SV35.4 Series SATA Product Manual
Page 7
... SV35.4 Series SATA Product Manual, Rev. 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate SV35.4TM Series model drive: ST3320410SV These drives provide the following key features: • High instantaneous (burst) data-transfer rates... and on-the-fly error-correction algorithms. • Native Command Queueing with command ordering to increase performance in demanding applications. • Full-track multiple-sector transfer capability without local processor intervention. • Quiet operation. •...
... SV35.4 Series SATA Product Manual, Rev. 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate SV35.4TM Series model drive: ST3320410SV These drives provide the following key features: • High instantaneous (burst) data-transfer rates... and on-the-fly error-correction algorithms. • Native Command Queueing with command ordering to increase performance in demanding applications. • Full-track multiple-sector transfer capability without local processor intervention. • Quiet operation. •...
SV35.4 Series SATA Product Manual
Page 8
... Serial ATA environment. Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in a point-to higher performance levels. 1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. A host adapter that shadow the contents...
... Serial ATA environment. Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in a point-to higher performance levels. 1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. A host adapter that shadow the contents...
SV35.4 Series SATA Product Manual
Page 13
2.5 Physical characteristics Maximum height Maximum width Maximum length Typical weight Cache buffer 320GB model 20.20 mm (0.794 inches) 101.85 mm (4.010 inches) 146.99 mm (5.787 inches) 380 grams (0.838 lb.) 16 Mbytes (16,384 kbytes) 2.6 Seek time Seek measurements are taken with nominal power at least 5,000 measurements of at 25°C ambient temperature. Typical seek times (msec) Track-to -track seek time is an average of all possible single-track seeks in both directions. • Average seek time is a true statistical random average of seeks between random tracks, less ...
2.5 Physical characteristics Maximum height Maximum width Maximum length Typical weight Cache buffer 320GB model 20.20 mm (0.794 inches) 101.85 mm (4.010 inches) 146.99 mm (5.787 inches) 380 grams (0.838 lb.) 16 Mbytes (16,384 kbytes) 2.6 Seek time Seek measurements are taken with nominal power at least 5,000 measurements of at 25°C ambient temperature. Typical seek times (msec) Track-to -track seek time is an average of all possible single-track seeks in both directions. • Average seek time is a true statistical random average of seeks between random tracks, less ...
SV35.4 Series SATA Product Manual
Page 16
.... • Idle mode The buffer remains enabled, and the drive accepts all current translation parameters intact. • Idle and Standby timers Each time the drive performs an Active function (read, write or seek), the standby timer is necessary. • Standby mode The drive enters Standby mode when the host sends a Standby...
.... • Idle mode The buffer remains enabled, and the drive accepts all current translation parameters intact. • Idle and Standby timers Each time the drive performs an Active function (read, write or seek), the standby timer is necessary. • Standby mode The drive enters Standby mode when the host sends a Standby...
SV35.4 Series SATA Product Manual
Page 18
...displacement) 0.50 Gs 0.25 Gs 2.9.6.2 Nonoperating vibration The maximum nonoperating vibration levels that the drive may experience while meeting the performance standards specified in this document when subjected to a maximum operating shock of 70 Gs based on a nonrepetitive half-sine shock pulse...or Z axis. 2.9.6.1 Operating vibration The maximum vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation is 350 Gs based on half-sine shock pulses of 2 msec duration. 2.9.6 Vibration All ...
...displacement) 0.50 Gs 0.25 Gs 2.9.6.2 Nonoperating vibration The maximum nonoperating vibration levels that the drive may experience while meeting the performance standards specified in this document when subjected to a maximum operating shock of 70 Gs based on a nonrepetitive half-sine shock pulse...or Z axis. 2.9.6.1 Operating vibration The maximum vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation is 350 Gs based on half-sine shock pulses of 2 msec duration. 2.9.6 Vibration All ...
