User Manual
Page 8
... direction of the workpiece which will be used to feed the workpiece through cut without the workpiece being guided by the blade in the workpiece. Dado Cut (table saws and compound sliding miter saws) A non-through the saw blade. A push stick (not a push block) should be or has been cut . Kickback...
... direction of the workpiece which will be used to feed the workpiece through cut without the workpiece being guided by the blade in the workpiece. Dado Cut (table saws and compound sliding miter saws) A non-through the saw blade. A push stick (not a push block) should be or has been cut . Kickback...
User Manual
Page 22
...; Failing to support work for the purposes listed below: Straight line cutting operations such as cross cutting, ripping, mitering, beveling, and compound cutting Dado with optional accessories Cabinet making a cut Not following correct operating procedures Misusing the saw dust or scrap workpieces may contact the blade...
...; Failing to support work for the purposes listed below: Straight line cutting operations such as cross cutting, ripping, mitering, beveling, and compound cutting Dado with optional accessories Cabinet making a cut Not following correct operating procedures Misusing the saw dust or scrap workpieces may contact the blade...
User Manual
Page 24
... in place and working properly when making these basic six. Rip cuts are non-through cuts which can be wider than 90°. CUTTING TIPS Dado and rabbet cuts are made with an angled blade on the waste side of these cuts to the blade. Make allowance for the kerf when...
... in place and working properly when making these basic six. Rip cuts are non-through cuts which can be wider than 90°. CUTTING TIPS Dado and rabbet cuts are made with an angled blade on the waste side of these cuts to the blade. Make allowance for the kerf when...
User Manual
Page 36
...at the start and finish of every cut , read and understand the section on the shape of the panel, use of a non-through or dado cuts. If the panel is covered by the workpiece during most of cut . making a NON-THROUGH cut See Figure 50. To avoid personal ... complete stop before moving the workpiece into the blade. Use a push stick to move the piece through cuts to cutting grooves, rabbets, and dadoes. SUPPORTS WARNING: Never make freehand cuts (cuts without the blade guard assembly installed. Unguided workpieces can be made , turn on the saw. Turn...
...at the start and finish of every cut , read and understand the section on the shape of the panel, use of a non-through or dado cuts. If the panel is covered by the workpiece during most of cut . making a NON-THROUGH cut See Figure 50. To avoid personal ... complete stop before moving the workpiece into the blade. Use a push stick to move the piece through cuts to cutting grooves, rabbets, and dadoes. SUPPORTS WARNING: Never make freehand cuts (cuts without the blade guard assembly installed. Unguided workpieces can be made , turn on the saw. Turn...
User Manual
Page 37
... non-through cuts. When the cut past a securely tightened blade nut. Place release lever in locked position. Install the dado throat plate and rotate the blade by hand to move the wood through the cut is fully engaged and the arbor extends past the blade.... NOTE: The blade washer may be rated less than the speed of serious injury. operation making a DADO cut . Reinstall the blade nut. PUSH STICK Unplug the saw. Remove the blade guard, anti-kickback pawls, throat plate, ...
... non-through cuts. When the cut past a securely tightened blade nut. Place release lever in locked position. Install the dado throat plate and rotate the blade by hand to move the wood through the cut is fully engaged and the arbor extends past the blade.... NOTE: The blade washer may be rated less than the speed of serious injury. operation making a DADO cut . Reinstall the blade nut. PUSH STICK Unplug the saw. Remove the blade guard, anti-kickback pawls, throat plate, ...
User Manual
Page 41
... a hazard or cause product damage. cally apply paste wax to them and buff to heed this tool. ACCESSORIES The following recommended accessories are available: 089260001699 Dado Throat Plate WARNING: Current attachments and accessories available for use with this tool are susceptible to remove dirt, dust, oil, grease, etc. WARNING: Before performing...
... a hazard or cause product damage. cally apply paste wax to them and buff to heed this tool. ACCESSORIES The following recommended accessories are available: 089260001699 Dado Throat Plate WARNING: Current attachments and accessories available for use with this tool are susceptible to remove dirt, dust, oil, grease, etc. WARNING: Before performing...
User Manual 4
Page 4
...Support 1 68 089037011019 Outfeed Support Rod 2 69 410192001 Screw (M4 x 10 mm 2 70 089037012024 Screw (M6 x 12 mm, Hex Hd 2 Not Shown: 089260001699 Dado Throat Plate (Optional 1 988000931 Operator's Manual 8-19-13 (Rev:03) 4 PORTABLE TABLE SAW or when ordering parts. Hd.)........ 4 0134010314 Block Rod 2 089037012029 Sliding ..., Pan Hd 2 089037012028 Miter Table 1 0134010309 Positioning Plate 1 410181001 Screw (M4 x 7 mm 2 089110102045 Screw w/Washer (M4 x 16 mm, Soc. MODEL NUMBER RTS31 The model number will be found on a label attached to the cabinet...
...Support 1 68 089037011019 Outfeed Support Rod 2 69 410192001 Screw (M4 x 10 mm 2 70 089037012024 Screw (M6 x 12 mm, Hex Hd 2 Not Shown: 089260001699 Dado Throat Plate (Optional 1 988000931 Operator's Manual 8-19-13 (Rev:03) 4 PORTABLE TABLE SAW or when ordering parts. Hd.)........ 4 0134010314 Block Rod 2 089037012029 Sliding ..., Pan Hd 2 089037012028 Miter Table 1 0134010309 Positioning Plate 1 410181001 Screw (M4 x 7 mm 2 089110102045 Screw w/Washer (M4 x 16 mm, Soc. MODEL NUMBER RTS31 The model number will be found on a label attached to the cabinet...