Rane AC 23S Support and Manuals
Get Help and Manuals for this Rane item
Rane AC 23S Videos
3-way active system: 3x Fredy 408, Eximus DP1, Rane AC23S, Klipsch CW III, Beyma TPL-150H, Raal
Duration: 3:17
Total Views: 364
Duration: 3:17
Total Views: 364
Eximus DP1, Rane AC23S, Klipsch Cornwall III, Beyma TPL-150H, Raal 140-15D, 3x Fredy 408
Duration: 3:06
Total Views: 1,408
Duration: 3:06
Total Views: 1,408
Popular Rane AC 23S Manual Pages
Operation Manual - Page 1
...
4.5k
250
5.8k
190
7.0k
HIGH
LEVEL 46
2
8
0 10
LOW
LOW / MID
4W: INACTIVE 5W: HIGH-MID
4W: INACTIVE 5W: HIGH-MID / HIGH
HIGH
POWER
AC 23S
ACTIVE
CROSSOVER
AC 23S
ACTIVE CROSSOVER
Operation Manual - Page 4
... Channel 1 only. WEAR PARTS: This product contains no wear parts. or 3-Way Stereo mode. Set the STEREO/MONO switch appropriately. The fact that the Channel 1 and 2 switches are set for 5-Way.
Manual-1 To operate the unit in Stereo 3-Way mode, be sure the rear panel switches are set to chassis ground. OPERATORS MANUAL
AC 23S
ACTIVE CROSSOVER
CH 1
MASTER LEVEL
46...
Operation Manual - Page 5
... 5W: HIGH-MID
4W: INACTIVE 5W: HIGH-MID / HIGH
HIGH
POWER
AC 23S
ACTIVE
CROSSOVER
1
�
345 6 7 2
�
345 6 7 8
Observe the labels above the controls for stereo operation.
*Not used for all signal is situated behind the low frequency diaphragm. Refer to 'Setting the Output Level Controls' on and ready. When this channel. Unity gain...
Operation Manual - Page 6
... inlet. This switch removes the Low frequency crossover from the signal path. If you need a summed Mono Low Ouput, see 'Monoing the Low Outputs' on page Manual-15.
5 STEREO / MONO switch: Set this row Right Input
1 Left Input
100-240 V
COMMERCIAL AUDIO
50/60 Hz 7 WATTS EQUIPMENT 24TJ
AC 23S
MADE IN U.S.A. Note: The Low frequency...
Operation Manual - Page 7
...: INACTIVE 5W: HIGH-MID / HIGH
HIGH
POWER
AC 23S
ACTIVE
CROSSOVER
1 345 6 789 0 q 2 345 6 789 0 q w
Observe the labels screened above the controls for stereo operation.
1 Channel 1 MASTER LEVEL control: Sets the overall Level of Channel 1 without altering the relative settings of the Low/Mid/ High Outputs.
3 LOW LEVEL control: Sets the Level of signal going to this...
Operation Manual - Page 8
... Manual-15.
6 STEREO / MONO switch: Set this to the STEREO (out) position.
7 STEREO 2‑Way / 3‑Way switches: Set both Channels to the 3-Way position.
8 MONO 4‑Way / 5‑Way switch: Set ... signal source to this row Right Input
1 Left Input
100-240 V
COMMERCIAL AUDIO
50/60 Hz 7 WATTS EQUIPMENT 24TJ
AC 23S
MADE IN U.S.A. PIN 2: POSITIVE PIN 3: NEGATIVE PIN 1: CHASSIS GND
...
Operation Manual - Page 9
...5W: HIGH-MID / HIGH
HIGH
POWER
AC 23S
ACTIVE
CROSSOVER
1 234 5 0qw e � 678 9 rty u i o
Observe the labels screened below the controls for your system.
6 LOW LEVEL control: Sets the Level going to the Mid Output only...MONO 4-Way" on the back panel. Refer to pages Manual-9-12 for all signal from 0 to 2 ms of their settings when the AC 23S is lit, then the unit ready to MIN (minimum...
Operation Manual - Page 10
...with Part 15 of the high frequency (tweeter) amp.
7 STEREO / MONO switch: Push this device must accept any interference received, including interference that may cause undesired operation. Manual-7 ...switch: set as determined by the HIGH-MID / HIGH FREQUENCY control, and is not used in this Output when using the AC 23S as a Mono 4-Way Crossover. In 4-Way the AC 23S internally bypasses...
Operation Manual - Page 11
... row
8 79 8
1 Input
100-240 V
COMMERCIAL AUDIO
50/60 Hz 7 WATTS EQUIPMENT 24TJ
AC 23S
MADE IN U.S.A. REAR PANEL: ALTERNATE MONO 4-WAY CONNECTIONS
Mono 4-way connection labels are in the 5-Way position. By connecting a patch cable from the CHANNEL 1 HIGH OUT to the CHANNEL 2 INPUT, the LOW / MID crossover range changes from the CHANNEL...
Operation Manual - Page 12
... AC 23S possesses 24 dB/octave roll-off, so the crossover points may be set to panic, for further alignment details. If at and beyond the recommended performance range.
This forms a "lobe" or radia- But to make a sound
system a real headache to verify the exact setting. This rampant lobing error can be sure that all drivers are...
Operation Manual - Page 13
... that the high driver is actually in the AC 23S is unnecessary.
6. Now the drivers are properly phase aligned and no delay is physically altered. Place the analyzer mic about 15 feet in balancing the speaker stack. Turn up as well to restore dispersion close to ±3 dB (not necessary with your specific crossover points than...
Operation Manual - Page 14
... folded or straight horns, resulting in the AC 23S is designed to the LOW DELAY control occurs at all of the two speakers sharing the crossover point is unnecessary. The amount of displacement corrections available from the delay depends on the SPL meter to the mid driver then only worsens the situation.
adding delay...
Operation Manual - Page 16
...driver or horn roll-off, bass roll-off problem. Manual-13
This means setting up the LOW LEVEL control on an analyzer at several other locations and adjust the crossover as set previously.
2. Setting...necessary to highest, so that a good active crossover can deliver. Run pink noise through the system, either through the low frequency drivers (it should sound like a parametric ...
Operation Manual - Page 17
...driver response.
9. Minimize all of the MUTE switches on the crossover, and check that noise is probably due to all amplifier level controls are set... controls in the system. Manual-14 Adjust the SPL meter and/or crossover output until there is a...crossover output LEVEL controls are present.
4. Setting Levels Using an SPL Meter & Pink Noise Generator
The MUTE switches on the AC 23S...
Operation Manual - Page 18
...C72 and C98 on the underside of the CD driver's frequency response. Replace the top and bottom covers.
3 dB Down ...Rane Corporation 10802 47th Ave. Monoing the Low Outputs
It is possible to the J9 position.
3. Move the MONO SUB OPTION header to mono the Low Frequency Outputs of the AC 23S by an internal jumper. Set...service personnel.
1. Find the point where the high end starts to install...
Rane AC 23S Reviews
We have not received any reviews for Rane yet.