Ryobi CSB135L Support and Manuals
Get Help and Manuals for this Ryobi item
This item is in your list!
View All Support Options Below
Free Ryobi CSB135L manuals!
Problems with Ryobi CSB135L?
Ask a Question
Free Ryobi CSB135L manuals!
Problems with Ryobi CSB135L?
Ask a Question
Popular Ryobi CSB135L Manual Pages
User Manual - Page 2
...HOW TO GET SERVICE: Just return the power tool, properly packaged and postage prepaid, to www.ryobitools.com. TABLE OF CONTENTS
Introduction...2 Warranty...2 General Safety Rules...3-4 Specific Safety Rules...4-5 Symbols...6 Electrical...7 Glossary of purchase, you may either repair or replace any defective part, at One World...
User Manual - Page 3
... in good condition. An undersized cord will do a job it on the saw 's applications and limitations as well as the specific potential hazards related to operate tool.
DON'T OVERREACH. Follow instructions for outdoor use of power and overheating. Feed work into moving parts. Wear hearing protection during extended periods of moving .
3 Cluttered areas and...
User Manual - Page 4
... and not making contact with incorrect size holes. of the saw . Have defective switches replaced by an authorized service center.
USE ONLY CORRECT BLADES. Do not operate tool when you are not completely understood or if in which the blade cuts completely through -sawing" operations. Repair or replace a damaged or worn cord immediately. Inspect for safe use common...
User Manual - Page 5
... the power source.
PROVIDE ADEQUATE SUPPORT to guide along the fence.
IF THE POWER SUPPLY CORD IS DAMAGED, it must be used, including all the way past the saw blade using a push stick.
SPECIFIC SAFETY RULES
NEVER perform any operation "freehand" which it can be replaced only by the manufacturer or by :
a) Keeping...
User Manual - Page 8
...blades when the workpiece is not properly supported.
GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws) A device which, when properly installed ...guided by holding it applies to prevent kickback. Freehand Performing a cut made with adjustable blades or knives.
Set The distance that serves as a guide for jointer planers) Device used to the blade other aids. The blades...
User Manual - Page 10
... to heed this handwheel to lower and raise the blade for a miter cut . A removable metal piece of the cabinet, use the tool.
10 SCALE - FEATURES
KNOW YOUR TABLE SAW
See Figure 2. The safe use of this operator's manual as well as a knowledge of this tool. carbide blade. Always keep the kerf open and prevent kickback. HEIGHT...
User Manual - Page 15
... replaced. Any such alteration or modification is securely mounted to possible serious personal injury. Failure to specific procedures explained in serious personal injury.
Parts on the floor. If shipping has influenced the settings, refer to comply could result in this manual.
If any parts are damaged or missing, please call 1-800-525-2579 for this tool...
User Manual - Page 31
... reduce the chance of this tool. OPERATION
MAKING CUTS
This table saw can cause serious personal injury.
Remove the rip fence. Set the blade to the correct depth for the workpiece. Set the miter gauge to 0° and tighten the lock knob. Make sure the wood is installed and working properly to...
User Manual - Page 32
...blade should be made , turn the saw on the miter gauge lock knob and the hand farthest from the blade
for the workpiece. Set the miter gauge to guide it. Failure to follow these instructions... the workpiece. MITER GAUGE ANGLED
MITER CUT
BLADE STRAIGHT
SCALE Fig. 36
WARNING:
Make sure the blade guard assembly is installed and working properly to full speed before turning...
User Manual - Page 34
... of the blade before turning on the saw.
When ripping a long workpiece, place a support the same height as the table surface behind the saw for the cut work.
Turn the saw on. ...; Adjust the bevel angle to the desired setting. Lock the bevel locking lever. Set the blade to the correct depth for the workpiece. Set the miter gauge to the desired angle and...
User Manual - Page 38
... identical replacement parts.
Make sure the throat plate is required.
38 If the cuts are not the same, loosen the two bolts on the fence and align it.
Retighten the two bolts.
Make two or three test cuts on the blade teeth. Clean plastic parts only with side shields during power tool...
User Manual - Page 39
... "To check and align the riving knife and saw blade installation. Cutting binds or burns work. Riving knife is warped. Always cut with convex side to table surface. Clamp screw is out of adjustment. Replace the wood. CAUSE Blade is out of balance.
Blade is dull. Replace or sharpen blade.
TROUBLESHOOTING
PROBLEM Excess vibration.
Rails are dirty or sticky.
Align...
User Manual - Page 40
... backwards. Adjust positive stops.
Blade is not plugged in.
Blade is not at your nearest authorized service center.
Height/bevel adjusting handwheel is damaged. Gears or screw post inside cabinet need adjusting (Bevel Cuts). Replace circuit fuse. Clean, sharpen, or replace blade. rip blade typically has fewer teeth.
40 TROUBLESHOOTING
PROBLEM Saw does not make accurate...
User Manual - Page 41
...'S MANUAL
10 in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
• PARTS AND SERVICE
Prior to cause cancer, birth defects, or other reproductive harm. TABLE SAW
RTS10/RTS10G
WARNING:
This product and some dust created by calling 1-800-525-2579. Replacement parts...
User Manual 4 - Page 3
... 089110113913 No Hands Warning Label 2 55 089037007909 Blade Guard Warning Label - TABLE SAW - MODEL NUMBER RTS10
The model number will be found on a label attached to the cabinet. TABLE SAW or when ordering parts. Right 1 56 089037007910 Blade Guard Warning Label - PARTS LIST FOR FIGURE A
KEY PART
KEY PART
NO. NUMBER
DESCRIPTION
QTY
1 089037007003 Throat...
Ryobi CSB135L Reviews
Do you have an experience with the Ryobi CSB135L that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Ryobi yet.
Earn 750 points for your review!