Ridgid R7111 Support and Manuals
Get Help and Manuals for this Ridgid item
View All Support Options Below
Free Ridgid R7111 manuals!
Problems with Ridgid R7111?
Ask a Question
Free Ridgid R7111 manuals!
Problems with Ridgid R7111?
Ask a Question
Popular Ridgid R7111 Manual Pages
Owners Manual - Page 1
... rugged, trouble-free performance. When properly cared for, it will give you for dependability, ease of injury, the user must read and understand the operator's manual before using this product.
WARNING:
To reduce the risk of operation, and operator safety. SAVE THIS MANUAL FOR FUTURE REFERENCE
1
OPERATOR'S MANUAL
1/2 in. DRILL
DOUBLE INSULATED R7111
Your drill has been...
Owners Manual - Page 2
... in the design of this product making its use more pleasant and enjoyable. TABLE OF CONTENTS
Introduction ...2 General Safety Rules ...3-4 Specific Safety Rules...4 Symbols...5-6 Electrical ...7 Features ...8 Assembly ...9 Operation ...9-12 Maintenance ...13-14 Accessories ...14 Warranty ...15...
Owners Manual - Page 3
... clothes, jewelry, or long hair can be repaired.
Disconnect the plug from the power source and/or the battery pack from moving parts. POWER TOOL USE AND CARE
Do not force the power tool. Properly maintained cutting tools with the switch is in . SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
Keep work to follow...
Owners Manual - Page 4
....
If the power supply cord is damaged, it must read instruction manual.
When servicing a power tool, use the next heavier gauge. When using an extension cord, be properly repaired or replaced by an authorized service center. To reduce your exposure to carry the current your hearing. SPECIFIC SAFETY RULES
Use auxiliary handles supplied with the...
Owners Manual - Page 5
...user must read and understand operator's manual before using this product.
To reduce the risk of the following symbols may be used on this tool.
Failure to keep your hands ...Watt
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
no load
Class II Tool
Double-insulated construction
.../min
Per Minute
Revolutions, strokes, surface speed, orbits etc., per ...
Owners Manual - Page 6
... extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you read thoroughly and understand completely the operator's manual. Before beginning power tool operation, always wear safety goggles or safety glasses with ANSI Z87.1. SAVE THESE INSTRUCTIONS
6 SYMBOLS
The following signal words and meanings are intended to explain...
Owners Manual - Page 7
... replacement parts when servicing. If damaged replace immediately. WARNING:
The double insulated system is intended to determine the minimum wire size required in the tool's internal wiring.
For service,...
This tool has a precision-built electric motor.
A substantial voltage drop will overheat.
Observe all normal safety precautions to a power supply that it for repair. This...
Owners Manual - Page 8
.... For ease of operation, you are attempting. DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE)
Your drill has a direction of rotation (forward/reverse) selector located above the switch trigger for extended periods of time. FEATURES
PRODUCT SPECIFICATIONS
Chuck 1/2 in this operator's manual as well as a knowledge of the project you may use the handle with either...
Owners Manual - Page 9
...:
Always wear safety goggles or safety glasses with Auxiliary Handle Assembly Chuck Key Chuck Key Holder Cord Wrap Tool Bag Operator's Manual
WARNING:
If any parts are damaged or missing do so could result in serious personal injury.
Do not be concerned; Drill with side shields when operating tools. Failure to inflict severe injury.
Failure to make you have...
Owners Manual - Page 10
... SELECTOR
(FORWARD/REVERSE) SWITCH TRIGGER
TO LOOSEN
CHUCK
DRILL BIT
CHUCK JAWS
TO TIGHTEN
CHUCK KEY
Fig. 3
CHUCK KEY HOLDER
WARNING:
Make sure to become overheated. With the drill held in figure 5. TO INSTALL BITS
See Figures 4 - 5. Unplug the drill.
Insert the chuck key and twist counterclockwise.
Open or close the chuck jaws to a point where the opening is...
Owners Manual - Page 12
... the bit and increase the drilling action.
If the bit jams in the workpiece or if the drill stalls, stop the tool immediately. When these situations occur, drill has a tendency to grab ...selector for correct setting (forward or reverse).
Secure the material to be drilled in a vise or with clamps to keep it from turning as the hole is started.
When drilling metals use a...
Owners Manual - Page 13
.... However, if you do not recommended using the provided chuck key.
Insert a 5/16 inch (8 mm) or larger hex key into the chuck of the unit under normal operating conditions.
Chemicals can now be removed and replaced with a new one.
Unplug the drill.
Open chuck jaws using this tool are lubricated with side shields during power...
Owners Manual - Page 14
... where you purchased this tool. This will tighten the chuck on the spindle and ...drill.
Open the chuck jaws.
Insert the hex key into the chuck and tighten the chuck jaws securely.
MAINTENANCE
TO RETIGHTEN A LOOSE CHUCK
The chuck may become loose on the spindle.
Open the chuck jaws and remove the hex key.
Tighten the chuck screw. Also, the chuck...
Owners Manual - Page 15
...AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase. The trademark is manufactured by other RIDGID® products may return the tool to the dealer from which vary from misuse, abuse, neglect, alteration, modification or repair by One World Technologies, Inc. The replacement tool will repair any faulty workmanship, and either repair or replace any malfunction...
Owners Manual - Page 16
... in . For the location of this tool is found on a plate attached to provide all relevant information when you , please call or visit. When ordering repair parts, always give the following information:
Model No. DRILL
DOUBLE INSULATED
R7111
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. R7111
Serial No.
983000-957
7-24-06...
Ridgid R7111 Reviews
We have not received any reviews for Ridgid yet.