Pyle PLMRC500X1 Support and Manuals
Get Help and Manuals for this Pyle item
View All Support Options Below
Free Pyle PLMRC500X1 manuals!
Problems with Pyle PLMRC500X1?
Ask a Question
Free Pyle PLMRC500X1 manuals!
Problems with Pyle PLMRC500X1?
Ask a Question
Popular Pyle PLMRC500X1 Manual Pages
Instruction Manual - Page 2
...service center should be followed precisely. It is better to the cables, take care that they do not pass sharp edged metal. Before installing the power ampli er please read these instructions... in the boot and under the key dashboard, as this instruction manual carefully.
Note that the ampli er generates heat so that ...the set can be carried out easily and safely byway of the...
Instruction Manual - Page 3
...amperage fuse. www.PyleUSA.com 3 FUSE REPLACEMENT
If the fuse blows, check the power connection and replace the fuse.
If the fuse blows again after replacement, there may cause serious damage. PROTECTION ...occur in
temperature inside the car, allow the unit to cool o before operation.
• When installing the unit horizontally, be sure not to cover the heatsink ns
with an impedance of 1 to...
Instruction Manual - Page 4
... ampli er. For most applications # 18 gauge wire should be used for this application. WIRING INSTRUCTIONS
POWER CONNECTION The battery terminal (BATT) must be connected directly to the positive terminal of the ...this lead and connect it between the ground terminal (GND) of the ampli er and a metal part of the vehicle.
4 www.PyleUSA.com Do not ground any other wiring is also critical to...
Instruction Manual - Page 6
... power input lead only after all other leads have been
connected.
• Be sure to connect the ground wire of the unit securely to a metal part of the car. • A lose connection may cause amalfunction of the unit respectively must be larger than 10 - Standard 20 GAUGE is ne and the...
Instruction Manual - Page 7
... to2/3 of the radio. SUBSONIC FILTER The higher frequency above setting point can be made for timing di erences between drivers. the ampli er will also switch o automatically - Choose the...connections have been made correctly.
www.PyleUSA.com 7 OPERATION
After the ampli er has been installed and all connections have been made carefully and securely, turn the radio ON so that you...
Instruction Manual - Page 8
... cm from the ground point. Route the ground cables from the radio and all other equipment parts, like equalizer, active crossover network or other substance from the battery. Now when turning ON ...er automatically switches ON and OFF. ln doing so, drill a hole in auto fuse protecting the set against fault conditions.
FUSE The ampli er is equipped with a higher value and never bridge the ...
Instruction Manual - Page 9
...correctly (=terminaI + I2V/GND/REM). If you use a 1 Ohm speaker and the set is free of trouble. No Stereo Sound and Weak Bass Speaker cables (+) and (-) are not connected correctly.
... speakers are overloaded, therefore turn the gain control to the correct value of a new fuse! TROUBLESHOOTING
No Function The connection cable is lit The plus and minus wires of the speaker cable have ...
Instruction Manual - Page 10
... the
ampli er and RCA or DIN output of a ground loop
isolator may solve the problem.
10 www.PyleUSA.com The REM cable to the automatic antenna output of corrosion and have...voltage is often interference caused by the generator (piping), ignition (cracking) or other car electronic parts. INTERFERENCE
All cables can nd the best central point in measuring the voltage directly at the ...
Instruction Manual - Page 11
...: • Mono Block Audio Amp System • Weather Resistant Class D Compact Ampli er • IPX4 E ect • Integrated Power Wiring Harness • Perfect for Custom Installations & Applications • Ability to Connect & Stream Audio from External Devices • Speaker Wiring Connectivity • Soft Turn On/O • Overload & Power Protection Circuitry
What's in...
Instruction Manual - Page 12
Questions? We are here to help! Phone: (1) 718-535-1800 Email: support@pyleusa.com Issues?
Pyle PLMRC500X1 Reviews
We have not received any reviews for Pyle yet.