagnostics Flush Cache Flush Cache Extended Identify Device Initialize Device Parameters Read Buffer Read DMA Read DMA Extended Read DMA without Retries Read Long...
...00H Password: 01H Lock: 02H Unlock: 03H Freeze Lock: 04H Momentus 7200.2 SATA Product Manual, Rev. D 25 implementation. 4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. Command name ATA-standard commands Device Configuration Restore Device Configuration Freeze Lock Device Configuration Identify Device Configuration Set Download Microcode Execute Device Diagnostics Flush Cache Flush Cache Extended Identify Device Initialize Device Parameters Read Buffer Read DMA Read DMA Extended Read DMA without Retries Read Long...
Momentus 7200.2 SATA Product Manual
Page 33
... 3 for default parameter settings. abled 50 ATA-reserved Value 0C5AH 16,383 0000H 16 0000H 0000H 003FH 0000H ASCII 0000H 0400H 0000H x.xx ST9200420ASG ST9200420AS ST9160823ASG ST9160823AS ST9120823AS ST9100821AS ST980813ASG ST980813AS 8010H 0000H 2F00H 0000H Momentus 7200.2 SATA Product Manual, Rev. Command name Security Erase Unit Security Freeze Lock Security Disable Password Command code (in hex) F4h F5h F6h 4.3.1 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following commands contain drive-specific...
... 3 for default parameter settings. abled 50 ATA-reserved Value 0C5AH 16,383 0000H 16 0000H 0000H 003FH 0000H ASCII 0000H 0400H 0000H x.xx ST9200420ASG ST9200420AS ST9160823ASG ST9160823AS ST9120823AS ST9100821AS ST980813ASG ST980813AS 8010H 0000H 2F00H 0000H Momentus 7200.2 SATA Product Manual, Rev. Command name Security Erase Unit Security Freeze Lock Security Disable Password Command code (in hex) F4h F5h F6h 4.3.1 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following commands contain drive-specific...
Momentus 7200.2 SATA Product Manual
Page 34
...data-transfer cycle timing mode Retired Words 54-58, 64-70 and 88 are valid Number of current logical cylinders Number of current logical heads Number of current logical sectors per logical track Current capacity in sectors Number of sectors transferred during a Read Multiple or Write Multiple command Total number of user-addressable LBA sectors available (see Section 2.2 for related information) Retired Multiword DMA active and modes supported (see note following this table) Advanced PIO modes supported (modes... 30xxH 0001H 4000H xx3FH 0000H 28 Momentus 7200.2 SATA Product Manual, Rev. D
...data-transfer cycle timing mode Retired Words 54-58, 64-70 and 88 are valid Number of current logical cylinders Number of current logical heads Number of current logical sectors per logical track Current capacity in sectors Number of sectors transferred during a Read Multiple or Write Multiple command Total number of user-addressable LBA sectors available (see Section 2.2 for related information) Retired Multiword DMA active and modes supported (see note following this table) Advanced PIO modes supported (modes... 30xxH 0001H 4000H xx3FH 0000H 28 Momentus 7200.2 SATA Product Manual, Rev. D
Momentus 7200.2 SATA Product Manual
Page 35
... DMA mode 2 is supported. 3 Ultra DMA mode 3 is disabled 0000H 0001H xxxxH 0000H xxA5H Note. Momentus 7200.2 SATA Product Manual, Rev. Word 90 92 93 94 95-99 100- 103 104- 118 119 120 121- 127 128 129- 159 160- 254 255 Description Enhanced security erase time Master password revision code Hardware reset value (see description following this table) Auto acoustic management setting ATA-reserved Total number of user-addressable LBA sectors...
... DMA mode 2 is supported. 3 Ultra DMA mode 3 is disabled 0000H 0001H xxxxH 0000H xxA5H Note. Momentus 7200.2 SATA Product Manual, Rev. Word 90 92 93 94 95-99 100- 103 104- 118 119 120 121- 127 128 129- 159 160- 254 255 Description Enhanced security erase time Master password revision code Hardware reset value (see description following this table) Auto acoustic management setting ATA-reserved Total number of user-addressable LBA sectors...
Momentus 7200.2 SATA Product Manual
Page 37
... software reset, the default values of the features are predictable. command for disc drives. commands Code in drive self-test (DST S.M.A.R.T. Read Data Vendor-specific S.M.A.R.T. Execute Off-line Immediate (runs DST) S.M.A.R.T. Table 8: Set Features command values C1H Disable the Free Fall Protection feature (41H above . 4.3.3 S.M.A.R.T. is written to the Error register. This drive is shipped with all failures are as indicated above enables the Free Fall Protection feature) F1H Report full capacity...
