RCA ANT3037XR Support and Manuals
Get Help and Manuals for this RCA item
View All Support Options Below
Free RCA ANT3037XR manuals!
Problems with RCA ANT3037XR?
Ask a Question
Free RCA ANT3037XR manuals!
Problems with RCA ANT3037XR?
Ask a Question
Popular RCA ANT3037XR Manual Pages
Instruction Manual - Page 1
For your safety, follow the installation instructions.
1
BEFORE YOU START!!! Please read the IMPORTANT SAFETY INFORMATION sheet included in this antenna near power lines is dangerous.
WARNING
Installation of this package. ENGLISH
ANT3037X Outdoor Antenna
Installation Manual
Point Toward Stations
Mast not included with antenna.
Instruction Manual - Page 2
Parts List
Back Assembly (VHF)
Front Assembly (UHF)
Washer (6) Corner Reflector (2)
Small Flange Nut (6) Large Screw (2)
Mast Clamp Insert
Matching Transformer
U-Bolt
Large Flange Nut for U-Bolt (2)
Low Band VHF Add-On Kit For RF Channels 2-6 and/or FM (Not Needed for Most Installations, See Page 3.)
Large Screw Clip
Element Extension...
Instruction Manual - Page 3
... any low band VHF channels in one or two directions.
Each of these sites has a feature that allows you move the antenna.
3
Do I Need to 65 miles when installed outside this antenna, determine which channels you want FM reception, then you determine the best location and direction to change the reception. For most...
Instruction Manual - Page 4
...
Fold out Elements
After
Unfolded Elements
Boom
Figure 2
Boom
Phasing Lines
On the back assembly, remove the nut and screw from the boom.
Assembling the Antenna
Start by unfolding the VHF elements on the front assembly until the elements are perpendicular to the boom. See Figure 2. You should hear the pieces...
Instruction Manual - Page 7
... steps on the next page.
Adding the Low Band VHF Add-On Kit
For RF Channels 2-6 and/or FM
If unsure whether or not to install the Low Band VHF Add-On Kit, see the section "Do I Need to...
Instruction Manual - Page 8
Insert the large screw through the hole in the bottom of the antenna (Figure 12).
The shortest element extension will connect to the shortest element ... element. The element extensions should decrease in both parts align.Thread a small flange nut on the back assembly, and the longest element extension will connect. Then, install the clip onto the element extension with crimped ends...
Instruction Manual - Page 9
... to Align
Figure 13
After
Top Bottom
Attaching a Coax Cable
Locate the two posts on each screw. Slide one fork of the matching transformer between a set of each hole, and thread a small flange nut onto each post. Posts
Figure 14
9 Align the holes in the element sleeve and element. Place...
Instruction Manual - Page 10
... antenna.
• Point the front of antenna toward stations.
• Tape downlead to mast to prevent wind whipping.
The holes in place. Tighten the nuts until the U-bolt securely holds the mast in both parts ...U-bolt. The mast should align. The U-bolt assembly will slide over the coax cable and install the connector. If your coax cable has the connector already on it, you will need to ...
Instruction Manual - Page 11
...close as per National Electrical Code, ANSI/NFPA 70
Ground Clamp
Antenna Lead-In Wire
Grounding Conductors (NEC Section 810-21) Electric Service Equipment
Ground Clamps
Antenna Discharge Unit (NEC Section 810... Drip Loop On Lead-In To TV
Power Service Grounding Electrode System (NEC Art 250, Part H) NEC -
Example of a "ground up" antenna installation, it may not be necessary to ground the...
Instruction Manual - Page 12
..., available at 1-800-290-6650 or visit RCAAudioVideo.com. Amplifying the Signal
The signal received at the antenna is all the signal the system will ever have questions, contact RCA at many retailers or from RCAAudioVideo.com.
12 An amplifier or pre-amplifier may be required if any...
Instruction Manual - Page 13
...the TV set and the output channel of the connections or the cable between the converter and television may be obstructing the signal. Try the antenna in the picture.
Try moving the antenna to ...antenna. Try turning the antenna 10 or 20 degrees in the picture. Try running a new channel scan on the same channel. This is often caused by a weak or intermittent signal. ENGLISH
Troubleshooting...
Instruction Manual - Page 14
...nature, alteration, improper installation, mishandling, misuse, neglect, or accident.
THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, ...the Company's option) without charge for parts and repair labor. This Warranty is not transferable and does not cover product purchased, serviced or used outside the United States or...
RCA ANT3037XR Reviews
We have not received any reviews for RCA yet.