Product Manual
Page 6
commands 30 iv U4 Family Product Manual, Rev. D 2.0 Configuring and mounting the drive 17 2.1 Handling and static-discharge precautions 17 2.2 Jumper settings 18 2.2.1 Master/slave configuration 18 2.2.2 Cable-select option 19 2.3 Ultra ATA/66 cable 19 2.4 Drive mounting 19 3.0 ATA interface 21 3.1 ATA interface signals and connector pins 21 3.2 ATA Interface commands 23 3.2.1 Supported ATA commands 23 3.2.2 Identify Drive command 24 3.2.3 Set Features command 29 3.2.4 S.M.A.R.T.
commands 30 iv U4 Family Product Manual, Rev. D 2.0 Configuring and mounting the drive 17 2.1 Handling and static-discharge precautions 17 2.2 Jumper settings 18 2.2.1 Master/slave configuration 18 2.2.2 Cable-select option 19 2.3 Ultra ATA/66 cable 19 2.4 Drive mounting 19 3.0 ATA interface 21 3.1 ATA interface signals and connector pins 21 3.2 ATA Interface commands 23 3.2.1 Supported ATA commands 23 3.2.2 Identify Drive command 24 3.2.3 Set Features command 29 3.2.4 S.M.A.R.T.
Product Manual
Page 7
D v Figures Figure 1. Master/slave jumper settings 18 Figure 3. I/O pins and supported ATA signals 22 Mounting dimensions-top, side and end view 20 Figure 4. Typical startup and operation current profile 9 Figure 2. U4 Family Product Manual, Rev.
D v Figures Figure 1. Master/slave jumper settings 18 Figure 3. I/O pins and supported ATA signals 22 Mounting dimensions-top, side and end view 20 Figure 4. Typical startup and operation current profile 9 Figure 2. U4 Family Product Manual, Rev.
Product Manual
Page 26
...-compatible slave. Set a jumper on pins 5 and 6 and a jumper on pins 7 and 8. Options jumper block (J8) Master or single drive Drive is slave. Master/slave jumper settings 18 U4 Family Product Manual, Rev. Master or single drive. Drive is the 6-pin dual header between the I/O connector and the power connector. Use this jumper setting only if the drive does not work...
...-compatible slave. Set a jumper on pins 5 and 6 and a jumper on pins 7 and 8. Options jumper block (J8) Master or single drive Drive is slave. Master/slave jumper settings 18 U4 Family Product Manual, Rev. Master or single drive. Drive is the 6-pin dual header between the I/O connector and the power connector. Use this jumper setting only if the drive does not work...
Product Manual
Page 27
...: 6 inch-lb). • Do not use cable-select determine the master and slave drives by their physical position on the interface bus. To enable cable select, set a jumper on page 18. The drive detects the 80-conductor cable by sampling pin 34, CBLID-, on the cable. signal. ... 80-conductor 40-pin cable is reported in a Fast Rise Detected bit (bit 13 of the drive for drive mounting dimensions. The result is required to run Ultra DMA mode 3 and 4. U4 Family Product Manual, Rev. Consult your computer manual to improve signal integrity. Important mounting precautions: •...
...: 6 inch-lb). • Do not use cable-select determine the master and slave drives by their physical position on the interface bus. To enable cable select, set a jumper on page 18. The drive detects the 80-conductor cable by sampling pin 34, CBLID-, on the cable. signal. ... 80-conductor 40-pin cable is reported in a Fast Rise Detected bit (bit 13 of the drive for drive mounting dimensions. The result is required to run Ultra DMA mode 3 and 4. U4 Family Product Manual, Rev. Consult your computer manual to improve signal integrity. Important mounting precautions: •...