Pyle PINV3 Support and Manuals
Get Help and Manuals for this Pyle item
Popular Pyle PINV3 Manual Pages
PINV1 Manual 1 - Page 2
... become
uncomfortably warm, reaching 140˚F (60˚C) under extended high power. • Disconnect power to the inverter when it is not in excess of this inverter to power utility AC distribution wiring under any AC outlet. • The PINVI / PINV2 / PINV3 is designed for indoor use only and not recommended for purchasing the PYLE View DC to AC Power Inverter.
PINV1 Manual 1 - Page 3
POWER ON LED 4. POWER ON LED 4. PROTECTION LED 5. FEATURES
PINV1
1. AC OUTLET 2. PROTECTION LED 5. BINDING POST TERMINAL
2 AC OUTLET 2. ON/OFF SWITCH 3. ON/OFF SWITCH 3. LIGHTER PLUG
PINV2 / PINV3
1.
PINV1 Manual 1 - Page 4
... (-) terminal and RED battery chip to 150 Watts. Do not use the provided battery clip cables (PINV2/ PINV3) to connect the inverter directly to operate the load. OPERATION
- To obtain the power source must be able to supply the necessary current to the 12 Volt power source. The power source may cause permanent damage to deliver: (150...
PINV1 Manual 1 - Page 5
... DISTRIBUTION WIRING. GREEN : It indicates the inverter is power on one end of the PINV1, PINV2 and PINV3, make sure of 300 Watts or less for PINV3. B. RED : It indicates the inverter shutdown caused by switching OFF for connection directly to standard electrical and electronic equipment.
• Do not connect the inverter to household or RV AC distribution wiring...
PINV1 Manual 1 - Page 6
... charge level of two to recharge battery before its capacity and the power level drawn by the particular AC load.
The vehicle batteries are not intended for constant deep...sounds will vary depending on the desired operating time. The unit auto shutdown.
The inverter can be expected with a 300 Watt load.
The alarm sounds. The unit auto shutdown. The use of a deep discharge...
PINV1 Manual 1 - Page 7
...400 Watts (PINV3), the high starting surge causes the overload shutdown. SYMPTOM B: NO AC POWER OUTPUT, NO LED LIGHTS ARE ON.
TROUBLE SHOOTING
SYMPTOM A: NO AC POWER OUTPUT, THE RED LED LIGHTS. Clear blocked fan (PINV2 / PINV3) or remove the objects covering the ventilation.
Use the product not exceeds the inverter's surge capacity, 300 Watts (PINV1) , 600 Watts (PINV2) and 800 Watts (PINV3...
PINV1 Manual 1 - Page 8
... drop
SUGGESTION Recharge battery Check condition of battery clips and terminals.
SYMPTOM C: THE LOW OUTPUT OF INVERTER IS MEASURED
POSSIBLE CAUSES Battery voltage is too low below 10V DC The inverter is overload
SUGGESTION Recharge battery Reduce load to 150 Watts (PINV1) , 300 Watts (PINV2) and 400 Watts (PINV3) maximum to maintain regulation. Clean or replace as necessary
7
PINV1 Manual 1 - Page 9
individual units might vary. Specifications are typical; SPECIFICATIONS
AC output voltage (nominal 115 Volts AC DC input voltage range 10-15 Volts DC Maximum Continuous AC output power 150 Watts (PINV1) ...300 Watts (PINV2) ...400 Watts (PINV3) Maximum AC output surge power 300 Watts (PINV1) ...600 Watts (PINV2) ...800 Watts (PINV3) AC output frequency 60 Hz +/- 2 Hz AC output waveform ...
Pyle PINV3 Reviews
We have not received any reviews for Pyle yet.