Pyle PLMRA430BT Support and Manuals
Get Help and Manuals for this Pyle item
View All Support Options Below
Free Pyle PLMRA430BT manuals!
Problems with Pyle PLMRA430BT?
Ask a Question
Free Pyle PLMRA430BT manuals!
Problems with Pyle PLMRA430BT?
Ask a Question
Most Recent Pyle PLMRA430BT Questions
High Input 4conductor Plug
where do I get the 4 conductor plug for the high input on the PLMRA430BT Plyle amplifie
where do I get the 4 conductor plug for the high input on the PLMRA430BT Plyle amplifie
(Posted by trank39342 1 year ago)
Popular Pyle PLMRA430BT Manual Pages
User Guide - Page 1
... and repair. Install in accordance with the defective unit. Damage caused by insufficient support is likely to undergo excess vibration through use protective plastic cups or washers before reconnecting to enter the amplifier. To prevent damage to humid location, condensation may occur inside. You will be obtained from an authorized Pyle Audio service center. Elite Series...
User Guide - Page 2
...or cold can cause premature wear of parts. which can shorten the life of electronic devices and distort or melt plastic parts. After all the wiring.
Testing ... adjust the gain control to match the output level of your radio:
(A) Set the volume control on . Maintenance
Keep the amplifier dry. Handle the amplifier ...Elite Series Waterproof Amplifiers Dropping it dry immediately.
User Guide - Page 4
... speaker wires that vary among the various models in the amplifier line availability. Be sure to run at battery. (Fuse preferably installed 1 foot
within 1 foot from the battery). The amp can support an impedance load as low as 2 ohms per
channel or 4 ohms in crossover use. The Pyle Elite Series Amps feature options and configurations...
User Guide - Page 5
.../equalizer output using RCA type connector cables. Stereo Input Connection - Elite Series Waterproof Amplifiers
Mono Input Connection RCA Type Terminals Bridge-Ability *Not available on all PLMRA amp models.
RCA Type The Elite Series Amps feature plated RCA terminals for detailed model information, specific model wiring and connection ability. Couple the RCA input with line level...
User Guide - Page 7
... in this manual to your system levels correctly! Models: PLMRA210BT, PLMRA410BT, PLMRA430BT, PLMRA630BT, PLMRA830BT
Elite Series Waterproof Amplifiers
Connect the 'Remote' of an amplifier to noise conditions when you will use more than one source of the stereo unit. Bridging is done by doing so, they want their amplifiers. Please follow the instructions found in...
User Guide - Page 11
... directly to the corresponding speakers. Connect the GND pole of power supply directly to chassis of handling high power. Elite Series Waterproof Amplifiers To make a good grounding and prevent motor boating noise problem connect another 12 gauge minimum wire from battery). 2. Connect the 'Remote' pole to the receiver power antenna lead. PLMRA410BT...
User Guide - Page 12
Wiring
Power Connection
Elite Series Waterproof Amplifiers PLMRA430BT -
User Guide - Page 13
Elite Series Waterproof Amplifiers Wiring
4 Channel Input Connection Low Level Inputs
2 Channel Input Connection Low Level Inputs
High Level Wiring
4 Channel Connection Floating Ground
Visit www.PyleAudio.com for detailed model information, specific model wiring and connection ability. PLMRA430BT -
User Guide - Page 14
Wiring
4 Channel Mono Connection Low Level Inputs
2 Channel Connection Low Level Inputs
4 Channel Mono Connection Floating Ground
Elite Series Waterproof Amplifiers PLMRA430BT -
User Guide - Page 15
PLMRA430BT - Wiring
4 Channel Output Mode
Bridged Dual Mono Output
2-8 Ohm
4 Channel Stereo Output Mode with Mono Bridged Subwoofer Output
Elite Series Waterproof Amplifiers
4-8 Ohm
User Guide - Page 16
PLMRA630BT - Wiring
Elite Series Waterproof Amplifiers
User Guide - Page 22
...Pyle amp. Your amp comes with any wires, lines or other devices within your vehicle's safety features, wiring or other Bluetooth-enabled device, the Bluetooth amp network name will not require a password to install... note of the mounting holes to adjusting volume controls --
Elite Series Waterproof Amplifiers Elite Series Bluetooth Connection When searching for the amp via your ...
User Guide - Page 23
...short circuit, or extreme temperature conditions. Elite Series Waterproof Amplifiers or speaker short ... system to determine the source of the problem. • If the shutdown was a...faulty, please contact Pyle technical support, or consult the...install under the supervision of these conditions, the Protection LED will disable the amplifier if it senses an input overload. When replacing...
User Guide - Page 24
...switches to the other side, the problem is supplying output signal. Before making...they are secure and tight. Elite Series Waterproof Amplifiers Troubleshooting
No output. Only one ... in a pinched condition, or likely to replace the power fuse, do so with the amplifier...set to its midpoint If you need of the disconnected RCA plugs with the R). Briefly tap the center pin of each of service...
User Guide - Page 25
Models & Specs Elite Series Waterproof Amplifiers Pyle Elite Series -
Pyle PLMRA430BT Reviews
We have not received any reviews for Pyle yet.