PEXA3000 Manual 1
Page 2
... low Level controls set too low SOLUTIONS Check AC connections and switches Check and replace fuses at plug and IEC socket. Use the original packaging to the national distributor for your name and address, details of the problems, date code and date and place of excellent service. Power connected equipment from the same AC outlet where possible Use only high quality cables of Contents Overview 2 Important Safety Instructions 2 Front Panel 3 Rear Panel 4 Installation...
... low Level controls set too low SOLUTIONS Check AC connections and switches Check and replace fuses at plug and IEC socket. Use the original packaging to the national distributor for your name and address, details of the problems, date code and date and place of excellent service. Power connected equipment from the same AC outlet where possible Use only high quality cables of Contents Overview 2 Important Safety Instructions 2 Front Panel 3 Rear Panel 4 Installation...
PEXA3000 Manual 1
Page 3
... should be serviced by qualified service personnel when: A.The power-supply cord or the plug has been damaged; Object have superior sound quality and incredible reliability. Improper installations of this product near water-for example, near children. (3)Do not use . (11) Care should be connected to rain; Page 2 PEXA SERIES Technical Specifications Model Stereo Mode (Both channels driven) 1KHz Bridge Mono Mode 1KHz 4 Ohms 8 Ohms 8 Ohms FREQUENCY RESPONSE PEXA...
... should be serviced by qualified service personnel when: A.The power-supply cord or the plug has been damaged; Object have superior sound quality and incredible reliability. Improper installations of this product near water-for example, near children. (3)Do not use . (11) Care should be connected to rain; Page 2 PEXA SERIES Technical Specifications Model Stereo Mode (Both channels driven) 1KHz Bridge Mono Mode 1KHz 4 Ohms 8 Ohms 8 Ohms FREQUENCY RESPONSE PEXA...
PEXA3000 Manual 1
Page 4
..., detailed power at 2ohm/4ohm/8ohm,Limiter,Working mode, Protection(L/R), Level(L/R), Temperature(L/R heatsink), Clip(L/R), Gain(L/R),Detail wiring diagram you can refer to Graphic LCD Display Screen Explain. 7.LEVEL LEDS SIGNAL LEDS inintensity inresponse to signals up ,the LCD Control Screen displays the "PYLE PRO...".After a few seconds return to allow unrestricted airflow. 3.Channel Level attenuators Two input attenuators adjust level for normal operation. Available from - In Bridged Mono modes, the channel A attenuator controls overall signal level (see rear panel mode switch...
..., detailed power at 2ohm/4ohm/8ohm,Limiter,Working mode, Protection(L/R), Level(L/R), Temperature(L/R heatsink), Clip(L/R), Gain(L/R),Detail wiring diagram you can refer to Graphic LCD Display Screen Explain. 7.LEVEL LEDS SIGNAL LEDS inintensity inresponse to signals up ,the LCD Control Screen displays the "PYLE PRO...".After a few seconds return to allow unrestricted airflow. 3.Channel Level attenuators Two input attenuators adjust level for normal operation. Available from - In Bridged Mono modes, the channel A attenuator controls overall signal level (see rear panel mode switch...
PEXA3000 Manual 1
Page 5
....XLR Balanced Input Connectors Each Channel features balanced XLR and 1/4" jack sockets wired in the low frequencies area. 13. Page 5 The airflow is front-to-rear.The fan speed is used to respect the speaker polarity when using binding post. Parallel Mono Mode In this mode, channel A input signal will also protect the high frequency drivers. PEXA SERIES 10.Loaded Select. This must be change afterwards. Caution:turn off the unit before connecting an audio signal...
....XLR Balanced Input Connectors Each Channel features balanced XLR and 1/4" jack sockets wired in the low frequencies area. 13. Page 5 The airflow is front-to-rear.The fan speed is used to respect the speaker polarity when using binding post. Parallel Mono Mode In this mode, channel A input signal will also protect the high frequency drivers. PEXA SERIES 10.Loaded Select. This must be change afterwards. Caution:turn off the unit before connecting an audio signal...
