Pfaff hobby 803 Support and Manuals
Get Help and Manuals for this Pfaff item
View All Support Options Below
Free Pfaff hobby 803 manuals!
Problems with Pfaff hobby 803?
Ask a Question
Free Pfaff hobby 803 manuals!
Problems with Pfaff hobby 803?
Ask a Question
Popular Pfaff hobby 803 Manual Pages
Owner's Manual - Page 2
..., 806 and 807 Utility stitches, models 802 to 807 Stretch stitches, models 806, 807 Thread tensions Changing the needle Reverse sewing Dropping the machine feed Changing the sewing foot Sewing feet Special sewing feet Buttonhole settings Sewing buttonholes Fitting detachable workplate Changing the light bulb Cleaning and oiling Trouble shooting
Page 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 9
10 10 11...
Owner's Manual - Page 4
...with the letter N or coloured black. Parts of your sewing machine
1 Take-up lever 2 Thread guide 3 Bobbin tension stud
(for a while. The ...code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in the sewing lamp. C) A 15-watt bulb is the maximum size of machine arm) 21 Needle set...
Owner's Manual - Page 5
...sewing. Before putting the machine away after sewing replace the receptacle in the slot. On models 800, 802 and 806 place it into
the free arm.
7 -/ 800,802,806
4/- J 1 Foot control receptacle Remove this proce dure, making sure the bottom of the cover (G), move them back up (H) and
then remove the cover (I).
Removing the carrying case... cover Open the hinges on models 801, 803 ...
Owner's Manual - Page 6
Foot control Place the foot control on the floor under the table. The machine starts sewing. The more you press down with your foot. Your machine is now ready for sewing. Press it down the pedal, the faster the
machine runs.
2 Electrical connection Push plug G into the machine socket and plug H into the wall socket.
Owner's Manual - Page 8
... place a spool of them. Pass the thread from the spooi around the bobbin a few times and push the bobbin to the right for winding. When the bobbin is full push it to re-engage the sewing mechanism. Bobbin winding
Disengage the sewing mechanism. Disengaging the sewing mechanism Before you . To do this, hold the hand wheel steady...
Owner's Manual - Page 9
Cutout H must be flush.
5 Release the latch. Stud G and latch I and push the bobbin case onto stud B as far as it will go.
Inserting the bobbin Insert the filled bobbin in the bobbin case so that the thread unreels towards the back (G). Inserting the bobbin case Pull up latch I must point upwards. Then draw the thread into slot H and under the spring into eye I.
Owner's Manual - Page 11
... bar litter Lever 20 has three positions. Position I
7 Turn hand wheel 9 toward the left and back under the sewing foot. Drawing up the bobbin thread Hold the needle thread a little taut. Pull the bobbin thread out of the needle hole and lay both threads toward you
remove the work, turn the balance wheel...
Owner's Manual - Page 12
... downwards to set at mark G on models 806 and 807.
/- Regulating the stitch length The stitch length is an oblique slot lRoofacitashteeedtmheaatcsthehiwenienbgatocwfkoaoortfd.
The numbers indicate the length in mm.
H shows how to cut them. tPhthueellpbtrhaeecskswe. Fig. N
7
\
8 Thread cutter (G) The thread cutter is set the stitch length control for sewing stretch stitches...
Owner's Manual - Page 14
....ttageepohttsTeceohetttushhocFsrsseetnritiegoibtdl.brrctleeiheohbacoqetletfatuoyloruoitroemrhnweueatdi)tl,
zigzag-width.
7
10 and stretch-stitch 5 should only be turned in the red sector on the machine and
explained on page 11. Selecting utility stitches on
models 802 to 807 The various utility indicated by black of the stitch panel
stitches possible are letters in a
selector dial...
Owner's Manual - Page 15
... 802-807 A Straight stitch B Zigzag stitch C Elastic stItch D Blindstitch E Elastic decorative stitch F Shell-edge stitch
Models 802 and 803 have utility stitches A to D.
Stretch stitches, models 806, 807 A Elastic triple straight stitch B Elastic triple zigzag stitch C Honeycomb stitch D Pullover stitch E Feather stitq\h F Overlock stitch
4
A
A
B
AAAAAAA/
C
i)\/\i\i\I\/\i I V V V VU...
Owner's Manual - Page 16
... correct. The higher the number, the tighter the tension.
J = Upper tension too loose or lower tension too tight. J
4
I-
1
K
12 The correct lower tension Let the bobbin case with a full bobbin hang down by the thread. The normal tension
setting is in the white range between 3 and 5.
Upper tension (19...
Owner's Manual - Page 20
... models 5 to B.
802
to
807
set
utility-stitch
dial
Push let it bears against its stop. Move zigzag-stitch 4 to into
buttonhole symbol G position.
Release bracket M so that it there. Set the stitch
and
density in the buttonhole sector of the foot, pull it
taut and clamp it in front lug K. As you sew...
Owner's Manual - Page 22
... holes in the machine base. Press the workplate down (Fig. Turn catch G on models 800, 802 and 806 The foot control receptacle of these models also serves as a detachable
workplate. Swing the support down a little after fitting.
(Figs. Turn the receptacle round and fit it to the machine so that its two guide pins enter the...
Owner's Manual - Page 23
...
the
machine. Tilt the machine back and turn it and pull it
so
that
the top is in slots I. Push it
towards H. (Fig. Pull out the plug. Insert the new its pins slide in front of you. On models 801, screws and needle plate
remove cover 15 803, 807: remove (Fig. J).
19 G). Remove the bobbin case...
Owner's Manual - Page 24
... and push it up as far as it will go . Let machine feed the work is pushed or pulled. When inserting the bobbin case, press against it until it will go , its flat shank side...lightly.
Needle too thin for thread used . Needle bent and strikes needle plate because work alone.
Trouble shooting
Cause:
1.
Poor-quality or knotty thread used, or thread that has become too dry by...
Pfaff hobby 803 Reviews
We have not received any reviews for Pfaff yet.