Polk Audio RC60i Support and Manuals
Get Help and Manuals for this Polk Audio item
View All Support Options Below
Free Polk Audio RC60i manuals!
Problems with Polk Audio RC60i?
Ask a Question
Free Polk Audio RC60i manuals!
Problems with Polk Audio RC60i?
Ask a Question
Popular Polk Audio RC60i Manual Pages
DIY In-Ceiling and In-Wall Installation Guide - Page 1
Installing Your In-Wall or In-Ceiling Speakers
DIY In-Ceiling and In-Wall Installation Guide - Page 2
... codes-your retailer or home center service personal will take you 're up for it -yourselfer. But if you choose walls or ceilings that hole will need to cut or slice in a motion away from your body.
If you answered yes to be a barrier to see below to accomplish for any of installing Polk speakers. This Guide...
DIY In-Ceiling and In-Wall Installation Guide - Page 4
Section 2: Polk Audio In-Wall and In-Ceiling Speaker Installation Guide
Materials and Preparation Before cutting into your walls to install your new Polk Audio speakers, gather up all basic speaker applications you will need a minimum of 2 conductors, thus the term cable is used here instead of "wire".
2) Be certain that you have enough speaker cable-it is always a good idea to cut...
DIY In-Ceiling and In-Wall Installation Guide - Page 5
... sure there is two sets of speaker cables to each speaker within a room should be about the same to the speakers. Scenario 3 The speakers will be installed in the ceiling for music in most... sensor. In home theater installations the cable lengths for Front Left, Center and Right channels should be about where you want to install your new Polk speakers, we suggest you have established...
DIY In-Ceiling and In-Wall Installation Guide - Page 6
...a small exploratory hole
Bend a stiff wire at a right angle
Use the wire to the wall or ceiling. If you feel no obstructions, now you can cut the opening for wires, pipes and obstructions in the... then using a stiff wire or bent coat hanger "feel" for your Polk speakers tape the supplied templates to "feel" for the speaker. Once you have to go to an alternate location that one location won...
DIY In-Ceiling and In-Wall Installation Guide - Page 7
... on how large of a hole you may be an issue because of the small holes - Polk Audio can recommend a professional installation company, call (800) 377-7655 during normal east coast business hours. Hot and cold water pipe
Installing the speaker cables: A few rules, some general guidelines and a couple of 10! Standard stud sizing is a deal...
DIY In-Ceiling and In-Wall Installation Guide - Page 8
...Notches must NOT exceed 25% the width of the stud
speaker cables
WRONG! Running speaker cable with as much distance as practical:
National Electric Code does not allow low voltage cable to the right show .... DIY CI Tutorial 8
In load bearing walls be installed in the same holes or boxes
as AC. speaker cables
AC wiring
Studs in two categories: "load bearing" and "non-load bearing...
DIY In-Ceiling and In-Wall Installation Guide - Page 13
... the base molding for your new Polk speakers.
rotating cam clamps
Our speakers utilize a unique "rotating cam" that presses the front baffle casing to the walls and ceiling. Phillips head screw, accessed from the front side of the speaker
baffle plate
D I Y C I T u t o r i a l 13
In most cases walls are ready to install your speakers into the hole with paint...
DIY In-Ceiling and In-Wall Installation Guide - Page 14
Set your power driver's torque setting to "1" to over -tightening screws. D I Y C I T u t o r i a l 14 Strip your screwdriver. Be careful not to help avoid over tighten the speaker-the dry wall or sheet rock could dimple, or break. View of the speaker: (note* Reminder-for an easier installation if you are using a power driver. This is most likely to happen if...
DIY In-Ceiling and In-Wall Installation Guide - Page 15
... terminating the cables near the receiver or amplifier with a wall plate, this allows a very clean finish, without any gaps or holes in the wall. Finally install the grill:
Terminate the speaker cable to the binding post inserts and install like your speakers:
D I Y C I T u t o r i a l 15 Your friends will think a professional did the...
RCi Series Manual - Page 1
RCi SERIES
RC60i RC80i RC55i RC65i RC85i
O w n e r 's Manual
High Performance In-Wall Speakers Haut-parleurs encastrables Haute Performance « In Wall »
RCi Series Manual - Page 5
...Service, call 800-377-7655. 5 The grille of spray paint. Be careful not to exposed (unmasked parts...models: Before spray painting the grille, carefully remove the grille's fabric scrim by carefully hooking it with a bent paper clip and pulling it will not get wrinkled.
4. You will not interfere with paint [figure 9].
5. The special fabric scrim hides the speaker's drivers... setting....
RCi Series Manual - Page 7
... speakers (see specification page... can support the weight of your model).
&#...ceiling material. This is black (-). SUIVEZ CES SIMPLES ÉTAPE:
• Assurez-vous que le matériau dans lequel vous comptez installer vos haut-parleurs (plâtre, placoplâtre, lambris, pierre, etc.) peut supporter...(round). Suivez les instructions de raccordement fournies avec...Customer Service, call...
RCi Series Manual - Page 8
...reinstall the grille by fitting it is just resting on the RC55i, RC65i and RC85i models, tighten the center screws before tightening the corners for the most flush fit to engage... the speaker carefully into your cutout without nicking your speaker.
• Loosen the rotating wall clamps by fitting it to pry between the grille and the speaker frame.
• To install the speaker, first...
RC60i Wall Mount Template - Page 1
... mounting location. 3) Trace along the outside of the template. 4) Carefully cut a hole ensuring that it is no larger
than the shape you traced. 5) Refer to manual for installation instructions. RC60i Mounting Template
Follow these steps before installing the RC60i.
1) Determine speaker location.
Polk Audio RC60i Reviews
We have not received any reviews for Polk Audio yet.