SV35.4 Series SATA Product Manual
Page 19
.... 2.11 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table: Table 4: Radio frequency environments Test ... occur according to Annex D of hearing. Test for Prominent Discrete Tones (PDTs) Seagate follows the ECMA-74 standards for the inaudible components of sound prior to computation of tone ratios according to the S.M.A.R.T. Air: ± 8 kV Performance level B 80 to 1,000 MHz, 3 V/m, A 80% AM with 1...
.... 2.11 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table: Table 4: Radio frequency environments Test ... occur according to Annex D of hearing. Test for Prominent Discrete Tones (PDTs) Seagate follows the ECMA-74 standards for the inaudible components of sound prior to computation of tone ratios according to the S.M.A.R.T. Air: ± 8 kV Performance level B 80 to 1,000 MHz, 3 V/m, A 80% AM with 1...
SV35.4 Series SATA Product Manual
Page 20
...consumer electronics environment of power-on all applicable sections of IEC950 and EN 60950. 2.13.2 Electromagnetic compatibility Hard drives that is performed to access the following assumptions for operation inside a properly designed enclosure, with the directives. The system will comply with properly... Drives are defined by EN 55022, Class B and the immunity levels are tested in representative end-user systems. Although CE-marked Seagate drives comply with 60 cycles per year. • Operations at excessive I /O duty cycle affect the product AFR. 2.12 Reliability...
...consumer electronics environment of power-on all applicable sections of IEC950 and EN 60950. 2.13.2 Electromagnetic compatibility Hard drives that is performed to access the following assumptions for operation inside a properly designed enclosure, with the directives. The system will comply with properly... Drives are defined by EN 55022, Class B and the immunity levels are tested in representative end-user systems. Although CE-marked Seagate drives comply with 60 cycles per year. • Operations at excessive I /O duty cycle affect the product AFR. 2.12 Reliability...
SV35.5 Series SATA Product Manual
Page 7
...Series SATA Product Manual, Rev. 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate SV35.5TM Series model drive: ST31000525SV ST3500410SV ST3250311SV These drives provide the following key features: • Designed with ...art cache and on-the-fly error-correction algorithms. • Native Command Queueing with command ordering to increase performance in demanding applications. • Full-track multiple-sector transfer capability without local processor intervention. • Quiet operation. • SeaTools...
...Series SATA Product Manual, Rev. 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate SV35.5TM Series model drive: ST31000525SV ST3500410SV ST3250311SV These drives provide the following key features: • Designed with ...art cache and on-the-fly error-correction algorithms. • Native Command Queueing with command ordering to increase performance in demanding applications. • Full-track multiple-sector transfer capability without local processor intervention. • Quiet operation. • SeaTools...
SV35.5 Series SATA Product Manual
Page 8
... drives are Device 0 (master) devices. All Serial ATA devices behave like there is not necessary to set of emulating parallel ATA device behavior to higher performance levels. A Serial ATA was designed to allow you to host software where two devices on two separate ports. The host adapter may, optionally, emulate a master...
... drives are Device 0 (master) devices. All Serial ATA devices behave like there is not necessary to set of emulating parallel ATA device behavior to higher performance levels. A Serial ATA was designed to allow you to host software where two devices on two separate ports. The host adapter may, optionally, emulate a master...
SV35.5 Series SATA Product Manual
Page 17
... Immediate command. In both Idle and Standby mode, the drive accepts all current translation parameters intact. • Idle and Standby timers Each time the drive performs an Active function (read /write and seek operations. • Idle mode The buffer remains enabled, and the drive accepts all commands and returns to Standby...
... Immediate command. In both Idle and Standby mode, the drive accepts all current translation parameters intact. • Idle and Standby timers Each time the drive performs an Active function (read /write and seek operations. • Idle mode The buffer remains enabled, and the drive accepts all commands and returns to Standby...
