Ridgid MS1250LZA Support and Manuals
Get Help and Manuals for this Ridgid item
This item is in your list!
View All Support Options Below
Free Ridgid MS1250LZA manuals!
Problems with Ridgid MS1250LZA?
Ask a Question
Free Ridgid MS1250LZA manuals!
Problems with Ridgid MS1250LZA?
Ask a Question
Most Recent Ridgid MS1250LZA Questions
Stop Pin Wont Stay Locked In Down Position
does anyone else have this problem
does anyone else have this problem
(Posted by Robpino33 7 years ago)
Popular Ridgid MS1250LZA Manual Pages
Owners Manual - Page 1
...
Your miter saw has been engineered and manufactured to our high standard for , it will give you for buying a RIDGID® product. Thank you years of injury, the user must read and understand the operator's manual before using this product. WARNING:
To reduce the risk of rugged, trouble-free performance. COMPOUND MITER SAW with Laser MS1250LZA - OPERATOR'S MANUAL
12...
Owners Manual - Page 5
...this miter saw .
ALWAYS TURN OFF THE SAW before changing blade or servicing. Disconnect your saw blade ...part of saw is too small to be replaced only by the manufacturer or by the carrying handle.
AVOID direct eye exposure when using your miter saw on and off the power switch, remove the miter saw unattended while connected to instruct other users. NEVER leave the saw...
Owners Manual - Page 7
...into your nearest AUTHORIZED SERVICE CENTER for repair.
SAVE THESE INSTRUCTIONS
Before beginning ...service we suggest you read thoroughly and understand completely the operator's manual. When servicing, use over eyeglasses or standard safety glasses with side shields and a full face shield when needed. Call RIDGID® customer service for use only identical replacement parts...
Owners Manual - Page 10
... bag
sliding MITER Fence
table extension
SAW BASE
Miter Table
10
Lower blade guard
REPEAT-A-CUT™
zero clearance throat plate Miter Scale
MITER LOCK PLATE
Positive Stop(s)
WORK CLAMP
Miter Lock Handle
Fig. 1 No Load Speed 4,000 r/min. (RPM) Input 120 V, 60 Hz, AC Only, 15 Amps Net Weight 49 lbs. Arbor Hole 1 in .
FEATURES
Product Specifications
Blade Diameter...
Owners Manual - Page 11
... pin. One end of servicing.
12 in the off and unplug the saw, then lower the saw , disconnect it in the switch trigger. To transport, turn off position.
To lock the switch, install a padlock (not included) through the hole in the down position.
wide, depending upon the angle at desired miter angles.
BLADE wrench storage...
Owners Manual - Page 12
...; - 33.9° position for clearance of the miter table.
the left and right side miter fences can be used properly, the laser guide makes accurate, precision cutting simple and easy. It ... from each side of cut(s), then wipe the mark off with your compound miter saw is larger providing additional support.
Simply mark the fence with a pencil, make the desired number of the...
Owners Manual - Page 13
...
Fig. 7
WARNING:
The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.
13 LOOSE PARTS
The following items are included with your Compound Miter Saw:
Miter Lock Handle
Washer (2)
Dust Bag
Blade Wrench
Dust Guide
Hex Key, 1/16 in.
Work Clamp
...
Owners Manual - Page 14
...miter fence during use with the saw arm secured in the saw base for this tool or create accessories not recommended for use . If any parts are replaced. To release the saw arm, push down position. Warning:
If any parts are damaged or missing, do not operate this manual... lift saw from the carton by the handle. If shipping has influenced the settings, refer to specific procedures ...
Owners Manual - Page 19
... throat plate to allow the blade to reach full speed, then carefully make a straight cut the slot, set your saw . Next, adjust the bevel angle to a complete stop before raising the saw . Place one -half turn saw on and allow the blade to come to 45°, turn your saw at 0° miter, turn .
Depress the miter lock plate...
Owners Manual - Page 22
... is play in the pivot joints, have saw arm to do not require readjustment. Never operate your miter saw on the floor or in the pivot, have saw without holding workpiece against the fence). WARNING:
To avoid serious personal injury, keep your compound miter saw repaired at your nearest AUTHORIZED SERVICE CENTER. at least 3 in serious personal injury...
Owners Manual - Page 23
...lumber or molding, support the opposite end of workpiece. NOTE: You can quickly locate 0°, 15°, 22.5°, 31.6°, and 45° left to make sure that no problems will occur when...possible.
Before turning on the saw, perform a dry run of the cutting operation just to loosen.
Press the miter lock plate down with the miter table set at some angle other than zero.
...
Owners Manual - Page 28
...;, therefore, you will need to fit properly, crown molding must be set left 31.6° 3. Miter table set at 31.6° either right or left end of molding against fence 2. Miter table set right 31.6° 3. OPERATION
cutting crown molding
Your compound miter saw . In general, compound miter saws do not have angles of a room are interdependent; The two...
Owners Manual - Page 29
... left end of cut
Left side, outside corner 1. Miter table set right 45° 3. OPERATION
MAKING A CROWN MOLDING SUPPORT JIG
A crown molding support jig will pinch the blade near the completion of the cut the wood to this method, the saw blade to the desired setting. NOTE: A separate support jig must be made for corners that are...
Owners Manual - Page 31
... safety and reliability, all repairs should be damaged by a qualified service technician at any other . Reassemble using solvents when cleaning plastic parts. warning:
Always wear safety...damage from various types of carbon remaining. Brush REPLACEMENT
See Figure 38.
Brush assembly is required: Unplug the saw could result in .
Do not overtighten. Therefore...
Owners Manual - Page 34
...:01)
34 COMPOUND MITER SAW with Laser MS1250LZA - Be sure to the motor housing. For the location of this tool is found on a plate attached to provide all relevant information when you , please call or visit.
Please record the serial number in . When ordering repair parts, always give the following information:
Model No.
OPERATOR'S MANUAL
12 in the...
Ridgid MS1250LZA Reviews
Do you have an experience with the Ridgid MS1250LZA that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Ridgid yet.
Earn 750 points for your review!