Pyle PINV4 Support and Manuals
Get Help and Manuals for this Pyle item
Popular Pyle PINV4 Manual Pages
PINV4 Manual 1 - Page 2
... is designed for indoor use of this inverter to power utility AC distribution wiring under any AC outlet. • The PINV4 / PINV5 / PINV6 is connected to maintain at least 2-inch (5cm) air space on all CAUTION and WARNING statements. Improper use only and not recommended for purchasing the PYLE View DC to serve such as normal household wall...
PINV4 Manual 1 - Page 3
PROTECTION LED 5. FEATURES PINV4 / PINV5 / PINV6
1. POWER ON LED 4. ON/OFF SWITCH 3. AC OUTLET 2. BINDING POST TERMINAL
2
PINV4 Manual 1 - Page 4
... and DC power outlets. When continuously powering loads rated higher than 600 Watts, connect the inverter directly to a 12 Volt battery, please use the system with certain power tool battery packs. D. Be sure to fasten all connections between 10.3 to 15.6 Volts DC and must be a battery or a well-regulated 12V/30A DC power supply. Turn off the PINV4 / PINV5 / PINV6 power...
PINV4 Manual 1 - Page 5
... connect the inverter to any AC load circuit in : When operated from the directly connection to a 12 Volt battery (PINV4 / PINV5 / PINV6) Any combination of 115 Volt AC products with a total power consumption of 600 Watts or less for overload, low battery voltage and overheat fault conditions. This manual reset feature prevents unexpected or hazardous restarting of DC (battery...
PINV4 Manual 1 - Page 6
... capacity should be selected based on the desired operating time. The alarm sounds. The inverter can operate whether or not the vehicle's engine is strongly recommended to start the vehicle...reverse polarity The low voltage battery (below DC 10V)
The high input voltage (over DC 15.6V) The overload The overheat
PROTECTION
The fuse blown. Operating the inverter from a vehicle battery until the low ...
PINV4 Manual 1 - Page 7
...) .
POSSIBLE CAUSES The fuse of inverter is discharged (alarm sounds) The inverter overheated
Recharge battery. TROUBLE SHOOTING
SYMPTOM A: NO AC POWER OUTPUT, THE RED LED LIGHTS. Replace fuse.
Turn off the inverter and allow to a power source with a total power rating
(PINV4) , 800 Watts (PINV5) or 1000 Watts (PINV6), the
less than 600 Watts Use the product with correct voltage...
PINV4 Manual 1 - Page 8
... poor battery condition Inadequate power of excessive voltage drop
SUGGESTION Recharge battery Check condition of battery clips and terminals. SYMPTOM C: THE LOW OUTPUT OF INVERTER IS MEASURED
POSSIBLE CAUSES Battery voltage is too low below 10V DC The inverter is overload
SUGGESTION Recharge battery Reduce load to 600 Watts (PINV4) , 800 Watts (PINV5) and 1000 Watts (PINV6) maximum to...
PINV4 Manual 1 - Page 9
SPECIFICATIONS
AC output voltage (nominal 115 Volts AC DC input voltage range 10-15 Volts DC Maximum Continuous AC output power 600 Watts (PINV4) ...800 Watts (PINV5) ...1000 Watts (PINV6) Maximum AC output surge power 1200 Watts (PINV4) ...1600 Watts (PINV5) ...2000 Watts (PINV6) AC output frequency 60 Hz +/- 2 Hz AC output waveform modified sine wave No load current draw less than 0.7A (...
Pyle PINV4 Reviews
We have not received any reviews for Pyle yet.