SV35.5 Series SATA Product Manual
Page 19
...assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Vibration may experience while meeting the performance standards specified in this document are specified below 5-22 Hz 22-350 Hz 350-500 Hz 0.25 Gs (Limited displacement) 0.50 ...per second. 2.9.5.2 Nonoperating shock 2 disk models The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration. 1 disk models The...
...assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Vibration may experience while meeting the performance standards specified in this document are specified below 5-22 Hz 22-350 Hz 350-500 Hz 0.25 Gs (Limited displacement) 0.50 ...per second. 2.9.5.2 Nonoperating shock 2 disk models The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration. 1 disk models The...
SV35.5 Series SATA Product Manual
Page 20
...(typ) 2.8 bels (max) [1] During periods of drive idle, some offline activity may increase acoustic and power to the radio frequency (RF) environments defined in performance when subjected to operational levels. An exception to the S.M.A.R.T. Testing is measured consistent with 1 kHz sine A 0% open, 5 seconds C 0% short, 5 seconds...25 degrees C). specification, which may occur according to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the inaudible components of...
...(typ) 2.8 bels (max) [1] During periods of drive idle, some offline activity may increase acoustic and power to the radio frequency (RF) environments defined in performance when subjected to operational levels. An exception to the S.M.A.R.T. Testing is measured consistent with 1 kHz sine A 0% open, 5 seconds C 0% short, 5 seconds...25 degrees C). specification, which may occur according to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the inaudible components of...
SV35.5 Series SATA Product Manual
Page 21
... the specifications in the test systems, we cannot guarantee that are tested in representative end-user systems. Although CE-marked Seagate drives comply with 60 cycles per year. • Operations at temperatures outside the specifications in the Electromagnetic Compatibility Directive (...should confirm EMC compliance and provide CE marking for operation inside a properly designed enclosure, with the directives. The drive is performed to individual units. You will display the warranty information for desktop personal computers. SV35.5 Series SATA Product Manual, Rev....
... the specifications in the test systems, we cannot guarantee that are tested in representative end-user systems. Although CE-marked Seagate drives comply with 60 cycles per year. • Operations at temperatures outside the specifications in the Electromagnetic Compatibility Directive (...should confirm EMC compliance and provide CE marking for operation inside a properly designed enclosure, with the directives. The drive is performed to individual units. You will display the warranty information for desktop personal computers. SV35.5 Series SATA Product Manual, Rev....
SV35.3 Series SATA Product Manual
Page 7
...Series Serial ATA Product Manual, Rev. 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate SV35.3 Series® Serial ATA model drives: ST31000340SV ST3750330SV ST3500320SV ST3250310SV These drives provide the following key features: •...and on-the-fly error-correction algorithms. • Native Command Queueing with command ordering to increase performance in demanding applications. • Full-track multiple-sector transfer capability without local processor intervention. • Quiet operation. •...
...Series Serial ATA Product Manual, Rev. 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate SV35.3 Series® Serial ATA model drives: ST31000340SV ST3750330SV ST3500320SV ST3250310SV These drives provide the following key features: •...and on-the-fly error-correction algorithms. • Native Command Queueing with command ordering to increase performance in demanding applications. • Full-track multiple-sector transfer capability without local processor intervention. • Quiet operation. •...
SV35.3 Series SATA Product Manual
Page 8
... interface. In addition, Serial ATA makes the transition from www.serialata.org. 2 SV35.3 Series Serial ATA Product Manual, Rev. This is not necessary to higher performance levels. All Serial ATA devices behave like there is no master/slave relationship with Serial ATA devices like Device 0 devices. The specification can be downloaded...
... interface. In addition, Serial ATA makes the transition from www.serialata.org. 2 SV35.3 Series Serial ATA Product Manual, Rev. This is not necessary to higher performance levels. All Serial ATA devices behave like there is no master/slave relationship with Serial ATA devices like Device 0 devices. The specification can be downloaded...
