Product Manual
Page 6
D 2.0 Configuring and mounting the drive 17 2.1 Handling and static-discharge precautions 17 2.2 Jumper settings 18 2.2.1 Master/slave configuration 18 2.2.2 Cable-select option 19 2.3 Ultra ATA/66 cable 19 2.4 Drive mounting 19 3.0 ATA interface 21 3.1 ATA interface signals and connector pins 21 3.2 ATA Interface commands 23 3.2.1 Supported ATA commands 23 3.2.2 Identify Drive command 24 3.2.3 Set Features command 29 3.2.4 S.M.A.R.T. commands 30 iv U4 Family Product Manual, Rev.
D 2.0 Configuring and mounting the drive 17 2.1 Handling and static-discharge precautions 17 2.2 Jumper settings 18 2.2.1 Master/slave configuration 18 2.2.2 Cable-select option 19 2.3 Ultra ATA/66 cable 19 2.4 Drive mounting 19 3.0 ATA interface 21 3.1 ATA interface signals and connector pins 21 3.2 ATA Interface commands 23 3.2.1 Supported ATA commands 23 3.2.2 Identify Drive command 24 3.2.3 Set Features command 29 3.2.4 S.M.A.R.T. commands 30 iv U4 Family Product Manual, Rev.
Product Manual
Page 7
Mounting dimensions-top, side and end view 20 Figure 4. U4 Family Product Manual, Rev. Typical startup and operation current profile 9 Figure 2. I/O pins and supported ATA signals 22 D v Figures Figure 1. Master/slave jumper settings 18 Figure 3.
Mounting dimensions-top, side and end view 20 Figure 4. U4 Family Product Manual, Rev. Typical startup and operation current profile 9 Figure 2. I/O pins and supported ATA signals 22 D v Figures Figure 1. Master/slave jumper settings 18 Figure 3.
Product Manual
Page 26
... the factory for operation. It is master with a jumper set on pins 7 and 8. The drive is used to configure the drive as a master or a slave. Master/slave jumper settings Use this jumper setting only if the drive does not work as a master with a non-ATA-compatible slave. 18 U4 Family Product Manual, Rev. Set a jumper on pins 5 and 6 and a jumper on pins 7 and 8.
... the factory for operation. It is master with a jumper set on pins 7 and 8. The drive is used to configure the drive as a master or a slave. Master/slave jumper settings Use this jumper setting only if the drive does not work as a master with a non-ATA-compatible slave. 18 U4 Family Product Manual, Rev. Set a jumper on pins 5 and 6 and a jumper on pins 7 and 8.
Product Manual
Page 27
...pin 34, CBLID-, on the interface bus. The result is reported in a Fast Rise Detected bit (bit 13 of the drive for drive mounting dimensions. To enable cable select, set a jumper on the interface bus. Consult your computer manual to determine whether your computer supports this option. 2.3 Ultra ATA/66 cable ... You can mount the drive in any orientation using four screws in the sidemounting holes or four screws in Figure 2 on the cable. U4 Family Product Manual, Rev. This cable uses even-numbered conductors connected to the ground pins to run Ultra DMA mode 3 and 4. See Figure 4 ...
...pin 34, CBLID-, on the interface bus. The result is reported in a Fast Rise Detected bit (bit 13 of the drive for drive mounting dimensions. To enable cable select, set a jumper on the interface bus. Consult your computer manual to determine whether your computer supports this option. 2.3 Ultra ATA/66 cable ... You can mount the drive in any orientation using four screws in the sidemounting holes or four screws in Figure 2 on the cable. U4 Family Product Manual, Rev. This cable uses even-numbered conductors connected to the ground pins to run Ultra DMA mode 3 and 4. See Figure 4 ...