Pfaff 212 Support and Manuals
Popular Pfaff 212 Manual Pages
Owner's Manual - Page 2
...en Is
Page
POllS of inodOl 212
2
Paris of model 213
4
I lEO trii:il ( OnnE(cfiuo
(5
Work support of model 213
7
tternovirrg tile bobbin case
B
Diserigiiginq the sewing rnecharicri B
.iioifig he tiobhirr
... the sewiriij toOt Drop! imniij lIne machine iced Basic rules Safely rules Sir Omillit sliP Ii aiol iigiaq Smwtriq un buttons Sewing buttonholes Blnndst itching hems loser log zippers...
Owner's Manual - Page 3
...
23
iPFAFFI 217
22
I
10
21
11
12 20
19 18
13
Parts of the PFAFF 212
I luke up lever 2 1 bread guide 3 Bobbin winder tension with
thread guide 4 Utility stitch Selector 5 Utility stitch chart 6 Colour range selector 7 ...16 Shuttle (not visible) 17 Beitplate cover 18 Sewing toot 19 Sewing tool holder wit ti s( rev 20 Needle bar 21 Thread guides 22 Sewing light switch 23 Face cover 24 bread I ...
Owner's Manual - Page 4
...
23 10
11
21
12
20 19
18
4
17
16
15 11
13
Parts of the PFAFF 213
1 Take up lever
2 Thread guide
3
Bobbin winder thread guide
tension
with
4 Utility stitch selector
5 Utility stitch chart
6 Colour range selector
... plate 18 Shuttle (not visible) 19 Sewing foot 20 Sewing toot holder with scre 21 Needle bar 22 Thread guides 23 Sewing light switch 24 Face cover 25 Thread tension...
Owner's Manual - Page 5
... and plug 2 into the wall outlet. The more the pedal is depressed, the faster the machine runs
Work support of your foot. Place foot control 3 within easy reach of model 213
fo enlarge the sewing area for ordinary
sewing operations, push the work sup
port onto the free arm as tar as it will
go...
Owner's Manual - Page 6
... the bobbin case out Then release the latch so that the bobbin can drop out 8
Disengaging the sewing mechanisri
FIg. 5
Hold the balance wheel steady wdh y left hand and, with your right hand,...its highest point. Removing the bobbin case Fig 3.Model2l2 Fig. 4: Model 213
Turn the balance wheel toward you ( arrow in Fig. 5) The sewing rnechani is now disengaged To engage il agi turn the knob away ...
Owner's Manual - Page 7
Winding the bobbin Select the thread from the chart on the inside front cover
Disengage the sewing mechanism and place a spool of thread on pin 1 (Fig 0) Push a bobbin onto spindle 4 (... (see arrow) Wind a few turns of thread on bobbin 3 in the direction indicated by an arrow Run the machine, iIhen the bubbin is lull, the bobbin winder will stop automatically Remove the bobbin If you do not need a ...
Owner's Manual - Page 9
...Turn the balance wheel toward you release the control, the machine will sew forwards again
ii
-' -- -
- --
----.-
--
-S-,-- Regulating the stitch length and sewing backwards
Fig. 13
Hold the end of the needle hole... 10 cm or 4 inches long> hack under the sewing toot
Fig. 14
14
1 White utility stitches The stitch length is set by turning stitch length control A until the needle moves...
Owner's Manual - Page 13
Dropping the machine feed
the machine feed has two positions which are set by turning the drop teed knob (Fig 22)
Machine teed dropped for sewing. always raise the take-up lever before sewing -
Be careful to use only a 15-watt ligh bulb in the sewing lamp.
2: Make sure you unplug the power cor whenever you want to...
Owner's Manual - Page 14
... the needle bar to 7. Place a button on the colour range selector Is at the top. left needle position
Zigzag awing
The machine sews zigzag stitches when the utility stitch selecto' is set at 5 or 7 and the mark on as shown in range 9 and the mark on the material and under the needle Lower...
Owner's Manual - Page 18
Removing the work
Raise the needle and the sewing (oot Remove the work trorn the machine by pulling it toward the rear, and trim both threads with the aid of the thread cutter Make sure to leave thread ends about 10 cm (4 inches) long in the machine with which to start the next seam...
Owner's Manual - Page 19
Model 212
A
B
C
C
Model 213
A
B
Co
D
0
F
Fig, 35
ID
Flg36
E
F
35
1
Machine care
Cleaning the shuttle race
Oiling
All bearings behind shuttle race ring
Replace and lock
them in order to get rid of excess oil
34
Raise the ... To do this, remove the bobbin case
Always use high-grade (resin -free) sewing
machine oil After oiling, run for a short time on a piece
the...
Owner's Manual - Page 20
... tensions as indi Needle and Thread Chart.
Sewing foot, shuttle or shuttle race may be damaged. Wind the thread properly, as of
it gets entangled. 2 The bobbin thread has slipped out
from front to back
Turn tension dial toward the back.
6.
needle 5. Replace the damaged part or send it in the
of the...
Owner's Manual - Page 21
... qualify
38
Remedy Use a thicker needle as indicated in the Needle and Thread Chart
Raise the sewing foot and draw the needle thread between the tension discs
39
) Faulty stitching
Cause 1 Both ...accord
3 The needle thread is not placed be tween the tension discs
Remedy Adjust both lensions as instructed on page 17 Select needle and thread to Suit the material, as indicated in the Needle and ...
Owner's Manual - Page 22
Machine runs heavily and is noisy
Cause• 1 Dust and pieces of thread have accu
mulated in the shuttle race 2 Machine has not been serviced for a
longer time 3 The machine is clogged by interior oil
40
Remedy Clean the shuttle, as instructed cii pages 34 and 35 Read the instructions on page 34
Have a mechanic clean the machine thoroughly.
Pfaff 212 Reviews
Do you have an experience with the Pfaff 212 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Pfaff yet.
Earn 750 points for your review!