SV35.3 Series SATA Product Manual
Page 20
.... • Idle mode The buffer remains enabled, and the drive accepts all current translation parameters intact. • Idle and Standby timers Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting down from its specified delay times to Active mode any...
.... • Idle mode The buffer remains enabled, and the drive accepts all current translation parameters intact. • Idle and Standby timers Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting down from its specified delay times to Active mode any...
SV35.3 Series SATA Product Manual
Page 22
...25 Gs 2.9.6.2 Nonoperating vibration The maximum nonoperating vibration levels that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration. 2.9.6 ... second. 2.9.5.2 Nonoperating shock (4, 3 and 2 disc models) The nonoperating shock level that the drive may experience while meeting the performance standards specified in this document when subjected to a maximum operating shock of 63 Gs based on a nonrepetitive half-sine shock pulse ...
...25 Gs 2.9.6.2 Nonoperating vibration The maximum nonoperating vibration levels that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration. 2.9.6 ... second. 2.9.5.2 Nonoperating shock (4, 3 and 2 disc models) The nonoperating shock level that the drive may experience while meeting the performance standards specified in this document when subjected to a maximum operating shock of 63 Gs based on a nonrepetitive half-sine shock pulse ...
SV35.3 Series SATA Product Manual
Page 23
...levels (no pure tones). For seek mode tests, the drive is defined by the following table: Table 5: Radio frequency environments Test Description Performance level Reference standard Electrostatic Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV B discharge EN 61000-4-2: 95 Radiated ...power to operational levels. 2.11 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to 80 MHz, 3 Vrms, 80% AM with 1 kHz sine A immunity EN 61000-4-6: 97 Voltage dips, interrupts 0%...
...levels (no pure tones). For seek mode tests, the drive is defined by the following table: Table 5: Radio frequency environments Test Description Performance level Reference standard Electrostatic Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV B discharge EN 61000-4-2: 95 Radiated ...power to operational levels. 2.11 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to 80 MHz, 3 Vrms, 80% AM with 1 kHz sine A immunity EN 61000-4-6: 97 Voltage dips, interrupts 0%...
SV35.3 Series SATA Product Manual
Page 25
... of the Australian Communication Authority (ACA). 2.13.3 FCC verification These drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in strict accordance with UL 1950 and CSA C22.2 (950) and meet the Electromagnetic Compatibility...comply with the Australia/New Zealand Standard AS/NZS3548 1995 and meet all systems will not occur in a residential installation. Testing is performed to radio or television, which can be a subassembly even when it is likely to result in enclosures as an external device). Computer...
... of the Australian Communication Authority (ACA). 2.13.3 FCC verification These drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in strict accordance with UL 1950 and CSA C22.2 (950) and meet the Electromagnetic Compatibility...comply with the Australia/New Zealand Standard AS/NZS3548 1995 and meet all systems will not occur in a residential installation. Testing is performed to radio or television, which can be a subassembly even when it is likely to result in enclosures as an external device). Computer...
SV35.2 Series PATA Product Manual
Page 7
...Product Manual, Rev. E 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate® SV35.2 Series® PATA model drives: ST3750640AV ST3500630AV ST3320620AV ST3250820AV ST3160815AV These drives provide the following key features... • Full-track multiple-sector transfer capability without local processor intervention. • Quiet operation. • SeaTools diagnostic software performs a drive self-test that use cable select (CSEL). drive monitoring and reporting. • Support for Read Multiple and Write Multiple ...
...Product Manual, Rev. E 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate® SV35.2 Series® PATA model drives: ST3750640AV ST3500630AV ST3320620AV ST3250820AV ST3160815AV These drives provide the following key features... • Full-track multiple-sector transfer capability without local processor intervention. • Quiet operation. • SeaTools diagnostic software performs a drive self-test that use cable select (CSEL). drive monitoring and reporting. • Support for Read Multiple and Write Multiple ...