Poulan 1980-06 Support and Manuals
Get Help and Manuals for this Poulan item
View All Support Options Below
Free Poulan 1980-06 manuals!
Problems with Poulan 1980-06?
Ask a Question
Free Poulan 1980-06 manuals!
Problems with Poulan 1980-06?
Ask a Question
Popular Poulan 1980-06 Manual Pages
User Manual - Page 1
Beaird-Poulan Division
Emerson Electric Co. 'Ill'
-,:r4t4;14'y o>95..attit" resita, C 'ogre."
•
Poukin®
3400 Counter-Vibe'
CHAIN SAW
OPERATOR'S MANUAL
A WARNING:
Carefully read and follow Safety Rules, Precautions and Operating Instructions. Shreveport, Louisiana Failure to do so can result in serious personal injury.
User Manual - Page 2
...Engine Fuel Mixture
F. B. Tree Felling Techniques
12
C. Trouble Shooting Chart
22
J. IN. Bar and Chain Oil
Using Your Saw
A. Basic Cutting Technique
2
3, 4 & 5
r
6
7
7
w
7
7
8 9
10 10
10
11 11 11
B. Maintenance Chart
23
Parts List
24
Parts & Service
Back Cover
HANDLEBAR
/ MANUAL OILER
REDUCED-KICKBACK GUIDE BAR
THROTTLE LOCKOUT THROTTLE TRIGGER CHOKE...
User Manual - Page 5
...setting the saw only in a tree. 4. For example, if improper tools are used to remove or hold the flywheel when servicing the clutch, structural damage to the flywheel can cause nerve and circulation damage and tissue necrosis. Inspect the unit and repair or replace parts...
3.
SAVE THESE INSTRUCTIONS Do not operate ...and the Guide Bar and. and relevant state safety codes when using...
User Manual - Page 6
...Guide Bar (Contiol Tip®) - Handguards - You must follow these parts. Reduced-Kickback GuideBar, designedwithasmall radiustip whichreducesthe sizeofthekickback danger zone on page17 &18. Failure to follow all safety precautions, instructions and maintenance in this manual.... All U.S. forest land and the states of California Codes 4442 and 4443. Muffler and spark arrestor maintenance is...
User Manual - Page 7
...
SLOTS
O
O
INNER PLATE (2 Slots)
Figure 8 GETTING READY
1. c.
Your Poulan® dealer is sharp and can result..
1. No other
tool is a special piece of equipment designed
re
to become familiar with your saw model, when replacing these parts. Align the spur over the bar mounting studs. INNER GUIDE PLATE
0
BAR CLAMP
BAR
MOUNTING
NUTS
43
Figure...
User Manual - Page 10
...a small amount of fuel mixture. Use the manual oiler to remain in the
tank to be activated.
5. Poulan® lubricant resists high temperature
thinning. Never
...guide bar. anytime an additional supply of learning how to heat and friction. Lubricant- CONTROL DEVICES
Understanding the control devices on the chain. Replace the oil cap securely.
3. If less oil is an important part...
User Manual - Page 13
... movement in the log if you make the first cut deeper
than the bottom of fall completely, set the saw to avoid kickback and chain damage. Be alert for cutting a fallen tree to cut ... twisting and falling in the desired direction. A notch is made on the side of wood could be poorly supported. Make the notch cut is ready to open upthe cut on the opposite side. T
NOTCH -J \
:1-...
User Manual - Page 15
... wire disconnected - Remove larger, supporting branches with the 1/3, 2/3 cutting techniques described in the maintenance section of this manual) performed by a qualified service dealer. Limit pruning to a ...work . Allowingsuch contactcanresultinserious personal injury.
ELWARNING
Have all adjustments or repairs (except carburetor adjustments) with an overcut farther out from the ...
User Manual - Page 16
... OFF CORNER
025
r•
ROUNDED CORNER
Q.
to the manufacturer's specification for the chain you even though it first. WARNING Maintain the proper hook angle according to the center of your Guide Bar and Chain by the saw properly and as recommended in this manual.
-Maintaining correct Chain Tension, page 8. -Proper lubrication, page 10...
User Manual - Page 18
... not work properly and must be repaired.
• Replace the starter rope if the rope ...Set the gap between the electrodes to your dealer.
8. Replace the spark plug in the notch as shown. If the spring pops out, serious personal injury can be replaced. NOTE: The recoil spring, located beneath the pulley, is hard to let a qualified service dealer handle this reason, you do try to repair...
User Manual - Page 19
...service dealerfor fullclutchinspectionandserviceafter each 100 hours of the operator.
• Clutch maintenance is installed in Figure 47. Remove the bar clamp, outer guide plate, guide bar, and chain.Figure 46.
3. push it down and engage the spring.
14. Figure 43. 16. Proper disassembly and repair.... Set the pulley into the housing; Replace and tighten the pulleyscrgew. 15. Replace fan...
User Manual - Page 20
...the RPM speeds up to let a qualified service dealer make carburetor adjustments. Loss of cutting ... to recheck the low speed mixture setting after the idle speed has been ...replacing the clutch. Remove worn drum/sprocketand replace. 7.
Turn the Low Speed Mixture Screw slowly clockwise -S until they are made .
3. b. II a Allow engine to idle. CLOCKWISE REMOVE CLUTCH
INSTALL...
User Manual - Page 21
...Screw 1/16 of 5 isolator mounts. Allow filter to gasoline and oil for proper idle mixture setting. mounts develop an out of time.
3. Store the chain in a container filled with a ... caused from exposure to dry. 8. frequently, especially under very dusty conditions. - Figure 51. Replace all five isolators when a failure to pre- NOTE: This will damage your saw is idling....
User Manual - Page 22
... Plug and regap,
page 18.4. Contact a qualified service dealer.
1. Clean or replace air filter, page 21. 4. Chain cutter tops not filed flat.
2. See Chain Sharpening Instructions, page 16.
..1. Ignition Switch off. 2. Choke partially on. 2. High speed needle requires adjustment. 3. High Speed Mixture set too high.
3.
Install new plug, page 18.
4. Contact a qualified...
User Manual - Page 28
..., Louisiana 71139-9329
66640-1-27885-1-27885 BEAIRD-POULAN /WEED EATER \ Division Emerson Electric Co. PARTS AND SERVICE
Your Beaird-Poulan/Weed Eater product has been expertly engineered and carefully manufactured to safety.
For replacement parts, have available the following information: a. FOR SERVICE OR REPLACEMENT PARTS: 1. Parts and repair service are sent to your :saw differs...
Poulan 1980-06 Reviews
We have not received any reviews for Poulan yet.