... software reset, the default values of the features are predictable. command for disc drives. commands Code in drive self-test (DST S.M.A.R.T. Read Data Vendor-specific S.M.A.R.T. Execute Off-line Immediate (runs DST) S.M.A.R.T. Table 8: Set Features command values C1H Disable the Free Fall Protection feature (41H above . 4.3.3 S.M.A.R.T. is written to the Error register. This drive is shipped with all failures are as indicated above enables the Free Fall Protection feature) F1H Report full capacity...
Momentus 7200.2 SATA Product Manual
Page 40
..." page on www.seagate.com. 34 Momentus 7200.2 SATA Product Manual, Rev. Asia/Pacific Support Services For an extensive list of telephone numbers to technical support, presales and warranty service in USA/ Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com. Resellers or end users of drive products should contact their place of telephone numbers to technical support, presales and warranty service in Europe, the...
..." page on www.seagate.com. 34 Momentus 7200.2 SATA Product Manual, Rev. Asia/Pacific Support Services For an extensive list of telephone numbers to technical support, presales and warranty service in USA/ Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com. Resellers or end users of drive products should contact their place of telephone numbers to technical support, presales and warranty service in Europe, the...
Momentus 7200.2 SATA Product Manual
Page 42
... Initialize Device Parameters 25 Input noise ripple 9 Interface 6 interface 23 Interleave 6 Internal data transfer rate 3 Internal data-transfer rate 6 is 7 ISO document 7779 13 ITE 14 K Korean RRL 15 L latency 3 LBA mode 5 Length 3 length 6 Load/Unload 14 logical geometry 5 M master/slave 2 Max Address 25 maximum temperature 11 Microcode 25 mounting 21 mounting screws 12 36 mounting the drive 19 N noise 9 nominal power 7 Nonoperating shock 12 Nonoperating vibration 12 Nonrecoverable read errors 4 nonrecoverable read errors 14 O Operating power 4 Operating...
... Initialize Device Parameters 25 Input noise ripple 9 Interface 6 interface 23 Interleave 6 Internal data transfer rate 3 Internal data-transfer rate 6 is 7 ISO document 7779 13 ITE 14 K Korean RRL 15 L latency 3 LBA mode 5 Length 3 length 6 Load/Unload 14 logical geometry 5 M master/slave 2 Max Address 25 maximum temperature 11 Microcode 25 mounting 21 mounting screws 12 36 mounting the drive 19 N noise 9 nominal power 7 Nonoperating shock 12 Nonoperating vibration 12 Nonrecoverable read errors 4 nonrecoverable read errors 14 O Operating power 4 Operating...
Momentus 7200.2 SATA Product Manual
Page 43
... 12, 21 sector 5 sectors 5 Sectors per track 5 sectors per track 3 Security Disable Password 27 Security Erase Prepare 26 Security Erase Unit 27 Security Freeze Lock 27 Security Set Password 26 Security Unlock 26 Seek 25 seek mode 8 Seek power 4 Seek time 7 seek time 4 Seeking 8 Serial ATA 6 Serial ATA (SATA) interface 23 serial ATA ports 2 servo electronics 8 Set Features 25 Set Max Address 25 Set Multiple Mode 26 Shock 12 Shock, nonoperating 4 Shock, operating 4 single-track seeks 7 Sleep 8, 26 Sleep mode 4, 10 sound power 4 Specification summary table 3 Spindle speed 3, 6 Spinup 8 spinup...
... 12, 21 sector 5 sectors 5 Sectors per track 5 sectors per track 3 Security Disable Password 27 Security Erase Prepare 26 Security Erase Unit 27 Security Freeze Lock 27 Security Set Password 26 Security Unlock 26 Seek 25 seek mode 8 Seek power 4 Seek time 7 seek time 4 Seeking 8 Serial ATA 6 Serial ATA (SATA) interface 23 serial ATA ports 2 servo electronics 8 Set Features 25 Set Max Address 25 Set Multiple Mode 26 Shock 12 Shock, nonoperating 4 Shock, operating 4 single-track seeks 7 Sleep 8, 26 Sleep mode 4, 10 sound power 4 Specification summary table 3 Spindle speed 3, 6 Spinup 8 spinup...