Pyle PSTMP95 Support and Manuals
Get Help and Manuals for this Pyle item
View All Support Options Below
Free Pyle PSTMP95 manuals!
Problems with Pyle PSTMP95?
Ask a Question
Free Pyle PSTMP95 manuals!
Problems with Pyle PSTMP95?
Ask a Question
Most Recent Pyle PSTMP95 Questions
Steam Press Power Supply Board Damaged
Hi there my steam press power supply board damaged where can i get the new one? many thank
Hi there my steam press power supply board damaged where can i get the new one? many thank
(Posted by farhadbehjani 2 years ago)
Popular Pyle PSTMP95 Manual Pages
User Manual - Page 1
USER MANUAL
PSTMP95
Digital Table Top Steam Press
User Manual - Page 2
CONTENTS
Features of the Elite 1 Safety Reminders 2 Part Identification 3-4
Steam Press Operation
Preparation for use 5 Filling the water tank 5 Turning on the power 5 Selecting the temperature 6 Steam Control Notes 7 Pressing 8 Finishing Pressing 9 Cleaning 10
Suggestion for Success 11 Use of the Pressing Cushion 12 Techniques for Pressing 13-14 Troubleshooting 15-16
User Manual - Page 3
... 26.7 x 10.2 x 22.0 inches Ÿ Weight: 26.4 Lbs.
1 Digital Table Top Stream Press
Ÿ 50% Faster Than Traditional Ironing Ÿ Safe for Nylon, Silk Rayon, Wool...Ÿ 'Steam Burst' Function Blasts Away Wrinkles Ÿ Advanced Digital Control Center Ÿ Variable Temperature Selection Ÿ Quickly Steam Press and Remove Wrinkles Ÿ Multiple Dry-Heat & Steam Settings for Different ...
User Manual - Page 4
...the appliance if it to an authorized service center for repair. Ø Do not operate another ...parts, hot water or steam. Ø This appliance is not intended for use by young children or infirm persons unless they have the cord repaired...; Be careful. SAVE THESE INSTRUCTIONS
2 THIS UNIT IS FOR HOUSEHOLD USE ONLY. SAFETY REMINDERS
WARNING
Read all of the instructions and then save them for...
User Manual - Page 5
... is filled through the front of steam when pressed.
4. PART IDENTIFICATION
1. The Pressing Handle raises and lowers the Pressing Plate. The Locking Knob will only be seen through holes in the top. The Red Steam Burst Button on the three highest settings. 11. The [ POWER ] button to carry or store the Steam Press.
3. The Water
Level can be available...
User Manual - Page 7
... open position allowing free
movement of the unit.
Be careful to the fully raised (up ) position. Lift the Pressing plate to avoid spilling water onto the Steam Press when filling. STEAM PRESS OPERATION
STEP1 - PREPARATION FOR USE Set the appliance on a sturdy work surface. Using the Water Container, slowly pour the distilled water into an electric...
User Manual - Page 9
... your garment.
7 Do not use the Steam Burst function when the steam press is ready to flow. IMPORTANT NOTE: Do not press the Steam Burst Button for some time, lift the Pressing plate into the raised position and press the Steam Burst Button several times until the steam begins to produce steam. The Yellow Steam Ready Light will come on . IMPORTANT...
User Manual - Page 10
... the fabric a burst of the Pressing Plate(A) and lower it is in the open the press. b. For light duty Pressing, simply lowering the handle and allowing the Pressing Plate to the up
position. Lower the pressing plate until the Pressing Plate is set high enough you may fully lower the pressing plate. Press the Steam Burst Button for about two...
User Manual - Page 11
..., because it in open position. This should be drained by pressing the Steam Burst Button until all of the Ironing Board. FINISHING PRESSING/STORING THE UNIT a. c. STEP 7 - b. d. e. ...Locking Knob to cool completely (approximately 30 minutes). f. Water may be stored for the Steam Press to the locked position. However, it is recommended that if the machine will go ...
User Manual - Page 12
... NOT use any abrasives on , gently lower the Pressing Plate onto the Pressing Cushion. You can clean the surface with mild detergent and warm water.
10 CLEANING (As needed)
a. This Pressing Plate has a non-stick coating that will assist in the center of steam. Set the Steam Control and Temperature Control to 7 times. With water in...
User Manual - Page 13
.... SPRAY BOTTLE METHOD: Using a Spray Bottle, lightly spray the garment before placing it to escape. Take care with a press cloth BEFORE pressing. This will help protect delicate accessories and fasteners. Lower the heat or steam settings, place the items FACE DOWN on the Ironing Board. Repeat the procedure until the fabric is dry.
11...
User Manual - Page 14
... etc. You MAY DAMAGE the Steam Press by doing so. b. c. Make sure the area to be pressed flat. E. a. d. IMPORTANT NOTE: Do not attempt to lower the Pressing Plate to shape tailored garments. Place the area to be pressed is supplied with your Steam Press for use with the Pressing Cushion in place. Raise the Pressing Plate after a few seconds...
User Manual - Page 17
... button again.
15 Temperature Setting is not listed here:
PROBLEM
Steam Press cannot be opened using Pressing Handle.
Plug the appliance in Locked position. Temperature has not been selected. Gradually increase the temperature until obtaining the desired results. Automatic Shut-Off has engaged. TROUBLE SHOOTING
Below is not plugged into an outlet. Steam Press becomes warm but Does...
User Manual - Page 18
PROBLEM No Steam.
CAUSE
SOLUTION
Water Level is too thick to use spray misting bottle as directed. Controls have not been properly set.
Don,t press the Steam Button more than 5 seconds continuously. Item on thicker items. Use added steam for wrinkles.
16 Fill the water tank. If suitable for the Steam Ready Light to a higher temperature.
Steam Button has...
User Manual - Page 19
...service department at pyleaudio.com or
send an e-mail to [email protected] including your product for one (1) year from the date of Sound Around Inc. Our Obligation under this warranty is limited to the repair or replacement of the defective unit when it is limited to the review... letter indicating the problem you are carefully constructed and thoroughly tested before shipment.
Pyle PSTMP95 Reviews
We have not received any reviews for Pyle yet.