Panasonic EYFLA4AR Support and Manuals
Get Help and Manuals for this Panasonic item
This item is in your list!
View All Support Options Below
Free Panasonic EYFLA4AR manuals!
Problems with Panasonic EYFLA4AR?
Ask a Question
Free Panasonic EYFLA4AR manuals!
Problems with Panasonic EYFLA4AR?
Ask a Question
Popular Panasonic EYFLA4AR Manual Pages
EYFLA4AR User Guide - Page 5
... by a qualified repair person using .... operation. Service
1) Have your power tool serviced by the...power tool. in accordance with specifically designated battery packs. Inserting ...Instructions" booklet and the following before using only identical replacement parts. III.ADDITIONAL SAFETY
RULES
1) Wear ear protectors when using the tool for a long period.
6) When storing or carrying the tool, set...
EYFLA4AR User Guide - Page 6
... from the tool.
Insert the bit into place
over the groove. To remove the bit, pull out the collar in the center position (switch lock).
1. EYFLA4A/EYFLA4AR/EYFLA5A/EYFLA5AR
12 mm (15/32")
9 mm - 9.5 mm 6.35 mm (23/64" - 3/8") (1/4")
NOTE: Be sure to attach the rubber ring to its original position when...
EYFLA4AR User Guide - Page 8
... the holder.
2.
Pull out the battery holder. 1 Push in . To remove the battery pack: Push up on the button from the front to the wire- Replace it with a fresh battery. • The included battery is dead. 2. Insert the battery and push the holder back in on the tool. • Under the...
EYFLA4AR User Guide - Page 9
...- Depress the trigger switch slightly to another pack. Tool needs cool off time before use , set to check whether the torque control function was activated.
CAUTION: • The built-in LED light...use or its center position (switch lock). This tool has the built-in LED light is set the lever to its battery capacity.
Check the direction of the tool surface, do not operate...
EYFLA4AR User Guide - Page 10
... slightly with a fresh unit), even if the trigger is designed to be charged (or replaced with factors such as necessary for the work where a heavy load comes to bear during the... The torque control function will not operate until the battery pack has been charged (or replaced with ambient temperature and battery characteristics. Adjust the torque as the material into which the ...
EYFLA4AR User Guide - Page 11
... "F" indicates that is not operated for the work being tightened: Material, seating surface finish
Setting the tool to configuration mode
1.
Engage the switch while pushing the button and then release both...the and buttons to configuration mode. Configuring the torque clutch setting (1)
(2)
NOTE: • Tools ship from the factory set to "F" mode (torque control function off). • The...
EYFLA4AR User Guide - Page 12
... snug point detection level from the Tightening Torque Chart to guide your selection of torque clutch setting. (See the following tightening torque chart) 2. Setting the snug point detection level from "L2" may increase the torque. Model
EZFLA4 EZFLA5
Number of torque stages setting 1 to 8 1 to "L2."
Press the OK button to accept the selected torque...
EYFLA4AR User Guide - Page 13
... this chart were measured under the conditions described below and are easily cracked or deformed, etc. Set the tool to verify the new value after it automatically stops as a result of holding the...control function, even if the switch is engaged.
1. Press the interval set button. • The control panel will be displayed.
Press the OK button to prevent the tool
from ...
EYFLA4AR User Guide - Page 14
... setting 1. Battery indication lamp: The upper and lower bars of shipment from the factory.
• The error display...
Qualifier.
Set the tool to register the tool and assembly qualifier, see the assembly qualifier instruction manual. Display ...lamp: The middle bar of the battery flashes on /off setting (EYFLA4AR, EYFLA5AR, EYFLA5QR, EYFLA6PR) 1. Radio signal range limitation function ...
EYFLA4AR User Guide - Page 15
...set display lights up.
Remove any dirt.
Replace the battery pack.
Display
Likely cause
Corrective action
Setting error
... too hot. Error Display
In the event of drive component parts (hammer, etc... The contacts that the Assembly Qualifier's group setting has been configured correctly.
• Improve ...set display is too hot to be used in the following chart before having...
EYFLA4AR User Guide - Page 16
... are found on how to recycle this battery.
[Battery Charger]
Charging
Read the operating manual for Panasonic battery charger for an hour in a location where the temperature is 5°C (41°...the product you have a limited life. If the operation time becomes extremely short after recharging, replace the battery pack with a new one terminal to another. The battery pack cannot be affected ...
EYFLA4AR User Guide - Page 17
... a residential installation. Panasonic Electric Works Power Tools Co., Ltd. 33, Okamachi, Hikone, Shiga, Japan
- 17 - FCC Caution: To assume continued compliance, install and use in the instructions. These limits are designed to operate this equipment does cause harmful interference to part 15 of the FCC Rules. This Class B digital apparatus complies with the instructions, may cause...
EYFLA4AR User Guide - Page 18
VIII. SPECIFICATIONS
MAIN UNIT
Model
Motor Chuck size
EYFLA4
A
AR
Single- 9 - 9.5 mm ended (23/64" - 3/8")
EYFLA5
A ...
Weight (with battery pack: EYFB40)
---------
1.4 kg (3.1 lbs) 1.5 kg (3.3 lbs)
BATTERY PACK (not included with shipment)
Model Storage battery Battery voltage
EYFB30
EYFB40
Li-ion battery
10.8 V DC (3.6 V/6 cells)
14.4 V DC (3.6 V/8 cells)
BATTERY...
EYFLA4AR User Guide - Page 19
...(13/32") Approximately 29 g (0.6 lbs)
Assembly Qualifier (not included with shipment)
Model Rating Dimensions
Weight
EYFRZ01
EYFR02
See the rating plate on the bottom of the Assembly Qualifier...
Model Indoor/Urban Range Outdoor RF line-of-sight range Transmit Power Assembly Qualifier Sensitivity FCC Part 15.249 Industry Canada
EYFLA 100ft./30m 300ft./100m 1mW(0dBm) -92dBm(1% packet error)...
Panasonic EYFLA4AR Reviews
Do you have an experience with the Panasonic EYFLA4AR that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Panasonic yet.
Earn 750 points for your review!